Edelbrock 5726 Bedienungsanleitung

EDELBROCK CAT-BACK EXHAUST SYSTEM

For 1998-2001 DODGE RAM

5.2L & 5.9L V8, 2 & 4 wheel drive

Catalog #5726

INSTALLATION INSTRUCTION

Please study these instructions carefully before installing your new Cat-Back Exhaust System. If you

have any questions or problems, contact ourTechnical Hotline at: 1-800-416-8628 from 7 am - 5 pm,

Monday through Friday, Pacific Standard Time or e-mail us at: [email protected].

SUGGESTED TOOLS FOR INSTALLATION:

3/8" ratchet set with SAE and metric sockets

9/16” and 15mm wrenches

Jackstands and jack

Liquid penetrant and rubber lubricant

DISASSEMBLY

1. Raise vehicle and support with proper jackstands for the weight, leaving the suspension hanging.

2. Use caution around hot exhaust systems to avoid burns.

3. Use penetrating oil on all nuts and bolts.

4. Remove the bolts and clamps from the system and lubricate the rubber hangers.

5. Use a long pry bar to pull the rubber hangers off of the pipe hangers.

6. Remove the old system. In some cases, you will find it easier to cut the overaxle pipe to remove

it. Note: On some vehicles, the removal of the straight pipe behind the cat-converter will not be

necessary. The new I-pipe will slip onto the outlet of the pipe that is changed onto the cat-

converter of your truck. This can be determined by laying the cat-back system out next to or

under your truck to compare length.

ASSEMBLY

1. Clamp the intermediate pipe to the catalytic converter with the 2-1/2” U-clamp and just snug them

so you can adjust the pipe easily on the catalytic. Make sure that you have engaged the stock

rubber hanger with the wire hanger welded to the pipe.

2. Slip the muffler onto the intermediate pipe with a 3” clamp on the front. The offset of the muffler

is the (rear) outlet. Snug the clamp so you can adjust the pipes.

3. Install a 3” U-clamp hanger assembly on the front of the overaxle pipe and engage it into the

stock rubber hangers as you slip it into the muffler. Snug the clamps, remove front tailpipe rubber

insulator.

4. Slip tailpipe on overaxle pipe. Install hanger strap over 3” clamp “U” bolt. See Figure 1. Snug

clamp with hanger strap and slip hanger bolt through strap and the next rubber insulator, using

supplied fender washer and nyloc nut snug hanger bolt. Remove rubber hanger toward front of

truck. Note: This hanger can be used as an adjustment point. Adjust hanger for best clearance.

5. Working from the front of the system, align and tighten each pipe from the cat-back.

6. Check for clearance to body, frame, and driveline as you tighten the system from front to rear.

7. Check for leaks and correct if any is found.

WARNING: Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any

leaks before driving!

PostScript Picture

(Edelbrock B/W Logo.eps)

KIT CONTENTS

RPM SERIES CAT-BACK EXHAUST

CATALOG #5726

Qty.Part # Description

125-3123 Intermediate Pipe

125-5505 Muffler

123-3121 Overaxle Pipe Assembly

125-3145 Tail Pipe

146-5185 2-12/” U-clamp

346-5186 3” U-clamps

123-1754 Hanger Bar

168-8550 Hex Bolt

160-9184 Nyloc Nut

133-4500 Fender Washer

Please complete and mail your warranty card. Be sure to write the mode number in the “Part #”

space.

Thank you.

WARNING: Support your vehicle with proper

jackstands or ramps rated for the total vehicle

weight. Place stands so that the rear axle is

allowed to hang free for easy system removal.

WARNING: These cat-back systems are

engineered to fit stock catalytic converters or

equivalent replacements. If your original

system has been modified, Edelbrock will not

warranty fit or performance.

Overaxle / Tail Pipe Assembly

Intermediate Pipe Assembly

Hanger

Hanger Clamp Assembly

RPM Series Muffler #5505

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock 66002 Bedienungsanleitung

Edelbrock

Edelbrock 2121 Bedienungsanleitung

Edelbrock

Edelbrock THUNDER SERIES AVS 1803 Bedienungsanleitung

Edelbrock

Edelbrock 1803 Bedienungsanleitung

Edelbrock

Edelbrock Kawasaki KFX400 Bedienungsanleitung

Edelbrock

Edelbrock 1472 Bedienungsanleitung

Edelbrock

Edelbrock 1481 Bedienungsanleitung

Edelbrock

Edelbrock 17000 Bedienungsanleitung

Edelbrock

Edelbrock 1403-1413 Bedienungsanleitung

Edelbrock

Edelbrock 15002 Bedienungsanleitung

Edelbrock

Edelbrock 3638 Bedienungsanleitung

Edelbrock

Edelbrock 63-0342 Bedienungsanleitung

Edelbrock

Edelbrock 1903 Bedienungsanleitung

Edelbrock

Edelbrock 4737 Bedienungsanleitung

Edelbrock

Edelbrock Performer-Plus 2152 Bedienungsanleitung

Edelbrock

Edelbrock Honda/Acura B-Series 4730 Bedienungsanleitung

Edelbrock

Edelbrock 2WD 350 V8 Bedienungsanleitung

Edelbrock

Edelbrock 68572 Bedienungsanleitung

Edelbrock

Edelbrock 5674 Bedienungsanleitung

Edelbrock

Edelbrock 5682 Bedienungsanleitung

Edelbrock

Edelbrock 5778 Bedienungsanleitung

Edelbrock

Edelbrock PERFORMER-PLUS 2182 Bedienungsanleitung

Edelbrock

Edelbrock 1795 Bedienungsanleitung

Edelbrock

Edelbrock 6668 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung