EdgeStar BR2000BL Bedienungsanleitung

SAFETY PRECAUTIONS

Read all of the instructions before using this appliance. When using

this appliance, always exercise basic safely precautions, including the

following:

•This appliance is designed for household use only and not for commercial use.

Do not use the appliance for uses other than that for which it is designed.

•Do not use the appliance if the power supply cord is damaged. If the power

supply cord is damaged, it must be replaced by a qualified technician.

•This unit is designed to function on 115 Volts/ 60 Hz (110/115/120 Volts

acceptable) electrical circuits.

•This appliance is not designed for children. Never allow unattended children to

use this appliance.

•Unplug the appliance if it will not be used for an extended period of time.

•Unplug the appliance prior to cleaning.

•Set the appliance on a level surface away from direct sunlight and other heat

sources.

•This appliance is designed to function optimally in room temperature

environments (mid 70°s Fahrenheit).

•Do not move the unit while it is full.

•The power supply cord must be grounded.

•Never pull the power supply cord directly to disconnect the appliance. Always pull

the plug out of the socket.

•Never lift the appliance by the power supply cord or the dispensing tap.

•Keep the power supply cord away from heating surfaces.

•Service only by authorized technicians.

•Do not immerse the appliance or its power supply cord in water or any other

liquid.

•Do not cover the appliance or place anything on it.

•Do not insert any objects into the ventilation holes.

•Only use approved CO2cylinders. Make sure you read and understand all the

procedures for the CO2 cylinders before installation.

•Cylinders contain pressurized CO2. Keep them away from heat, and store in a

dry and cool place. CO2 cylinders should always be connected to a regulator!

Failure to do so may cause an explosion resulting in possible death or injury

when the cylinder valve is opened.

•Do not dispose of empty CO2 cylinders in a fire. Never drop or throw a CO2

cylinder.

•Clean this appliance regularly, and after every keg.

•If you are replacing an older appliance with this unit, take care to remove the

door of the old appliance before throwing it away. This will alleviate the risk of

child entrapment.

INTRODUCTION

Thank you for purchasing this EdgeStar product. We are glad you choose us and

we take pride in knowing that like our products our customer service will be just

as dependable. Once you complete our easy unit set up by following the manual,

it will provide you years of great service.

We ask all of our customers to please save the original product packaging in

case you need to safely transport the unit.

To better serve you, please do the following before contacting our customer

service:

•If you received a damaged product, immediately contact the dealer that

sold you the product.

•Read and follow this instruction manual carefully to help you install, use

and maintain your product.

•Read the troubleshooting section of this manual as it will help you

diagnose and solve common issues.

•Visit us on the web at http://www.edgestar.com for product guides,

additional troubleshooting resources and up-to-date information. If you

need service, our friendly customer service representatives are available

via email at service@edgestar.com or by telephone at 1 (866) 319-5473.

For Your Records:

Please write down the model and serial number below for future

reference. Both numbers are located on the label on the back of your unit

and are needed to obtain warranty service. You may also want to staple

your receipt to this manual as it is the proof of your purchase, and is also

needed for service under your warranty.

Model Number: ___________________________

Serial Number: ___________________________

Date Purchased: ___________________________

________________________________________________________________________

UNPACKING ACCESSORIES AND INVENTORY..................4

Additional Accessories......................................4

SETTING UP YOUR REFRIGERATOR......................... 4-6

Proper Location...........................................4

Installing the Casters....................................... 5

Grounding Instructions......................................5

Understanding the Temperature Control Setting................... 5

Automatic Defrosting....................................... 5

Understanding Normal Operating Sounds....................... 6

Installing the Guardrail...................................... 6

SETTING UP YOUR BEER DISPENSER........................ 6-13

Installing the Beer Tower and Faucet........................... 6

Connecting the CO2 Cylinder to the CO2 Regulator................ 7

Installing the CO2 Cylinder Holder............................. 7

Installing the Keg Coupler –Tapping the Beer..................... 8

Setting the Correct Pressure for the CO2 Regulator.................9

Setting the Regulator....................................... 10

Dispensing the Beer and Proper Drawing Technique................ 11

Beer and Clean Glasses.................................... 11

Understanding Beer Temperature..............................12

Beer Serving Guide........................................ 13

Converting the Beer Dispenser to a Refrigerator................... 13

Cleaning and Maintaining Your Draft Beer Dispenser................13

TROUBLESHOOTING......................................14-15

LIMITED WARRANTY......................................16

TABLE OF CONTENTS

If you purchased your EdgeStar Refrigerator as a Draft Beer Dispenser, it is supplied

with all the accessories you need to install and tap a standard American Sankey Tap ½

barrel keg. This unit can also fit ¼ barrel, 1/6 barrel, and Cornelius kegs with standard

American Sankey Tap connections.

All you need to do is set up the Draft Beer Dispenser, supply the full keg of beer,

and fill the CO2 tank.

Suggested optional accessories:

Beer Dispenser Cleaning Kit

Different types of taps and regulators

And more!

For more information on compatible accessories, feel free to email

service@edgestar.com or call toll-free 866-319-5473.

•To guarantee that your Refrigerator / Draft Beer

Dispenser will last for years to come, install it in a

location where there is proper air circulation and

electrical connections.

•Keep the refrigerator away from heat and direct

sunlight.

•This refrigerator is designed for indoor use only and

should not be used outdoors.

•This refrigerator should not be placed in a built-in or

recessed area. It is designed to be freestanding.

•The following dimensions are the recommended

clearances around the beer dispenser.

Sides------------2 to 3” (76 mm)

Back---------------4 to 5” (127 mm)

UNPACKING ACCESSORIES AND INVENTORY

Proper Location

NOTE: This

appliance is

designed for

“indoor” use

only and

should not be

used outdoors

Additional Accessories

1. With the contents inside the cabinet removed set the beer dispenser on its side.

2. Insert each caster into the holes on the bottom corners of the cabinet. Screw the casters

in hand tight.

3. With all four casters tightened evenly, stand the unit in an upright position.

Note: Allow the refrigerator to stand in an upright position for 8 hours before turning on the power.

This will ensure that the coolant has settled.

•This appliance’s plug must be grounded. In the event of a malfunction or breakdown,

grounding will reduce the risk of electric shock by providing a path of least resistance for

electrical current.

•Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not

under any circumstances, cut or remove the third (ground) prong from the power cord.

Any questions concerning power and/or grounding should be directed toward a certified

electrician.

•This appliance requires a standard 110~120 volt, 60Hz electrical outlet with three-prong

ground.

•Do not use outlet adaptors if unit. No other appliance should be plugged into the same

outlet. Be sure that the plug is fully inserted into the outlet.

The temperature control is located inside the unit in the upper left-hand corner. After turning the

unit on, you must wait 24 hours for the unit to cool properly. You may then adjust the temperature

setting based on your needs and preferences.

It is not usually necessary to defrost the beer dispenser. Ice that has deposited on the evaporator

is automatically defrosted when the compressor cycles off. The defrosted water collects in the

water drip tray located on the top of the compressor in the rear of the unit and evaporates.

However, if the door is often opened or you are using the unit in a humid area, excessive ice may

build up on the evaporator. In this case, turn off the unit and allow the ice to melt once your keg is

empty. Be careful to soak up the excess water with a towel.

SETTING UP YOUR FRIDGE & BEER DISPENSER

Grounding Instructions

Understanding the Temperature Control Setting

Automatic Defrosting

Installing the Casters

•Sizzling or popping sounds occur during the automatic defrost cycle.

•Bubbling or gurgling sounds and slight vibrations are the result of the refrigerant

circulating through the cooling coils.

•Cracking or popping sounds are caused by the expanding and / or contracting of the

cooling coils during the automatic defrost cycle.

•Dripping sounds occur as ice melts from the evaporator and flows into the water

collection tray during the automatic defrost cycle.

1. Snap the guardrail into the top of the cabinet’s guardrail pilot holes.

1. Remove the cabinet plug located on the top of the unit. Firmly grasp and twist and pull

upward. (It may help to open the cabinet and push up on the cabinet plug with your hand

from inside the unit).

Note: You should store this plug in a safe place as it is required to convert the beer dispenser

into a refrigerator

2. Take the tower and untangle the tubing. From the top of the unit, feed the tubing through

the hole and into the unit.

3. Align the black adapter at the bottom of the tower with the hole in the top of the cabinet

and insert and twist the tower until it locks into place (about ¼ a turn)

4. Align the faucet handle to be parallel with the beer tower with the spigot facing downward

and screw in the faucet counter-clockwise with your hands

5. Set the plastic drip pan into place below the faucet.

Understanding Normal Operating Sounds

Installing the Beer Tower and Faucet

Installing the Guardrail

1. To install the CO2gas line tube to the regulator, attach one end of the CO2 tube, to the

hose barb connection on the CO2regulator. Secure the tube by using one of the two self-

locking red plastic snap-on clamps. With a pair of pliers or a clamp crimper, snap the red

clamp on tightly. This ensures that there are no leaks.

2. Remove the plug located at the exterior back. Save it for later in case you decide to

convert the unit into an “all refrigerator.” Run the other end of the CO2tubing through the

open hole through the inside of the cabinet.

3. Insert a washer (if provided in the kit) into the regulator to cylinder attachment nut. This

step is only required if the regulator does not have a gasket.

4. Make sure the CO2 tank is full and that the valve is closed. Now attach the CO2regulator

to the CO2cylinder by screwing the loose golden regulator nut into the CO2 cylinder

valve and tighten with an adjustable wrench.

5. To mount the CO2cylinder holder to the cabinet, simply match up the holes on the holder

with the four screws protruding out of the back of the unit, and push down to lock the

holder in place. Position the CO2cylinder in the holder in a manner that you would be

able to read the numbers on the gauges and have easy access to the shut-off valve. Note

that the CO2 cylinder holder is designed to fit CO2cylinders with up to 5 pounds in

capacity. Smaller and larger CO2cylinders are acceptable for use as well.

Connecting the CO

Cylinder to the CO

Regulator and

Installing the CO2Cylinder Holder

Warning

CO2can be dangerous! CO2cylinders contain high-pressured gas, which can be

hazardous if handled improperly. Please handle with care.

Note: your CO

cylinder is shipped empty. When you purchase your first keg of beer, have

your beer distributor fill the CO2cylinder. If they are unable to recommend a company, another

option is to look in your phone book under Fire Extinguishers or Fire and Safety Equipment;

companies that refill fire extinguishers are typically willing to to fill CO2cylinders. Although

price will vary with each market area, the average cost for filling a 5 Lb CO2gas cylinder is

$14.

Note

This section describes general CO2and keg installation. For specific

instructions, see the instructions included in the accessory box.

Your beer dispenser comes with American Sankey Tap. Before purchasing a keg, check

with your beer distributor to make sure that supplied American Sankey Tap can be used.

Many European beers require a different tap. Please contact EdgeStar customer service

online via email at service@edgestar.com or by telephone at 1-866-319-5473 for more

information.

1. To connect the keg coupler to the keg, first, make sure the pull handle on the

Sankey tap is in the “up” (diagonal) position before locking it on to the beer keg.

Insert the keg coupler into the locking neck of the beer keg and turn clockwise

1/4- turn to lock into place. Make sure that the tap has been inserted flush into

the keg.

2. Now the keg coupler is secured to the keg. Attach the remaining open end of the

CO2tube to the Sankey Tap hose barb connection. Then, secure the tube by

using the remaining self-locking red plastic snap-on-clamp. Secure with pliers or

a clamp crimper to ensure that there are no leaks.

3. Now connect the beer line (from the tower) to the American Sankey tap. When

connecting the beer line, it is very important that a washer be installed between

the nut at the end of the beer line and the Sankey Tap. Remove the blue rubber

protective cap located on top of the Sankey Tap and screw the nut with the

rubber washer on to the top of the keg coupler, hand-tighten firmly. After hand-

tightening the nut, use an adjustable wrench to tighten the nut a bit further.

4. To tap the keg, pull the Black tap handle away from the coupler and push down

until it locks into position. Listen for the “click” of the pull handle when it shifts into

the final downward position. This will open the beer and CO2 gas valves. The keg

is now tapped.

5. Carefully tilt the beer keg and rest the edge on the metal keg floor support on the

bottom of the interior cabinet. Slide the beer keg in slowly, ensuring that it is fully

inside the refrigerator. Close the door.

6. Now make sure the valve on the CO2 regulator is closed (perpendicular to the

nose). Open the valve on the CO2 tank.

7. Check the pressure gauge on the regulator. Turn the screw jutting from the

regulator until the gauge reads 12-14 PSI (for most beers).

8. Now open the valve on the regulator and make sure the PSI on the gauge is still

12-14 PSI.

Installing the Keg Coupler– Tapping the Beer

When dispensing keg draft beer, the goal is to keep the CO2level prescribed by the

brewer. Any change in the CO2level will alter the taste, pouring characteristics and

appearance of the beer.

Most breweries in the U.S. recommend a CO2 pressure between 12-14 lbs for Ale and

Lager types of draft beers. This CO2 pressure will maintain the level of carbonation

specified by the brewery.

If you are unsure what the recommended CO2 pressure is for the beer you are

dispensing, simply inquire with the company you are purchasing your kegs from. If they

do not know, they can make a quick call to the beer distributor or brewery to find out this

information for you.

If the draft beer is dispensed with too low of a pressure, the CO2 that is dissolved in the

beer will “break out” of the beer. Initially this will cause the small bubbles of broken out

CO2 to float up the beer hose which will result in foamy beer. And over time the low

pressure will result in flat beer.

If the draft beer is dispensed with too high of a pressure, over time more CO2 will be

absorbed into the beer. Initially, this will not cause any problems, but over time this will

result in over-pressurized foamy beer.

Setting the Correct Pressure for the CO2Regulator

Inhaltsverzeichnis

Andere EdgeStar Kühlschrank Handbücher

EdgeStar

EdgeStar Upright Refrigerator Bedienungsanleitung

EdgeStar

EdgeStar CRF321SS Bedienungsanleitung

EdgeStar

EdgeStar CBR1501SSOD Bedienungsanleitung

EdgeStar

EdgeStar CBR1501SLD Bedienungsanleitung

EdgeStar

EdgeStar BWC120SLD Bedienungsanleitung

EdgeStar

EdgeStar CWF1700SZ Bedienungsanleitung

EdgeStar

EdgeStar TWR121ES Handbuch

EdgeStar

EdgeStar CBR1502SG Bedienungsanleitung

EdgeStar

EdgeStar BWC121SSLT Bedienungsanleitung

EdgeStar

EdgeStar RP401MED Bedienungsanleitung

EdgeStar

EdgeStar CWR1552DD Bedienungsanleitung

EdgeStar

EdgeStar OBR900SS Bedienungsanleitung

EdgeStar

EdgeStar FP430 Bedienungsanleitung

EdgeStar

EdgeStar BR2001BL Bedienungsanleitung

EdgeStar

EdgeStar BBR901BL Bedienungsanleitung

EdgeStar

EdgeStar BR1000SS Bedienungsanleitung

EdgeStar

EdgeStar TWR120S Bedienungsanleitung

EdgeStar

EdgeStar CWR301SZ Bedienungsanleitung

EdgeStar

EdgeStar CBR902SG Bedienungsanleitung

EdgeStar

EdgeStar CWB2886FD Bedienungsanleitung

EdgeStar

EdgeStar CWR460DZ Bedienungsanleitung

EdgeStar

EdgeStar CWR361FD Bedienungsanleitung

EdgeStar

EdgeStar CWF380DZ Bedienungsanleitung

EdgeStar

EdgeStar CWF340DZ Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung

Matsui

Matsui MTT50W12E Bedienungsanleitung