Edelbrock 5247 Bedienungsanleitung

Catalog #5247, #5248, & #5249

Brochure #63-0469

Rev. 6/06 - DA/mc

Page 1 of 2

Edelbrock Adjustable Trailing Arms

Applications: Catalog #5247 - 1978-1988 A/G Body

Catalog #5248 - 1968-1972 A Body

Catalog #5249 - 1964-1967 A Body &

1967-1978 American Motors Rebel, Matador,

Marlin, and Ambassador

Installation Instructions

Please study these instructions carefully before installing your new Adjustble Trailing Arms. If you have any questions, contact our

Technical Hotline at: 1-800-416-8628, 7 am to 5 pm, Monday-Friday, Pacific Standard Time or

e-mail us at [email protected]. Please complete and mail your warranty card.

Tools and Supplies Required:

❑ Floorjack and jackstands ❑ Drill motor and 1/2” drill bit or round file

❑Tire chocks ❑ Torque wrench

❑Lug wrench ❑ Blue Loctite™

❑18mm socket and combination wrench ❑ Grease gun

❑ 3/4” socket and combination wrench

REMOVAL OF STOCK TRAILING ARMS

1. Place car on level surface and place tire chocks in front of and behind

front tires

(Figure 1).

2. Support rear of the car on jackstands and remove the rear wheels.

3. Place a floor jack under the differential and lift up slightly to remove

tension from the trailing arm bolts - make sure not to lift the car off the

jackstands

(Figure 2).

KEEP FLOOR JACK UNDER CAR DURING THE COMPLETE REMOVAL

AND INSTALLATION PROCEDURE.

CAUTION

- DO NOT REMOVE BOTH TRAILING ARMS AT THE SAME

TIME OR THE AXLE WILL ROTATE AND THE TRAILING ARM

INSTALLATION WILL BE MUCH MORE DIFFICULT.

4. Start with either trailing arm and remove the rear bolt.

NOTE: Re-install the bolts in same direction as original.

5. Remove the front trailing arm bolt.

6. Remove the trailing arm.

7. If you are having difficulty removing the trailing arm bolts, then remove

the lower shock bolts and the rear springs to aid bolt removal.

8. Clean frame at trailing arm pivot area with a wire brush.

9. Remove the pressed-in factory rubber bushing from axle housing. Note

direction of bushing in axle housing.

NOTE: Be careful not to damage axle housing.

Fig. 1

Fig. 2

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in

poor performance and engine or vehicle damage.

Catalog #5247, #5248, & #5249

Brochure #63-0469

Rev. 6/06 - DA/mc

Page 2 of 2

INSTALLATION OF EDELBROCK ADJUSTABLE TRAILING ARMS

Edelbrock AdjustableTrailing Arms are fully assembled, greased, and ready to install.

1. Install polyurethane bushing into axle housing, facing same direction as stock.

2. Install polyurethane thrust washer on inboard side of bushing. NOTE: Left side only, some thrust washers will require trimming

for clearance to axle housing. If you install thrust washer at the same time as you install bushing, it requires less grinding for

clearance.

3. On 1978-1988 model year vehicles - using metric stock arm pivot bolts, drill or file front locating hole to 1/2” diameter to enable

use of supplied 1/2” diameter bolts.

4. Install new trailing arms with the grease fittings facing down, locating the front bolt first.

5. Place one drop of blue Loctite™ on clean threads and torque the nut to 70 ft./lbs.

6. The trailing arm should then pivot smoothly.

7. Place a thin coat of supplied grease on the sides of the new axle housing bushings.

8. Pivot trailing arm into position over polyurethane bushing and thrust washer. Install rear bolt in same direction as original.

9. Place one drop of blue Loctite™ on clean threads and torque the nut to 70 ft./lbs.

10. Although Edelbrock Trailing Arms are pre-lubed, you may want to finish your installation by lubing the front bushings with a

greasegun. Be sure to replace the dust caps on the Zerk fittings to prevent dirt and corrosion from damaging the fitting.

Check all nut and bolt tightness after first 10 miles.

NOTES:

1. Edelbrock Adjustable Trailing arms come pre-adjusted to stock length. Pinion angle can be adjusted by loosening the jam nuts

on the arms and turning the aluminum adjuster sleeve in the center of the arm. Both arms should be adjusted evenly. A properly

installed and adjusted trailing arm will have the spherical ball straight and parallel with the ball housing. If the ball is twisted in

its housing when installed, the arm could fail during suspension articulation. After adjustment has been made, use a drop of

Loctite™ on threads at jam nuts.

2. Jam nuts should be checked periodically for tightness.

3. To further enhance the handling and performance of your GM vehicle, check our catalog to find out more about Edelbrock

Suspension components such as coil springs, lower trailing arms, tubular braces, anti-hop bars, tie rod sleeves, etc. To order

our catalog, call 1-800-FUN-TEAM.

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: 1-800-416-8628

Tech Fax: (310) 972-2730

E-Mail: [email protected]

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock Victor Jr. 70067 Bedienungsanleitung

Edelbrock

Edelbrock Pro-Flo Multi-Point Bedienungsanleitung

Edelbrock

Edelbrock 3844 (65mm) Bedienungsanleitung

Edelbrock

Edelbrock 3638 Bedienungsanleitung

Edelbrock

Edelbrock 65252 Bedienungsanleitung

Edelbrock

Edelbrock 5272 Bedienungsanleitung

Edelbrock

Edelbrock Russell R09761 Bedienungsanleitung

Edelbrock

Edelbrock 71836 Bedienungsanleitung

Edelbrock

Edelbrock 1797 Kurzanleitung

Edelbrock

Edelbrock 1472 Bedienungsanleitung

Edelbrock

Edelbrock Water Pump Gasket Kit 7522 Bedienungsanleitung

Edelbrock

Edelbrock Performer-Plus 2157 Bedienungsanleitung

Edelbrock

Edelbrock 9300 Betriebsanleitung

Edelbrock

Edelbrock For 1985-1992 GM Cars and Trucks 17933 Bedienungsanleitung

Edelbrock

Edelbrock 66042 Bedienungsanleitung

Edelbrock

Edelbrock THUNDER SERIES AVS 1803 Bedienungsanleitung

Edelbrock

Edelbrock 71001 Bedienungsanleitung

Edelbrock

Edelbrock Kawasaki KFX400 Bedienungsanleitung

Edelbrock

Edelbrock 47480 Bedienungsanleitung

Edelbrock

Edelbrock 70003 Bedienungsanleitung

Edelbrock

Edelbrock 1795 Bedienungsanleitung

Edelbrock

Edelbrock 68812 Bedienungsanleitung

Edelbrock

Edelbrock 36011 Bedienungsanleitung

Edelbrock

Edelbrock 67322 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung