EK-Quantum Vector2 Strix RTX 3080 D-RGB Bedienungsanleitung

USER GUIDE

GPU WATER BLOCK

EK-Quantum

Vector² Trio RTX 3080/90 D-RGB

This product is intended for installation by expert users only. Please

consult with a qualiﬁed technician. Improper installation may result

in damage to your equipment. EK assumes no liability whatsoever,

expressed or implied, for the use of this product or its installation. The

following instructions are subject to change without notice. Please,

read the manual carefully before starting the installation process. For

updates, you can visit our ofﬁcial website www.ekwb.com.

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning the installation

process.

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion inhibiting coolants is always

recommended for liquid cooling systems and mandatory for

nickel-plated water blocks!

Do not use pure distilled water! For best results, EK

recommends the use of EK-CryoFuel coolants!

To reach optimal performance, make sure to thoroughly

bleed the air out of your water block!

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6

NICKEL PLEXI 6

NICKEL ACETAL 7

PREPARING THE GRAPHICS CARD 8

OPTION 1: USING THE MSI GEFORCE 3080/90 SUPRIM X 8

REMOVING THE STOCK COOLER AND BACKPLATE 8

OPTION 2: USING THE MSI GEFORCE RTX 3080/90 GAMING X TRIO 9

PREPARING THE WATER BLOCK FOR INSTALLATION 10

CUTTING AND PLACING THERMAL PADS 11

APPLYING THERMAL COMPOUND 12

ATTACHING THE WATER BLOCK (Option 1: MSI GEFORCE 3080/3080Ti/3090 SUPRIM X) 12

ATTACHING THE WATER BLOCK (Option 2: MSI GEFORCE 3080/3080Ti/3090 TRIO) 14

PREPARING THE BACKPLATE 15

ATTACHING THE BACKPL ATE 17

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 17

FITTINGS AND TUBING 18

CONNECTING THE D-RGB LED STRIP 19

TESTING THE LOOP 19

WARRANTY 20

SUPPORT AND SERVICE 21

SOCIAL MEDIA 21

- 4 -

Thermal Pad F 1.0 mm (7 pcs) Thermal Pad F 2.0 mm (2 pcs) Thermal Pad G 2.0 mm (2 pcs)

120 mm

16 mm

120 mm

16 mm

120 mm

24 mm

Thermal Grease (1 pc)

BOX CONTENTS

4 mm

8 mm

10 mm

EK-Loop Multi Allen Key (1 pc)

Allen Key 2 mm (1 pc)

Allen Key 2.5 mm (1 pc)

M2.5x8 AX1 Screw (1 pc)

M3x10 AX1 Screw (1 pc)

EK-Quantum Vector2Trio RTX

3080/90 D-RGB

M2.5x4 AX1 Screw (12 pcs)

Polyamid Washer M2.5 0.5mm (12 pcs)

Standoff Ø4.5/2.5 (1 pc)

Quantum Plug (2 pcs)

Standoff M3.5-M2.5 x 11.3mm (1 pc)

EK-Plug Out Spludger Tool (1 pc)

Standoff M2.5-M3 x 6.6mm (1 pc)

Nut M2.5 (2 pcs)

EAN: 104909

EAN: 104549

- 5 -

WATER BLOCK DIMENSIONS

155 mm

142.5 mm

334.5 mm

95.8 mm

123.8 mm 27 mm

- 6 -

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

NICKEL PLEXI

- Dimensions: (LxHxW): 334.5 x 155 x 27mm

- D-RGB LED count: 18

- D-RGB cable length: 50cm

- D-RGB connector 3-pin 5V digital LED header

Position EAN Description Quantity

1104465 Coldplate (Nickel) 1

2103971 Acetal Stand Out 1

3104471 LED Cover 1

4100663 EK - Badge 2

5103964 Mylar sticker 2

68208 Screw M3x8 7991DIN 2

7101556 LED D-RGB strip 500/300mm 1

8103947 FC Terminal 1

9104468 Top plate (Plexi) 1

10 104475 Backplate (Bl. elox) 1

11 103942 Terminal Badge 1

12 104216 Disc magnet 3x3 2

13 8311 Screw M4x20 DIN7984 3

14 104106 Terminal OR - 14x1 mm 2

15 103987 Standoff M3.5-M2.5 x 3 7

16 103988 Standoff M4-M2.5 x 3mm 4

17 103986 Standoff M3.5-M2.5 x 11.3mm 4

18 104187 Screw M2.5x8 AX1 7

19 104188 Standoff ﬁ 4.5/2.5 7

20 9024 Screw M4x10 DIN7984 13

21 103962 Plexi isert 1

22 104484 Main O-ring 162x2 1

23 104902 PCB cardboard 1

- 7 -

NICKEL ACETAL

- Dimensions: (LxHxW): 334.5 x 155 x 27mm

- D-RGB LED count: 38

- D-RGB cable length: 50cm

- D-RGB connector 3-pin 5V digital LED header

Position EAN Description Quantity

1104465 Coldplate (Nickel) 1

2103974 Acetal Stand out 1

3100663 EK - Badge 2

4104211 Mylar sticker 2

58202

Screw M3x12 DIN7991

6103947 FC Terminal 1

7103968 Light guide 1

8104469 Acetal top plate 1

9104475 Backplate (Bl.elox) 1

10 103942 Terminal Badge 1

11 104216 Disc magnet 3x3 2

12 8311 Screw M4x20 DIN7984 3

13 104106 Terminal OR - 14x1 mm 2

14 103987 Standoff M3.5-M2.5 x 3 7

15 103988 Standoff M4-M2.5 x 3mm 4

16 103986 Standoff M3.5-M2.5 x 11.3mm 4

17 104187 Screw M2.5x8 AX1 7

18 104188 Standoff ﬁ 4.5/2.5 7

19 9024 Screw M4x10 DIN7984 13

20 103962 Plexi insert 1

21 104296

LED D-RGB Dense Strip Double - 500/130mm

22 104484 Main O-ring 162 x 2 mm 1

23 104902 PCB cardboard 1

- 8 -

PREPARING THE GRAPHICS CARD

For this Step, you will need:

Phillips Head Screwdriver

STEP 1

REMOVING THE STOCK COOLER AND BACKPLATE

Place your graphics card on the ﬂat surface and carefully remove

the stock cooler. Do not forget to unplug all the LED and fan

connectors. Pay attention to the following steps in order to install

the EK-Quantum Vector2Trio RTX 3080/90 D-RGB water block on

the graphics card.

Use the Phillips head screwdriver to remove the ﬁve (5) green marked

screws from the GPU bracket side.

Then remove the fifteen (15) red marked screws with Phillips

head screwdriver and carefully detach the stock backplate from

the PCB. After removing the stock backplate remove four (4) blue

marked screws on retention bracket and you can move to step 2

of the process.

Always remove the stock cooler slowly - it might be ﬁrmly

glued to the PCB with thermal pads.

OPTION 1: USING THE MSI GEFORCE 3080/90 SUPRIM X

STEP 1

- 9 -

For this Step, you will need:

Phillips Head Screwdriver

STEP 1

Place your graphics card on the ﬂat surface and carefully remove the

stock cooler. Do not forget to unplug all the LED and fan connectors.

Pay attention to the following steps in order to install the EK-Quantum

Vector2Trio RTX 3080/90 D-RGB water block on the graphics card.

Use the Phillips head screwdriver to remove the three (3) green

marked screws from the GPU bracket side.

Then remove the ﬁfteen (15) red marked screws with Phillips head

screwdriver and carefully detach the stock backplate from the PCB.

After removing the stock backplate remove four (4) blue marked

screws on retention bracket and you can move to step 2 of the process.

Always remove the stock cooler slowly - it might be ﬁrmly

glued to the PCB with thermal pads.

OPTION 2: USING THE MSI GEFORCE RTX 3080/90

GAMING X TRIO

STEP 1

- 10 -

BACK PL ATE

PREPARING THE WATER BLOCK FOR INSTALLATION

STEP 1

Unscrew seven (7) Screws AX1 M2.5x8 as shown in the image.

Remove the backplate together with seven (7) Screws AX1 M2.5x8

and backplate standoffs. Standoffs must stay on Screws AX1

M2.5x8. Remove cardboard. Save the backplate set for later steps.

Do not remove standoffs from screws! In case the

standoff detaches from the screw, replace it with a

spare one. When replacing the standoff make sure

that you screw it on the AX1 M2.5x8 screw. Do not

push the standoff onto the screw AX1 M2.5x8!

STEP 1

For this step, you will need:

Phillips Head Screwdriver

M2.5 x 8 AX1

BACK PL ATE

STAN DO FF

DO NOT

REMOVE

STANDOFFS

FROM

SCREWS!

CARDBOARD

Andere Handbücher für Vector2 Strix RTX 3080 D-RGB

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere EK-Quantum Computerhardware Handbücher

EK-Quantum

EK-Quantum Vector2 Arc A750-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Reflection2 7000D D5 PWM D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Vector FTW3 RTX 3080 Bedienungsanleitung

EK-Quantum

EK-Quantum Vector2 FTW3 RTX 3080 D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Impulse 120mm FAN Bedienungsanleitung

EK-Quantum

EK-Quantum Velocity 2 D-RGB AM4 Bedienungsanleitung

EK-Quantum

EK-Quantum Reflection Fractal ATX D5 PWM D-RGB - Plexi Bedienungsanleitung

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Velocity2 D-RGB -LGA 1700 Bedienungsanleitung

EK-Quantum

EK-Quantum Reflection PC-O11D Mini D5 PWM D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Velocity2 D-RGB -LGA 1700 Bedienungsanleitung

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Vector Master RTX 4090 D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Vector FE RTX 3070 Ti D-RGB + Backplate Bedienungsanleitung

EK-Quantum

EK-Quantum Vector RX 6800/6900 D-RGB - AMD Radeon... Bedienungsanleitung

EK-Quantum

EK-Quantum Vector Strix RTX 3080 D-RGB Bedienungsanleitung

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung