Edbak PWB1 Bedienungsanleitung

4. Security screw

When the screen is hanging securely on the back plate,

tighten solidly two security screws situated in bottom

part of front panels using Phillips screw driver.

5. Maintenance

Before maintenance of wall mount it is necessary to turn off and unplug plasma/LCD screen.

Wipe the screen up with dry cloth. If the wall mount is very dirty, it is necessary to remove the dirt first with

neutral cleaner diluted with water, and than wipe the mount up with dry cloth. You can not use such cleaners

like solvent, furniture wax as it may cause peeling off of the powdercoated metal parts.

EDBAK Sp. z o.o.

Piotrowice 186, 23-107 Strzyżewice, Poland

www.edbak.com [email protected]

Rev. date: 31.07.2006

PWB1

UNIVERSAL FIXED WALL MOUNT PWB1

FOR 32-60” PLASMA /LCD SCREENS

Installation manual

SAFETY WARNING!

Remarks regarding safety and installation

INSTRUCTIONS MUST BE ALWAYS FOLLOWED PRECISELY

1. Before installation read carefully this installation manual and instruction manual of your

plasma/LCD screen for proper installation.

2. Installation of this unit should be carried out by at least two qualified technicians.

3. This unit is not adapted to direct installation on the ceiling surface. Mounting to the ceiling is

only possible with CM1 adapter.

4. EDBAK is not liable for any damage or injury caused by mishandling or improper installation.

5. Maximum capacity load: 80 kg

6. Mounting interface: min. 100x100 mm, max 750x460mm

Universal Fixed Wall Mount PWB1

List of components:

1. Back plate – 1 pcs.

2. Front plate – 2 pcs.

3. Fixings and fixtures - 1 bag

4. Instruction manual – 1 pcs.

Tools required for installation (not

included):

- Allen key nr 3,4,5, 6 – 1 pcs.

- Phillips PH2 screwdriver – 1 pcs.

Formatiert: Schriftart: Fett

Gelöscht: Every 6 months run

periodical check the condition of

screw joints and in case there ¶

Gelöscht: .

Gelöscht: 5

Gelöscht: .

Gelöscht: ¶

1. Mounting back plate on the wall surface

Mounting of the back plate to the wall

should be carried out in desired position

after prior checking of wall type and

structure and according to building craft.

If you have any doubt please consult a

qualified builder or contractor. It is not

allowed to mount a screen on the wall

which structure is not durable enough to

hold the specified capacity load.

Mount back plate horizontally to the wall

surface using screws/bolts (not supplied) suitable to

the type and structure of wall.

2. Mounting front plates to the back of plasma / LCD screen

Place plasma/LCD screen face down on soft cloth (to prevent damage) on a flat and stable surface.

Please compile all parts necessary for mounting:

front plate – 2 pcs

screw – 4 pcs.

washer – 4 pcs.

spacer – min. 4 pcs.

In the enclosed bag there are different screws, washers and spacers fitting different types and makes of

plasma/LCD screens. Only ONE set of screws, washers and spacers will be necessary for mounting front plates

to the back of plasma/LCD screen.

Compile set of screws, washers and spacers in the following manner:

-select suitable height of spacers, in order to keep a couple millimeters distance between the back of the

plasma/LCD screen and front panels

-select suitable screws (length and thread), so that after assembling spacers, front panels and washers

together the depth mounting pole back of the plasma/LCD screen is adequate to the length of the screw

thread. Screw can not be too long, because while screwing in it may cause damage to your screen.

Position front panels centrally on the back of the screen

Tighten previously selected screws using Allen key.

3. Mounting screen on the back plate

Please be careful while engaging plasma with the

wall!!

Raise the screen in vertical position (at least two people)

with front plates already assembled to the back of the

screen and hang it on the back plate mounted on the wall

surface, so that hooks hang on the edge of the back plate

(please see the drawing).

Make sure that the hooks are hooked on the edge of the back plate.

Top

Bottom

Top of the screen

Bottom of the

screen

Screw

Washer

Front plate

Spacer

Mounting

hole

Allen key

Center holes

Screen center Formatiert: Schriftart: (Standard)

Arial

Formatiert: Schriftart: (Standard)

Arial

Gelöscht: on

Gelöscht: <sp><sp>

Gelöscht: as

Gelöscht: <sp><sp>

Gelöscht: Klucz imbusowy

Andere Edbak Rack & Stand Handbücher

Edbak

Edbak SWM150 Bedienungsanleitung

Edbak

Edbak DM141 Bedienungsanleitung

Edbak

Edbak VWPOPT65 Bedienungsanleitung

Edbak

Edbak STD03 Bedienungsanleitung

Edbak

Edbak VWPOP40 Bedienungsanleitung

Edbak

Edbak DM101 Bedienungsanleitung

Edbak

Edbak STD17 Bedienungsanleitung

Edbak

Edbak VWTA2347-L Bedienungsanleitung

Edbak

Edbak SV10 Bedienungsanleitung

Edbak

Edbak PM1 Bedienungsanleitung

Edbak

Edbak TR24 Bedienungsanleitung

Edbak

Edbak TRV200 Bedienungsanleitung

Edbak

Edbak CMS21 Bedienungsanleitung

Edbak

Edbak MBV3155-L Bedienungsanleitung

Edbak

Edbak MSV1 Bedienungsanleitung

Edbak

Edbak VSM654 Bedienungsanleitung

Edbak

Edbak STD17D Bedienungsanleitung

Edbak

Edbak MBV3147-L Bedienungsanleitung

Edbak

Edbak VSM653 Bedienungsanleitung

Edbak

Edbak TRV100 Bedienungsanleitung

Edbak

Edbak MBV2147-P Bedienungsanleitung

Edbak

Edbak PMHD115 Bedienungsanleitung

Edbak

Edbak VSM652 Bedienungsanleitung

Edbak

Edbak STD04 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung