Edc PANTHER Installationsanleitung

PANTHER

Installation and operating guide

KLIMASKLEP, ul. Orzechowa 3, 72-010 Przęsocin k/Szczecina

tel.: (91) 432-43-42, tel.: (91) 432-43-49

e-mail: sklep@klimasklep.pl, www: www.KlimaSklep.pl

PANTHER

Condensate removal pump

Installation and operating guide

The PANTHER is a self-contained

condensate removal system for use

directly inside trunking and high-

wall-mount air conditioners.The

small remote sensor can be fitted

inside the air handler whilst the

pump unit can be positioned

elsewhere.

2 3 4 5 6 71 9 10 11 12 13 148 16 17 18 19 2015

30 40 5010 60

Vertical lift

(m)

(ft)

Flow rate

(l/h)

(US gal/h))

0m Horiz

50m Horiz

100m Horiz

Capacity

Specifications

Power supply: 120/240Vac, 50/60Hz Auto sensing

Power consumption: 16W max., 0.25W when idle

Alarm relay: 5A, 30Vdc, 250Vac Break on fault

Capacity: 12 litres/hour max. (3.17 US gal/h)

Maximum head: Vertical >20m (65 ft), Horizontal >100 m (328 ft)

Suction 1 m max. (3.28 ft)

Ambient temp: 0 - 40°C

Water temp: 25°C max.

Material: Flame retardant ABS UL94 5VA

Discharge tube: 6mm (1/4”) ID

Dimensions: Pump: 135 x 46 x 32mm (5.3” x 1.8” x 1.26”)

Sensor: 45 x 36mm dia. (1.8” x 1.4” dia.)

IP: 20

SAFETY INSTRUCTIONS AND WARNING

Under normal use this equipment requires no user intervention. Installation, both fixing

and electrical, and maintenance work shall be carried out only by the manufacturer or

by its service center or in any case by a person having similar skills, so as to prevent

any risk. Electrical installation of equipment shall be in compliance with these

installation instructions and with all National and Local Regulations for Electrical Safety.

To reduce the risk of fire, electrical shock and injury to persons, the following safety

instructions shall be used:

This pump is intended for indoor use with water only (max 25°C).

This pump is NOT SUBMERSIBLE.

Disconnect ALL power supplies before starting installation, connection or

maintenance work.

This pump is provided with a grounding conductor. To reduce the risk of electric

shock, be certain that it is connected only to a properly grounded, grounding type

receptacle.

All interconnecting tubes and cables should be confined within the air conditioning

unit, or enclosed in any way

During electrical installation, make sure this condensate pump is connected to a

circuit having switch with contact separation in all poles that provide full

disconnection from the power supply under over-voltage categories III

During electrical installation, a fuse non-time delay (rated 250V 1A), shall be fitted

into the line, supply side, see electrical installation section.

The power cord is not replaceable. If the power cord is damaged then the entire

pump must be replaced.

Children should be supervised to ensure that they are not left unattended in the

area where the pump is in use.

Children or persons with reduced physical, sensory or mental capabilities which

limits their ability to use the appliance should have a responsible person to instruct

them in its use.

Do not allow any chemicals to come into contact with this pump. Remove the pump

from the system before using cleaning fluid or any other chemicals. Flush the system

with clean water before re-connecting the pump.

All fittings on this pump are designed to be finger-tight. The use of tools to attach

pipework may result in damage to the pump.

In any installations where property damage and/or personal injury might result from an

inoperative or leaking pump, it is strongly recommended that the alarm relay should be

used to operate an alarm and/or switch off the air conditioning unit.

Fig.1.

Pump outlet

Pump inlet (from sensor)

Sensor

socket

Sensor

plug

Breather tube

Breather support

Sensor

inlet

Inlet

connector

Sensor

outlet

Pump

Sensor

Operation

The PANTHER sensor will automatically start the pump when condensate is detected and

stop the pump when the condensate has been removed. The PANTHER sensor is also

fitted with a high water level alarm that will operate the alarm relay if the water level rises

to abnormal levels. The pump will continue to run until the minimum water level is reached

and then the alarm will reset.

The PANTHER sensor can be positioned in any suitable location within the equipment

below the level of the collection tray. The top of the breather tube should be positioned

above the highest level that the condensate may reach. Three typical installations are

shown below. (Fig.4) Horizontal mounting, typical of high wall mounted fan units. (Fig.5)

Angled, typical of direct mounting to collection tray. (Fig.6) Vertical, typical of cassette unit

mounting.

Fig.2.

30°30°

ü ü

Fig.3.

90°

üû

Sensor installation

The PANTHER sensor can be installed at any angle between horizontal and vertical so

long as the breather tube inlet is above the condensate inlet (Fig. 3). The PANTHER

sensor can also be tilted sideways up to 30° from horizontal (Fig. 2).

Fig.4.

Fig.5.

Fig.6.

Fig.10.

Alarm Contacts

Volt Free Break On Fault connection is

rated 5 amps 1250VA. It may be

necessary to use a contactor if the air

handler supply is to be switched.

Cable Connections

Wire Colour Connect Symbol

1 GREEN/ YELLOW EARTH E

2 BLACK LIVE L

3 WHITE NEUTRAL N

4 VIOLET Alarm contact

5 VIOLET Alarm contact

EL N

POWER SUPPLY

CONTROL

CIRCUIT

FUSE

1 2 3 4 5

Wiring Connections

Connect the ground, live and neutral wire from the supply cable of the PANTHER pump

to the supply terminals (see Fig.6)

This product must be connected using a switch with contact separation in all poles that

provide full disconnection from the power supply under over-voltage categories III. A

fuse non time delay (rated 250V 1A), shall be fitted into the line, supply side (see

Fig.10).

Pump installation

The PANTHER pump can be installed in any convenient space inside the equipment,

trunking or voids up to 1 metre above the sensor. Typical installations are shown below.

(Fig.7) Inside the air handler. (Fig.8) In a false ceiling above the air handler. (Fig.9)

Inside trunking or false wall.

Where possible the pump should be placed on or wrapped in foam insulation

and cables and tubes should be secured to reduce vibration and noise.

Fig.7. Fig.8. Fig.9.

WARRANTY

This product is guaranteed for two years to be free from manufacturing defects or faulty

materials. If it should fail for either of these reasons within two years from the date of

manufacture it will be repaired or replaced free of charge, at the option of EDC

International Limited.

EDC International Limited can accept no liability whatsoever for any loss or damage

arising from the use of this product, however caused. Before using this product the user

should satisfy himself that it is suitable for use in the intended application and for the

manner in which it is intended that it be used.

This product is subject to continuous development and improvement and EDC

International Limited reserves the right to alter the specification or design without prior

notice.

Testing

Before testing, ensure that the collection tray and drain hose is free of dirt and debris.

Pour clean tap water into the collection tray until the pump starts. Pump operation may

be noisy initially until any air has been purged from the system.

Continue to add water and the pump should switch to full power and the alarm contacts

should open. Do not continue to add water if it becomes visible in the breather tube.

Allow the PANTHER to clear the water. The pump should switch off and the alarm relay

should reset.

Pump is pumping air:

Check that the sensor is in the correct

orientation.

Check the tube between sensor and

pump.

Check that the pump outlet tube is not

syphoning.

Check sensor for dirt or mould.

Trouble Shooting

Pump does not run:

Check fuse and electrical supply connections.

Check that water is reaching the pump sensor

in sufficient quantities to start the pump.

Check the sensor connector is plugged into the

pump.

Pump is noisy:

Check that the , mains cable and

outlet tube are not vibrating against the sides of

the equipment.

Pump continues to run with no water:

The water sensor can become over sensitive if

contaminated by dirt or certain cleaning

chemicals. If this occurs the pump may

continue to run with no water. Disconnect the

sensor from the pump and flush the

sensor by pouring clean tap water into the inlet

for around 30 seconds (Fig. 11).

If the problem persists, flush with methylated

spirit and then rinse with water.

In dirty environments an in-line filter is

recommended to avoid pump and sensor

damage.

PANTHER

Fig.11.

EDC International Ltd.

Brook House, Station Road,

Pangbourne, RG8 7AN, UK

Phone: +44 (0) 118 984 2991

Fax: +44 (0) 118 984 5300

info@edcpumps.com

www.edcpumps.com

KLIMASKLEP

ul. Orzechowa 3

72-010 Przęsocin k/Szczecina

tel.: (91) 432-43-42

tel.: (91) 432-43-49

e-mail: [email protected]

www: www.KlimaSklep.pl

Inhaltsverzeichnis

Andere edc Wasserpumpe Handbücher

edc

edc COUGAR Installationsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

edc PANTHER Installationsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken