Edelbrock 65892 Bedienungsanleitung

Catalog #65892, #65893

Page 1 of 2 Brochure #63-65892

Rev. 9/07 - DA/mc

SHORTY HEADER

For 2006-2007 Dodge Ram Pick-Up, 1500/2500 Series,

5.7L Hemi V8, Automatic Transmission, 2WD & 4WD with I.F.S.

Catalog #65892 & #65893

INSTALLATION INSTRUCTION

Please study these instructions carefully before installing your new

Shorty Header

. If you have any questions, please contact our

Technical Hotline at : 1-800-416-8628 from 7 am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at

[email protected].

SHORTY HEADER: These components are designed as a system to improve the exhaust efficiency of the Dodge 5.7L Hemi V8 engine.

This system does not require welding for installation and retains all O.E.M. emissions equipment.

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in

poor performance and engine or vehicle damage.

Suggested Tools Needed for Installation: This vehicle has some metric fasteners.

❑3/8” rachet socket set with extensions and universal swivel sockets metric & S.A.E.

❑ Set of combination wrenches

❑ Jackstands, screwdrivers, pliers, crescent wrench, etc.

❑Liquid penetrant, (GM #1052627), anti-seize compound (GM #5613695) or available equivalent

❑Thread locking compound

SPECIAL NOTICE: This Edelbrock Shorty Header has received an Executive Order number (E.O.#) from the California Air Resources

Board (C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission equipment certification, we have included

a silver fan shroud decal to help testing personnel verify that this part is a legal replacement on the vehicle for which it is cataloged.

The adhesive-backed decal should be affixed next to the existing emission and engine specifications decal. Do not cover any part of

your original emission decal.

WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your Edelbrock Shorty

Headers. Those products can cause excessive heat and moisture buildup resulting in corrosion and failure of the system.

IMPORTANT NOTE:

When cleaning any ceramic-coated Edelbrock T.E.S., use only soap and warm water. The use of caustic solvents (i.e. gunks, etc.)

will mar or damage the ceramic-coating.

INSTALLATION INSTRUCTIONS

DISASSEMBLY

1. Disconnect negative battery cable.

2. Raise and support the vehicle with two post car hoist

(recommended) or jackstands and remove both front

wheels.

3. Remove both left and right inner fender wells and set

aside.

4. Disconnect and remove O2 sensors in the front of both

left and right catalytic converter, being careful not to

damage.

5. Unbolt exhaust pipe from stock manifolds.

RIGHT SIDE ASSEMBLY:

1. Remove heat shield from manifold.

2. Remove manifold bolts.

3. Remove stock manifold and gasket.

4. Remove the black plastic heater hose retainer clip from

the valve cover stud by pulling up until it comes off and

push heater hoses out of the way.

5. Loosen the long valve cover studs (just enough to accept

the new heat shield) with a deep 5/16” socket. Slide heat

shield stamped #25-9383 under the nuts of valve cover

studs and tighten down.

Catalog #65892, #65893

Page 2 of 2 Brochure #63-65892

Rev. 9/07 - DA/mc

KIT CONTENTS

Qty.Description Qty.Description

❑1 Manifold right side (#25-9490) (#65892) ❑2 Donut gaskets; 2”

❑1 Manifold left side (#25-9480) (#65892) ❑4 Hex capscrews; 3/8” x 2”

❑1 Manifold right side (#25-9491) (#65893) ❑17 Black hardened washer; 5/16”

❑1 Manifold left side (#25-9481) (#65893) ❑17 Lock washers; 5/16”

❑1 Heat Shield left (#25-9382) ❑4 Lock washers; 3/8”

❑1 Heat Shield right (#25-9383) ❑ 4 3/8” Hex nuts

❑ 17 Hex header bolts ❑4 3/8” Flat washers

❑2 Chrysler V8 port gaskets ❑1 Heat shield sleeve

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: 1-800-416-8628

Office: 310-781-2222

E-Mail: [email protected]

RIGHT SIDE ASSEMBLY - Continuation:

6. Place black retainer clip back on valve cover stud and

make sure the heater hoses are laying in their stock place

and out of harm’s way.

7. Place right header into position with gasket and start all

bolts, lock washers, and hardened washers. Use anti-

seize compound on all header bolts before starting. Now,

tighten evenly from the center out.

LEFT SIDE ASSEMBLY:

1. Remove heat shield from stock manifold.

2. Remove manifold bolts.

3. Remove stock manifold and gasket.

4. Install the new heat shield stamped #25-9382 in the

same manner as the right assembly (steps #4, #5, and

#6).

5. Place left header into position with gasket. With anti-

seize on bolts, start all bolts, lock washers, and hardened

washers. Tighten bolts evenly from the center out.

6. Re-install the starter.

7. Remove the bolt and separate steering shaft just above

the universal joint. Take the heat shield sleeve (supplied

in hardware kit) and slide it over the rubber below on the

steering shaft and then re-connect the shaft back

together with the universal joint and tighten.

FINAL ASSEMBLY:

1. Place donut gaskets on both left and right headers.

2. Re-attach stock exhaust pipes to both headers using

supplied hardware.

3. Re-attach O2 sensors.

4. Re-connect battery.

5. At this point, it is a good idea to look over the complete

installation to be sure nothing was missed. Check all

hydraulic, vacuum and fuel lines, and wire looms to

ensure there is adequate clearance to exhaust

components.

6. Start vehicle and bring up to normal temperature and

check for possible leaks, correct as necessary.

7. Turn engine off and let cool then re-tighten all bolts

again (do not do while hot!).Note: Periodically

check header bolts to ensure a tight seal for best

performance.

8. Re-install inner fender wells.

9. Re-install front wheels, torque to factory specifications.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock 2114 Bedienungsanleitung

Edelbrock

Edelbrock 68882 Bedienungsanleitung

Edelbrock

Edelbrock 7788 Bedienungsanleitung

Edelbrock

Edelbrock Nitrous System 70410 Bedienungsanleitung

Edelbrock

Edelbrock 1100 Bedienungsanleitung

Edelbrock

Edelbrock 71003 Bedienungsanleitung

Edelbrock

Edelbrock 68952 Bedienungsanleitung

Edelbrock

Edelbrock 68752 Bedienungsanleitung

Edelbrock

Edelbrock 70211 Bedienungsanleitung

Edelbrock

Edelbrock 641563 Bedienungsanleitung

Edelbrock

Edelbrock 5785 Bedienungsanleitung

Edelbrock

Edelbrock Russell 641540 Bedienungsanleitung

Edelbrock

Edelbrock 5680 Bedienungsanleitung

Edelbrock

Edelbrock 71883 Bedienungsanleitung

Edelbrock

Edelbrock 1472 Bedienungsanleitung

Edelbrock

Edelbrock 5791 Bedienungsanleitung

Edelbrock

Edelbrock 33503 Bedienungsanleitung

Edelbrock

Edelbrock 5056 Bedienungsanleitung

Edelbrock

Edelbrock Water Pump Gasket Kit 7522 Bedienungsanleitung

Edelbrock

Edelbrock Fe Ford 5771 Bedienungsanleitung

Edelbrock

Edelbrock 4779 Bedienungsanleitung

Edelbrock

Edelbrock 262-400 Bedienungsanleitung

Edelbrock

Edelbrock 15004 Bedienungsanleitung

Edelbrock

Edelbrock Russell 641530 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung