EcoxGear GDI-EGST700--710 Einrichtungshandbuch

Quick Start USER GUIDE

ECOSTONE Features & Operation Models: GDI-EGST700--710

QUICK START 1-2-3

STEP 1: Power ON your ECOSTONE

STEP 2: SEARCH your Bluetooth Connection on your Smart-device

STEP 3: PAIR & PLAY

STANDBY

ON/OFF

BLUETOOTH

SPEAKER

VOLUME

TRACK

SELECTION

PLAY PAUSE

ANSWER

LED

FLASHLIGHT

Quick Start USER GUIDE

STEPS 1-2-3 Set Up Recommendations

STEP 1 CHARGE your ECOSTONE

Before you power on your ECOSTONE connect the USB Micro port to the USB cable and a power

source to fully charge your ECOSTONE for best performance.

NOTE: Before using your ECOSTONE for the first time, charge the unit until all 4 LED battery level

indicators are solid green, indicating a full charge.

Typically approximately 3 hours of charging is required from a low to a FULL charge.

Power source options include the USB connection to your computer or a power outlet using a USB to

AC power adapter. Recommend always using the USB cable included with your ECOSTONE.

RECOMMENDATION: always use the USB cable included with your ECOSTONE

STEP 2 Power ON, Battery & LED Status Indicators

Once fully charged, press the STANDBY POWER button on the top of your ECOSTONE.

You will see the green LED light & you will hear an ascending bell tone when powering ON.

IMPORTANT: be sure the MAIN POWER switch located in the back compartment under the cap is set in

the UPPER ON position. IF the switch is in the LOWER OFF position your ECOSTONE will not be able to

turn ON using the Standby button.

The LED battery level indicators are located on the top of the unit. Each bar represents 25%,

4 full LED’s indicates a FULL charge

AUDIO playback time over Bluetooth connection is approx. 12 hours at 75% max. volume

Quick Start USER GUIDE

STEP 3 Bluetooth pairing & your Audio

Connecting with Bluetooth: connect to your Smart-device & play AUDIO

When your ECOSTONE is turned ON the blue LED light on the top panel will flash rapidly indicating the unit is ready to

pair.

Turn on Bluetooth on your Bluetooth device (Smart-device) and set the device in pairing mode. Available Bluetooth

connections shall appear. Select the ECOXGEAR speaker from the list of discovered devices on your Bluetooth device.

Wait for a few seconds until the connection is completed.

When the ECOXGEAR selection is made and the Bluetooth connection is completed your ECOSTONE announces:

“Bluetooth connected”

Once connected, select and play your desired audio

NOTE: IF the LED is not flashing or if you wish to place your ECOSTONE in pairing mode, press and release the

Bluetooth button on the top panel. Your ECOSTONE shall announce “pairing ready” when ready to pair to a new device.

NOTE: Your ECOSTONE shall sync & wirelessly pair with most Bluetooth enabled devices. The unit remembers the last

device paired and will automatically search for previous connections when the speaker is turned ON or when a device

comes back into Bluetooth range. If a connection is lost due to range, the speaker will look to re-establish that connection.

IF Bluetooth is turned OFF on your Smart-device, the ECOSTONE will not automatically look for the device.

RECOMMENDATION: IF you are not familiar with Bluetooth pairing for your Smartphone or other Smart-device refer to

the User Guide for your Smartphone to learn how to add and pair a new device (ECOSTONE for instance) to your

Smartphone using Bluetooth.

NOTE: Bluetooth Pairing & Connections - Once paired, should you have an issue switching between Bluetooth

connections between devices, open the Bluetooth Section within the device currently connected to the ECOSTONE and

delete the Bluetooth connection. The ECOSTONE will then be available to pair & connect to an alternate Bluetooth

enabled Smartphone / Audio Device

Quick Start USER GUIDE

Control Buttons & Connections, Functions & Feature

STANDBY

ON / OFF

PRESS the STANDBY POWER button to turn the ECOSTONE ON/OFF.

When turned OFF the ECOSTONE remains in STANDBY POWER mode.

IMPORTANT: Standby Power function will NOT operate when the

MASTER POWER is set OFF. Master Power Switch on the back panel

must be set ON for Standby & your ECOSTONE to operate.

BLUETOOTH

When turned ON, the ECOSTONE will power on and search for your

Bluetooth. Refer to STEP 3 for details

SPEAKER

VOLUME

PRESS - to decrease the volume & PRESS + to increase the volume

NOTE: Some Bluetooth devices may require they are manually set at

max. for max. level audio

Your ECOSTONE will beep to indicate when the + button is pressed and

maximum volume setting is reached

TRACK

SELECTION

PRESS < for previous track selection & PRESS > to advance the track

selection

PLAY PAUSE

ANSWER

PRESS button once to PAUSE & PLAY song tracks and to ANSWER

mobile CALLS

LED

FLASHLIGHT

PRESS the LED button once to turn ON the flashlight. PRESS a

second time to turn OFF

TOP PANEL [on the top]

Quick Start USER GUIDE

To access the connections TURN the cap to the LEFT so the cap’s arrow point

lines up with “UNLOCKED” along the back edge of the unit.

STEP 1: Select “UNLOCKED”

STEP 2: Open Cap

Step 3: Access Connections

BACK PANEL [under the Cap] Master Power Switch & Connections

Quick Start USER GUIDE

ON OFF

MASTER

POWER

MASTER POWER ECOSTONE has a separate Master Power Switch and a Standby Button.

The Switch MUST be set to the ON position to power your ECOSTONE.

Once the Switch is set to ON, use the Standby Button located on the top panel to turn the unit ON/OFF

NOTE: When not in use for extended periods, turn the MASTER POWER OFF to preserve battery life.

IMPORTANT: STANDBY POWER function will NOT operate when the MASTER POWER is set OFF

OUTPUT

5V 1A

USB OUTPUT Connect your devices’ USB cable to connect to the USB OUTPUT (5V…1A) connection

in order to charge your device. Connect to the USB OUTPUT port to charge your personal device. Use

the USB cable included with your personal device.

NOTE: Charging rates are similar to the charging rate when connected to the USB of a desktop PC.

Typical charge time is approx. 3hrs from low to full for most Smartphones however charge times will

vary depending on the device being charged, the device’s battery specs., and the device features.

In some instances your personal device may not indicated charge is in process

CAUTION: Do NOT charge if unit and/or connections are wet or damp

INPUT

5V 1A

USB INPUT Connect your ECOSTONE to the USB micro INPUT using the USB cable to charge your

ECOSTONE

RECOMMENDATION: Use the USB cable included with the ECOSTONE.

NOTE: Typical charge time from low to full charge is up to approx. 5 hours.

NOTE: ECOSTONE can charge while playing audio. ECOSTONE can charge your device while

playing audio. Battery playtime shall be reduced depending on the time and size of the device charging

while connected to your ECOSTONE.

CAUTION: Do NOT charge if unit and/or connections are wet or damp

AUDIO

AUX IN

AUDIO AUX IN Connect an audio device using the 3.5mm cable connection on the AUDIO AUX IN as

an alternative to a Bluetooth connection to your ECOSTONE.

NOTE: Volume level must be controlled from the audio device when connected to AUX IN connection.

BACK PANEL [under the Cap] Master Power Switch & Connection Functions

Quick Start USER GUIDE

IMPORTANT:

IF the cap on the back

panel is not properly

closed, the unit is NOT

watertight.

To ensure the unit is

watertight & waterproof,

ALWAYS CLOSE the

CAP PROPERLY

TURN the cap to the

RIGHT so the cap’s arrow

point lines up with

“LOCKED” along the

back edge of the unit.

BACK PANEL [CAP CLOSED & LOCKED]

Quick Start USER GUIDE

BOTTOM VIEW: ¼” attachment point for use with

tripod stand or suction cup mounts (available separately)

FRONT VIEW: carrying handle & grill

SPECIFICATIONS

Unit Size / Weight: 3.8” x 12.3” x 7.0“/ 41 ounces Mount Attachment Point: 1/4" diameter

Output Power: RMS 24W (12 Watt x2 speakers/ 4 ohms) Frequency Range: 125Hz-18,000Hz

S/N Ratio: 88db +/- 3dB Bluetooth:

Bluetooth®

CSR 4.0

Power Source: 3.7V, 2800mAh Lithium Polymer Battery Charging Options: USB to AC adapter or Computer

Playtime: 12+ hours from full charge at 75% vol. level Charging Time: Approximately 3 hours

Recommended Storage (Battery) Temperature: 59°F / 15°C Operating Temperature: 23°F to 104°F

US Military Certification: MIL-STD 810G Dust/Waterproof Rating: IPX68

IN THE BOX

ECOSTONE unit

USB Cable

AC (5V, 1A) Wall Outlet Power Adapter

Carabineer Clip

User Guide

This product may contain chemicals listed in Proposition 65.

Quick Start USER GUIDE

FCC Compliance Statement & Warning: This device has been tested & found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. The device generates, uses & can radiate radio frequency energy & if not installed & used in accordance with

instructions may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a

particular installation IF this device causes interference to radio or television reception try one of these measures: reorient or relocate the

receiving antenna, increase separation between device & receiver, connect the device into an outlet on a circuit different from that to

which the receiver is connected, consult a dealer or experienced radio / TV technician for assistance. Changes or modifications not

expressly approved by the party responsible for compliance could void the user’s authority to operate the device and/or void the

manufacturer’s limited warranty.

Product Use and Protection: Read and Follow all Instructions. Use only as intended.

The ECOXGEAR Bluetooth speaker is intended to be used indoors or outdoors and in land or water environments. The speaker has been tested to

IPX7 waterproofing standards which means the speaker can be submerged in water up to 3 feet of water for 30 minutes without any damage.

However, the speaker is not intended for constant underwater use.

Always make sure the cap(s) / covers(s) are clean, free from sand or debris and correctly fitted. The speaker will only meet IPX7 ratings if all

rubber seals, gaskets and cover(s) / cap(s) are in place. If you notice a muffling of audio after submersion gently shake the unit to clear excess

water. If your speaker is exposed to salt water clean it thoroughly after use with fresh water.

The USB cables, power adapters and unit with in improperly fitted backdoor are NOT waterproof.

To prevent fire or shock, do not attempt to charge this unit if it is wet or you suspect water has entered the unit. In this situation, please return

the unit to Grace Digital for a free assessment. If we have found that the unit has carried water we will repair or replace the unit free of charge.

SAFETY ADVISORY & WARNING: Read and Follow all Instructions. Use only as intended.

CAUTION: Do NOT open to repair. A qualified technician must carry out repair work.

CAUTION: ATTENTION: Do NOT charge while the unit is wet. Towel dry the unit AND make sure all connections are dry BEFORE plugging in

the charging connector. Failure to do so may result in electrical damage to the unit and may void the warranty.

WARNING:

WARNING: ECOSTONE has a built-in Lithium Ion battery. The battery must NOT be used in or near an open heat source or excessive heat.

WARNING: Danger of explosion if batter is incorrectly replaced. Replace only with the same or equivalent type.

ATTENTION:

AC adaptor is a device forming a part of the main plug therefore the AC adaptor can always be readily disconnected from

AC socket-outlet.

Quick Start USER GUIDE

SAFETY

This product has a limited life span of use and should be replaced when it shows obvious signs of wear.

Do not modify or remove any original component parts of the speaker. Doing so could cause damage to the unit allowing water to ingress.

A unit with water ingress should not be charged due to potential risk of fire or shock.

Do not attempt to mount the unit except with the approved ECOXGEAR mounts. Doing so could cause damage to the unit allowing water to

ingress. A unit with water ingress should not be charged due to potential risk of fire or shock.

Please exercise care and good judgment when using your ECOXGEAR speaker. Audio levels should be appropriate to your environment, comply

with all local regulations, and always ensure that you can hear and be aware of any potential hazards around you.

You should always

1) Use the ECOXGEAR speaker in accordance with any music or noise rules and regulations.

2) Use the proper ECOXGEAR mounts if you intend to mount the unit.

3) Properly seal the ECOXGEAR prior and after each use when in humid or water environments to avoid water damage to the internal

components. Salt water / air is particular corrosive. Always make sure that the gasket are sealed when in salt water environment and the

unit properly rinsed off after use.

4) Properly clean the ECOXGEAR and ensure the gaskets have no sand, dirt or water on them prior to storage or removing the back cover.

5) Store your unit with all caps properly sealed to avoid long term internal moisture damage inside your unit.

6) Completely dry and clean your ECOXGEAR prior to attempting to charge the unit.

7) Return the ECOXGEAR to Grace Digital if you suspect water ingress into the unit or if the unit has experienced a severe impact that may

have affected the integrity of the unit to take on water.

You should never

1) Charge your ECOXGEAR if you suspect water has entered the device. Charging a device with water inside could be potential hazardous and

cause fire or a spark.

2) Use your ECOXGEAR if you have dropped it or thrown it against a hard surface which may have destroyed the integrity of the speakers,

housings or gaskets. In the event of a severe impact to your unit please return the unit to Grace Digital to review for potential damage.

3) Open the auxiliary door in a water environment. This could cause water to ingress into the unit which could potentially be hazardous and

cause a fire or a spark.

4) Connect a device to the auxiliary input jack when in a water environment. The auxiliary jack should only be used in a dry environment.

5) Attempt to fix, repair your ECOXGEAR unit. Please send it back to Grace Digital for any assessments and repairs.

Inhaltsverzeichnis

Andere EcoxGear Sprecher Handbücher

EcoxGear

EcoxGear EcoPebble Bedienungsanleitung

EcoxGear

EcoxGear ECOSTONE GDI-EGST700 Einrichtungshandbuch

EcoxGear

EcoxGear EcoEdge Pro GDI-EXEDGPRO401 Bedienungsanleitung

EcoxGear

EcoxGear EcoDrift GDI-EXDRFT200 Bedienungsanleitung

EcoxGear

EcoxGear GDI-EXBM901 Bedienungsanleitung

EcoxGear

EcoxGear MARINE FX Bedienungsanleitung

EcoxGear

EcoxGear EcoBoulder MAX GDI-EXBDR Series Bedienungsanleitung

EcoxGear

EcoxGear SOUNDEXTREME SEI-ETAMPBAT7700 20 Series Bedienungsanleitung

EcoxGear

EcoxGear EcoBoulder+ Bedienungsanleitung

EcoxGear

EcoxGear EcoCarbon GDI-EXCBN200...209 Bedienungsanleitung

EcoxGear

EcoxGear Ecopebble GDI-EGBP100-110 Bedienungsanleitung

EcoxGear

EcoxGear ECOXBT GDI-EGBT500-510 Bedienungsanleitung

EcoxGear

EcoxGear EcoExtreme 2 Bedienungsanleitung

EcoxGear

EcoxGear ECOXBT GDI-EGBT500 Bedienungsanleitung

EcoxGear

EcoxGear GDI-VXYMHFTWL01 Bedienungsanleitung

EcoxGear

EcoxGear EcoRoam 30 Bedienungsanleitung

EcoxGear

EcoxGear SOUNDEXTREME SEI-ET7700 20 Series Bedienungsanleitung

EcoxGear

EcoxGear EcoDuo GDI-EXPB2100 Bedienungsanleitung

EcoxGear

EcoxGear GDI-EXBLD800 Bedienungsanleitung

EcoxGear

EcoxGear SOUNDEXTREME SEI-ET7700 20 Series Montageanleitung

EcoxGear

EcoxGear SEI-ETAMP7700 20 Series Bedienungsanleitung

EcoxGear

EcoxGear EcoEdge Plus GDI-EXEGPL400 Bedienungsanleitung

EcoxGear

EcoxGear SOUNDEXTREME LEDCast SEI-SESPKR65 Bedienungsanleitung

EcoxGear

EcoxGear 2.5 Marine Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung