Edelbrock 5276 Bedienungsanleitung

Page

1 of 2

Brochure No. 63-0454

Catalog #5276

Rev. 9/07 - DA/mc

EDELBROCK LOWER TRAILING ARMS

for 2005-2008 Ford Mustang

Catalog #5276

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new Trailing Arms. If you have any questions, please

contact our Technical Hotline at: 1-800-416-8628, 7:00 am to 5:00 pm, Monday through Friday, Pacific Standard Time

or e-mail us at [email protected].

Application: Designed for 2005-2008 Ford Mustang vehicles. These trailing arms are designed to stabilize the rear

suspension, while improving suspension articulation.

Suggested Tools for Installation:

❑Jack and proper load rated jackstands ❑Blue Locktite

❑Tire chocks ❑Torque wrench

❑Lug wrench ❑Grease gun

❑18mm socket and combination wrench

1. Place vehicle on level surface and place tire chocks

in front of and behind front tires.

2. Support rear of the vehicle on the jackstands and

remove the rear wheels

(See Figure 1)

3. Place a floorjack under the differential and lift up

slightly to remove tension from the trailing arm

bolts. Make sure not to lift the vehicle off the

jackstands

(See Figure 1).

NOTE: Keep floorjack under vehicle during

the complete removal and installation

procedure.

REMOVAL OF STOCK TRAILING ARMS

Fig. 1

CAUTION: Do not remove both trailing arms

at the same time or the axle will rotate and

the trailing arm installation will be much

more difficult.

4. With parking brake released, remove clip from

parking brake cable at brake caliper. Slip cable

out of brake caliper and off of parking brake

arm. Thread cable back through trailing arm

(See Figure 2).

5. Remove trailing arm bolts and trailing arms

(See Figure 3).

6. Clean attachment points with a wire brush.

Fig. 2

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

Brochure No. 63-0454

Catalog #5276

Rev. 9/07 - DA/mc

Page

2 of 2

Edelbrock Corporation, 2700 California Street, Torrance, CA 90503

Toll-Free Tech Line: 1-800-416-8628

Tech E-Mail: [email protected]

NOTE: Edelbrock trailing arms are fully assembled,

greased, and ready to install. Install new

trailing arms with the grease fittings facing

down.

1. Install the new trailing arm by locating the front

bolt first. NOTE: Spherical ball assembly goes

toward the rear of the vehicle. Use supplied

grease on urethane bushing where bushing

contacts vehicle.

2. Place one drop of blue Loctite on clean threads

and torque the nut to 70 ft./lbs.

3. The trailing arm should then pivot smoothly on

the chassis.

4. Install OEM 14mm rear bolt at the rear of the

arm.

5. Place one drop of blue Loctite on clean threads

and torque the nut to 70 ft./lbs.

(See Figure 3).

INSTALLATION OF EDELBROCK TRAILING ARMS

6. Loop parking brake cable over Edelbrock trailing

arm. Re-attach to parking brake level and clip

to caliper bracket.

7. Although Edelbrock Trailing Arms are pre-lubed,

you may want to finish your installation by

lubing the front and rear bushings with a grease

gun. Be sure to replace the dust caps on the

zerk fittings to prevent dirt and corrosion from

damaging the fitting. Teflon grease is

recommended to lube polyurethane bushings

and a high pressure rated chassis lube works

good for the special ball end of the arm.

Re-check all nut and bolt tightness after first

10 miles.

NOTE: To further upgrade your suspension,

use other Edelbrock suspension

products such as springs, shocks,

panhard rod, sub-frame connectors,

strut tower brace.

Kit Contents

Qty.Description

❑2 Trailing Arm Assembly (#25-4078)

Fig. 3

Inhaltsverzeichnis

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock 1483 Bedienungsanleitung

Edelbrock

Edelbrock Honda/Acura B-Series 4730 Bedienungsanleitung

Edelbrock

Edelbrock 77509 Bedienungsanleitung

Edelbrock

Edelbrock 24502574 LT4 Bedienungsanleitung

Edelbrock

Edelbrock 17934 Bedienungsanleitung

Edelbrock

Edelbrock 75284 Bedienungsanleitung

Edelbrock

Edelbrock 1799 Bedienungsanleitung

Edelbrock

Edelbrock 5713 Bedienungsanleitung

Edelbrock

Edelbrock 2103 Gebrauchsanweisung

Edelbrock

Edelbrock 5266 Bedienungsanleitung

Edelbrock

Edelbrock 70403 Bedienungsanleitung

Edelbrock

Edelbrock 641563 Bedienungsanleitung

Edelbrock

Edelbrock Intake Manifolds Anwendungshandbuch

Edelbrock

Edelbrock 4742 Bedienungsanleitung

Edelbrock

Edelbrock Torker 2930 Bedienungsanleitung

Edelbrock

Edelbrock 2263 Bedienungsanleitung

Edelbrock

Edelbrock 3637 Bedienungsanleitung

Edelbrock

Edelbrock 7111 Bedienungsanleitung

Edelbrock

Edelbrock 3714 Bedienungsanleitung

Edelbrock

Edelbrock 71850 Bedienungsanleitung

Edelbrock

Edelbrock Super Victor Race Manifold 2928 Bedienungsanleitung

Edelbrock

Edelbrock 5204 Bedienungsanleitung

Edelbrock

Edelbrock 5790 Bedienungsanleitung

Edelbrock

Edelbrock 4250 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung