Edwards FireWorks UL5W7 Bedienungsanleitung
FireWorks UL5W7
Workstation Installation
Manual
P/N 3101492-EN • REV 06 • ISS 05AUG13
Copyright © 2013 UTC Fire & Security Americas Corporation, Inc.
All rights reserved
This document may not be copied in whole or in part or otherwise
reproduced without prior written consent from UTC Fire & Security
Americas Corporation, Inc., except where specifically permitted
under US and international copyright law.
Trademarks and
patents
The FireWorks name and logo are trademarks of
UTC Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacture
r
Edwards, A Division of UTC Fire & Security
Americas Corporation, Inc.
8985 Town Center Parkway, Bradenton, FL 34202, USA.
FCC compliance This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Contact information
For contact information, see www.edwardsutcfs.com.
FireWorks UL5W7 Workstation Installation Manual i
Content
Important information iii
Chapter 1 Introduction 1
About this manual 2
About FireWorks 2
About the FireWorks UL5W7 workstation 3
Compatible devices and hardware options 7
UL 864 programming requirements 9
Chapter 2 Installation 11
Quick setup 12
Setting up a FireWorks UL5W7 workstation 13
Installing option cards 14
Logging on to the FireWorks UL5W7 workstation 15
Changing Windows logon passwords 16
Setting up monitors 16
Connecting printers 19
Connecting AC power 20
Installing the FireWorks UL5W7 workstation on a desk or
bench 22
Installing the FireWorks UL5W7 workstation in a rack 24
Control panel RS-232 wiring connections 26
Connecting digital alarm communicator receivers 29
Connecting iO Series control panels 33
Activating the FireWorks software 38
Chapter 3 Applications 39
Extending the distance between a FireWorks UL5W7
workstation and a control panel 40
EST3 to FireWorks redundant communication wiring 42
Multiple FireWorks 44
Passing commands between control panels 45
Security and access applications 48
Fire applications 48
Chapter 4 Troubleshooting 49
Fire alarm control panel to workstation communication
problems 50
Workstation hard drive failure 52
ii FireWorks UL5W7 Workstation Installation Manual
Appendix A Calculations 55
UPS sizing calculations 56
Attenuation worksheet 59
Appendix B Listing requirements 61
Listing requirements 62
Index 65
FireWorks UL5W7 Workstation Installation Manual iii
Important information
Regulatory information
This product has been designed to meet the requirements of NFPA 72 National
Fire Alarm and Signaling Code, UL 864 Standard for Control Units and
Accessories for Fire Alarm Systems, and CAN/ULC-527 Standard for Control
Units for Fire Alarm Systems.
Industry Canada information
Note: The Industry Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective,
operational, and safety requirements. Industry Canada does not guarantee the
equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection. The
customer should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations made
by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user disconnect the
equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines, and internal metallic water pipe
system, if present, are connected together. This precaution may be particularly
important in rural areas.
Caution: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as
appropriate.
Limitation of liability
To the maximum extent permitted by applicable law, in no event will UTCFS be
liable for any lost profits or business opportunities, loss of use, business
interruption, loss of data, or any other indirect, special, incidental, or
consequential damages under any theory of liability, whether based in contract,
tort, negligence, product liability, or otherwise. Because some jurisdictions do not
iv FireWorks UL5W7 Workstation Installation Manual
allow the exclusion or limitation of liability for consequential or incidental
damages the preceding limitation may not apply to you. In any event the total
liability of UTCFS shall not exceed the purchase price of the product. The
foregoing limitation will apply to the maximum extent permitted by applicable law,
regardless of whether UTCFS has been advised of the possibility of such
damages and regardless of whether any remedy fails of its essential purpose.
Installation in accordance with this manual, applicable codes, and the instructions
of the authority having jurisdiction is mandatory.
While every precaution has been taken during the preparation of this manual to
ensure the accuracy of its contents, UTCFS assumes no responsibility for errors
or omissions.
Advisory messages
Advisory messages alert you to conditions or practices that can cause unwanted
results. The advisory messages used in this document are shown and described
below.
WARNING: Warning messages advise you of hazards that could result in injury
or loss of life. They tell you which actions to take or to avoid in order to prevent
the injury or loss of life.
Caution: Caution messages advise you of possible equipment damage. They tell
you which actions to take or to avoid in order to prevent the damage.
Note: Note messages advise you of the possible loss of time or effort. They
describe how to avoid the loss. Notes are also used to point out important
information that you should read.
FireWorks UL5W7 Workstation Installation Manual 1
Chapter 1
Introduction
Summary
This chapter provides a brief introduction to the FireWorks UL5W7 workstation,
and summarizes listing requirements.
Content
About this manual 2
About FireWorks 2
About the FireWorks UL5W7 workstation 3
Front panel features 3
Rear panel features 4
Motherboard cable connections 5
PCWD3 cable connections 6
Memory configuration 7
Opening and closing the DVD drive 7
Compatible devices and hardware options 7
UL 864 programming requirements 9
Chapter 1: Introduction
2 FireWorks UL5W7 Workstation Installation Manual
About this manual
This manual is for the FireWorks UL5W7 workstation models described below.
Model Description
FWUL5W7 Workstation, Intel Core 2 Duo CPU, 500 GB hard drive, DVD drive,
4 GB RAM (8 GB max.), Windows 7 Ultimate OS
FWUL5RAIDW7 [1] Workstation, Intel Core 2 Duo CPU, 500 GB RAID 1 hard drive array,
DVD drive, 4 GB RAM (8 GB max.), Windows 7 Ultimate OS
[1] RAID 1 provides fault tolerance through disk mirroring. Two separate hard drives are used.
Both hard drives store the same data. If one drive fails, the other drive continues to operate with
all of the data intact. The total capacity of the array of drives is limited to the capacity of a single
drive. RAID 1 offers reliable data protection by providing 100% redundancy. If a drive fails, it is
easily replaced. All the data is automatically copied to the replacement drive.
This manual is for authorized and product-certified distributors who are
responsible for the installation of fire alarm equipment. It is assumed that you are
already familiar with multiplex fire alarm systems and the relevant codes and
standards.
The manual shows you how to install the hardware associated with a FireWorks
display and control system. It does not show you how to install or program the
FireWorks software.
About FireWorks
The FireWorks UL5W7 workstation and FireWorks graphical command interface
software comprises a computerized display and control system. You can use the
FireWorks UL5W7 workstation with the following:
• EST3, EST3X, and combination EST3-EST3X systems
• iO Series systems
• EST2 stand-alone systems
• IRC-3 systems
• FCC systems
FireWorks lets you use one or more display computers to monitor and control
several networks of multiplex signaling systems, and card access systems.
Chapter 1: Introduction
FireWorks UL5W7 Workstation Installation Manual 3
About the FireWorks UL5W7 workstation
Front panel features
Figure 1: Front panel features
(1) ON/OFF key switch
(2) USB connectors
(3) Trouble LED
(4) Power LED
(5) Hard drive LED
(6) DVD drive
(7) DVD drive OPEN/CLOSE button
(8) DVD drive LED
(9) Optional drive bays (not used)
(10) Air filter
(11) Front fan (Fan 2)
(12) Front fan (Fan 3)
(6)
(7)
(9)
(8)
(1) (2) (3) (4) (5)
(
11
)
(
12
)
(
10
)
Chapter 1: Introduction
4 FireWorks UL5W7 Workstation Installation Manual
Rear panel features
Figure 2: Rear panel features
(1) Power connector
(2) Mouse connector
(3) Keyboard connector
(4) USB 2.0 connectors (6X)
(5) Digital (DVI) output
See “Setting up monitors” on page 16 for
more information.
(6) Audio connectors, not used
(7) Not used
(8) Expansion slots (PCI1 to PCI3)
See “Installing option cards” on page 14
for more information.
(9) PCWD3 watchdog card (factory installed)
Note: You must add the watchdog card to
your FireWorks project.
(10) Ethernet connectors (2X), not used
(11) Rear fan (Fan 4)
(12) Analog (VGA) output
(
7
)
(
1
)
(
8
)
(
3
)
(
2
)
(
12
)
(
11
)
(9)
(
4
)
(
5
)
(
6
)
(
10
)
(
4
)
Inhaltsverzeichnis
Andere Edwards Desktop Handbücher
