EcoxGear SEI-ETAMP7700 20 Series Bedienungsanleitung

ExtremeTower

8 inch Tower Speakers

Installation Guide

Built-in Ampliﬁer

ExtremeTower TA8

Models: SEI-ETAMP7700...20

Bluetooth Ampliﬁed

Tower Speaker

Passive Tower Speaker

Bluetooth Ampliﬁed

Tower Speaker

Passive Tower Speaker

Battery

ExtremeTower TB8

Models: SEI-ETBAT7700...20

· Please read the Hardware Guide, this Installation Guide, and the

User Guide before installation and use.

· This Installation Guide is for the TA8 (SEI-ETAMP7700...20) and

TB8 (SEI-ETBAT7700...20) ExtremeTower Speakers. The TA8

Speakers do NOT include a removable, rechargeable battery. You

can purchase the battery separately.

· Only connect a 12V Power Supply to the Ampliﬁed Speaker power

input. To prevent damage to the speakers, ﬁre, and/or possible

injury, do NOT connect the BLACK Power Cable to the battery’s

negative (-) terminal until all the installations are completed.

· CAUTION: Do NOT connect to a 24V, 48V or 72V power supply!

The voltage for the power input is +12VDC. You need to connect

to a 12VDC power supply. If your vehicle battery power is not 12V

(e.g., 24V, 36V, or 48V), you will need a DC-DC voltage converter

with 12V output (e.g. a 48V-to-12V converter). Connecting the

ExtremeTower directly to higher voltages will cause damage to the

speaker and cause the rechargeable battery to overcharge and

overheat! In extreme cases, excess voltage can cause the battery

to expand, leak, or potentially catch on FIRE! Any damage to the

battery due to improper connections to higher voltages will VOID

THE PRODUCT WARRANTY.

· The Amplified Speaker has a Remote Turn-On Input feature; this

is to ensure that the speaker is completely powered off (no battery

consumption) when your vehicle is not in use. When the Remote

Turn-On Input has a 12V signal, the speaker will turn on or go into

standby, depending on the Power Mode Switch settings. When

there is no input voltage, the speaker will turn off. In general, this

Remote Turn-On signal comes from the vehicle ignition switch

– make sure that the signal voltage on the ignition switch is 12V. If

your vehicle ignition switch signal is not 12V or if you are not able to

get a connection to the ignition switch, you can connect the Remote

Turn-On Wire on the Amplified Speaker to a rocker switch. Then

connect the rocker switch to a 12V power supply or the 12V output

on your voltage convertor. Additionally, some vehicles have a built-in

12V switch panel, which will also work for the Remote Turn-On Wire.

Important

· When mounting the speaker, it is extremely important to make sure

that the mount is secure and will not cause any potential issues.

Please check that the speaker does NOT block the driver’s view or

prevents the safe operation of your boat or other vehicle. Ensure

that all screws are tightened and the speaker is secured correctly

so that the speaker will NOT fall.

· It is highly recommended to periodically check that the mount is

secured. If loose, please retighten the Locking Screw Latch.

RECOMMENDATION: Do NOT install on your own. This installation

is a two-person job, to be done safely. Please be careful to ensure

no personal injury or damage to your vehicle.

· An Aviation Connector Jack Cap comes attached to the

Base-Mount on each speaker. If you choose to use the Deutsch

Cable Set for wiring, you MUST screw the cap into the unused

Aviation Connector Jack on each speaker, tightening it clockwise

with a long nose plier (not included) or similar tool. Failing to do

this may result in potential water or moisture penetration into the

jack connector pins, cause damage to the speaker, and VOID THE

PRODUCT WARRANTY.

· When you connect the 9-pin or 6-pin Aviation Connector to the

Aviation Connector Jack in the Base-Mount, you MUST ensure

the connector is tightened (clockwise) so that the connection

is waterproof.

· When using the Extension Cable and/or connecting two wires

(e.g., using supplied BUTT Connectors), make sure to seal

the connection either by using electrical tape or heat shrink

tubing. Failing to do this may result in long-term corrosion on the

connection and cause a premature malfunction.

CAUTION: After taking the product out of the polyethylene bag,

be sure to dispose of the polyethylene bag out of the reach of

children. Children may play with the bag, which could result in the

child’s suffocation.

Important

ExtremeTower Passive Speaker Layout

ExtremeTower Overview

SpeakerParty Lights

Rotating 360°

Mount Clamp

Top Mount

Clamp

Quick-Release

Knob

U-Shaped Pin

Tweeter

Base-Mount Bottom Mount

Clamp

ExtremeTower Ampliﬁed Speaker Layout

ExtremeTower Overview

Switches

Dome Light

Back Cover Latch

Release Button

Battery Pack

Control Buttons

Waterproof

Back Cover

ExtremeTower Overview

Audio, LED Control Signals, and Power

Connectors and Cables

Ampliﬁed Tower Speaker and Passive Tower Speaker

· Your package has one Ampliﬁed Tower Speaker and one Passive

Tower Speaker.

· The Passive Tower Speaker must be connected to the Ampliﬁed

Tower Speaker to receive audio and LED control signals.

Power, Audio, and LED Lighting Connections

The Ampliﬁed ExtremeTower Speaker has 9 input and output wires.

· 3 Input Wires: 12V (+), GND (-), and Remote Turn-On to connect to

your vehicle.

· 6 Wires: To connect both speakers together.

The Passive ExtremeTower Speaker only has 6 input wires.

Power + 12V DC

Ground

Remote Turn-On

Speaker Detect

LED Power

LED Ground

Speaker -

Speaker +

LED Signal

Speaker Detect

LED Power

LED Ground

Speaker -

Speaker +

LED Signal

ExtremeTower Overview

Speaker Connector Jacks

Each speaker has 2 types of Connector Jacks.

1. A round Aviation Connector Jack is inside the speaker

Base-Mount, which allows the cable to pass through the

Bottom Mount Clamp and go into a hole in the crossbar at the

location where the speaker is mounted. The Ampliﬁed Tower

Speaker has a 9-pin, round connector jack, and the Passive

Tower Speaker has a 6-pin, round connector jack.

2. A square Deutsch Connector Jack is behind the speaker

Base-Mount underneath a rubber cap. This is for an installation

where the wire is installed outside of the tower / roll cage.

6-Pin Aviation

Connector Jack

9-Pin Aviation

Connector Jack

6-Pin Deutsch Connector Jack

4-Pin Deutsch Connector Jack

This is also the connection suggested if you want to utilize the

Quick-Release-Mount option.

The Ampliﬁed Tower Speaker has both a 4-pin and a 6-pin,

square connector jack. The Passive Tower Speaker only has

a 6-pin square connector jack.

FM Dipole Antenna Jack

The Ampliﬁed Speaker has a built-in FM Antenna. It also includes an

FM Dipole Antenna Jack for an optional external antenna connection

and improved reception (dipole antenna sold separately). If you

prefer to use an external FM antenna, follow these steps:

1. Slowly pull out the rubber cap. Keep the rubber cap attached to

the speaker housing if you plan to remove the antenna periodically;

otherwise, you can remove the antenna cap.

2. Plug your dipole antenna into the FM Dipole Antenna Jack.

ExtremeTower Overview

FM Dipole

Antenna Jack

ExtremeTower Overview

INT EXT

3. Open the Back Cover (refer to Install the Rechargeable Battery

Pack to the Ampliﬁed Speaker for details), move the (Blue) FM

ANT Switch to the EXT position.

Cables

Your package includes 2 Cable Sets for each wiring option.

1. Aviation Cable Set — For easy running and fishing wires

through a crossbar. The Aviation Cable connection between the

Amplified Tower Speaker and the Passive Tower Speaker uses

the following two cables:

· The long cable (“Round A1” 9-pin to 6-pin pass-through Aviation

Cable) has a 9-pin round connector on one end and 3 bare wires

for power inputs and 6 Bullet connectors on the other end for

interconnection with the Passive Tower Speaker.

“Round A1” 9-Pin to 6-Pin Pass-Through

LED and Speaker Aviation Cable

3 Bare Wires (Input) 9-Pin Aviation

Connector

6 Bullet Connectors (Output)

ExtremeTower Overview

· 4-pin Deutsch connector for 12V (+), GND (-), and Remote

Turn-On input for the Ampliﬁed Tower Speaker.

· The short cable (“Round A2” 6-pin pass-through Aviation Cable)

has a 6-pin round connector on one end and 6 bullet connectors

on the other end.

Note: Besides the Power +12V, GND, and Remote Turn-On

connections to your vehicle’s battery and ignition switch, you

will need to connect the 6 bullet connectors from both the long

and short cables and seal the connections to prevent water or

moisture penetration.

2. Deutsch Cable Set —Suggested wiring method if you want to

utilize the Quick-Release-Mount option. The Deutsch Cable

connection between the Amplified Tower Speaker and the

Passive Tower Speaker uses the following two cables:

“Round A2” 6-Pin Pass-Through

LED and Speaker Aviation Cable

6-Pin Aviation

Connector 6 Bullet Connectors (Input)

“Deutsch A1” 4-Pin Power Deutsch Cable

4-Pin Deutsch

Connector

Power Inputs: 12V (+), GND (-),

and Remote Turn-On

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere EcoxGear Sprecher Handbücher

EcoxGear

EcoxGear EcoBoulder GDI-EXBM900 Bedienungsanleitung

EcoxGear

EcoxGear SOUNDEXTREME SEI-ETAMPBAT7700 20 Series Bedienungsanleitung

EcoxGear

EcoxGear ECOSTONE GDI-EGST700 Einrichtungshandbuch

EcoxGear

EcoxGear SOUNDEXTREME SEI-ETAMPBAT7700 20 Series Bedienungsanleitung

EcoxGear

EcoxGear EcoEdge GDI-EXEDGE301 Bedienungsanleitung

EcoxGear

EcoxGear GDI-EGST700--710 Einrichtungshandbuch

EcoxGear

EcoxGear EcoDrift GDI-EXDRFT200 Bedienungsanleitung

EcoxGear

EcoxGear EcoXplorer Bedienungsanleitung

EcoxGear

EcoxGear GDI-VXYMHFTWL01 Bedienungsanleitung

EcoxGear

EcoxGear EcoDuo GDI-EXPB2100 Bedienungsanleitung

EcoxGear

EcoxGear 2.5 Marine Bedienungsanleitung

EcoxGear

EcoxGear ECOXBT GDI-EGBT500 Bedienungsanleitung

EcoxGear

EcoxGear SOUNDEXTREME SEI-ET7700 20 Series Bedienungsanleitung

EcoxGear

EcoxGear EcoExtreme 2 Bedienungsanleitung

EcoxGear

EcoxGear EcoBoulder Bedienungsanleitung

EcoxGear

EcoxGear SOUNDEXTREME SEI-ET7700 20 Series Montageanleitung

EcoxGear

EcoxGear EcoBoulder MAX GDI-EXBDR310 Bedienungsanleitung

EcoxGear

EcoxGear GDI-EXBM901 Bedienungsanleitung

EcoxGear

EcoxGear SOUNDEXTREME ExtremeTower TBB8 Montageanleitung

EcoxGear

EcoxGear EcoRoam 30 Bedienungsanleitung

EcoxGear

EcoxGear EcoJourney GDI-EXJRNY02 Bedienungsanleitung

EcoxGear

EcoxGear EcoBoulder+ Bedienungsanleitung

EcoxGear

EcoxGear SOUNDEXTREME LEDCast SEI-SESPKR65 Bedienungsanleitung

EcoxGear

EcoxGear EcoCarbon GDI-EXCBN200...209 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung