Ekinex EK-BB1-TP Bedienungsanleitung

KNX-IP Interface Product code: EK-BB1-TP

KNX-IP Router Product code: EK-BC1-TP

KNX device with interface function to connect to the LAN

for programming and/or supervision of the KNX bus

system.

With IP Router version it is possible to connect multiple

KNX bus lines through the LAN with a two-way

communication. Suitable for KNX installations for control

of houses and buildings.

Description

The Ekinex® EK-BB1-TP IP interface realizes the

bidirectional data link between a PC or laptop and a KNX

system via LAN. The interface supports IP tunneling

protocol and enables addressing, setting parameters,

viewing and diagnosis of KNX devices via ETS. The

device has an integrated KNX bus communication

module and is designed for 35mm rail mounting. Power is

supplied via the KNX bus.

The Ekinex® EK-BC1-TP IP router realizes the

bidirectional data link between a PC or laptop and a KNX

system via LAN. The interface supports IP tunneling

protocol and enables addressing, setting parameters,

viewing and diagnosis of KNX devices via ETS.

The IP router also integrates the function of a line

coupler; telegrams can be exchanged between TP bus

lines through a bridge over TCP/IP. The device has an

integrated KNX bus communication module and is

designed for 35mm rail mounting.

Four LEDs show with precision the status of both KNX

and Ethernet bus lines; this helps to find common

communication problems caused to bus overload or

multiple transmission on both lines.

The device is powered by a 30 Vdc SELV voltage via the

KNX bus and does not require auxiliary power but, when

sizing the bus line, you need to consider this as a supply

equivalent to 4 devices of 10 mA.

Function

•Line coupler

•KNX bus status

•Ethernet bus status

•IP router sends telegrams from / to KNX from / to IP

network

•Programmable plant via software ETS® remotely (IP

router)

Main characteristics

•Housing in plastic material

•Mounting on 35 mm rail (according to EN 60715)

•Protection degree IP20 (according to EN 60529)

•Safety class II

•Weight 70 g

•2 modular units (1 unit = 18 mm)

•Dimensions 36 x 90 x 70 mm (WxHxD)

Technical data

Connections

•30 Vdc from KNX bus line

•Current consumption (from main bus line): about 38

•RJ45 ethernet connector

Environmental conditions

•Operating temperature: - 5 ... + 45°C

•Storage temperature: - 20 ... + 60°C

•Transport temperature: - 20 ... + 60°C

•Relative humidity: 5 - 95% not condensing

Switching, display and connection elements

The line/area coupler is equipped with 4 LEDs and a

function pushbutton located on the front of the device, 1

bus terminal for KNX bus line, 1 RJ45 connector for

Ethernet LAN, a programming LED and a programming

pushbutton.

TP1

Datasheet STEKBBC1TP_EN

REAEKBBC1TP

DCEKBBC1TP

1.LAN status LED

2.KNX status LED

3.LAN traffic LED

4.KNX traffic LED

5.Not used

6.Not used

7.Programming LED

A. Ethernet connector

B. Function pushbutton

C. Programming pushbutton

D.KNX bus connector

Command elements

•Function pushbutton (B)

- Long press (3 seconds): switch to manual control.

The default function is set with LAN line and KNX

line parameters through ETS.

- Very long press (15 seconds): all LEDs are red.

Release button and press again for some seconds:

resets all the parameter to factory default (incl.

physical address).

Display elements

•LAN status LED (1)

- off: LAN error or line not connected

- on (green): LAN normal operation

- on (red): manual override active

•KNX status LED (2)

- off: KNX error or line not connected

- on (green): KNX normal operation

•LAN traffic LED (3)

- off: no data exchange on LAN line

- blinking (green): data exchange active on LAN

- blinking (red): LAN transmission error

•KNX traffic LED (4)

- off: no data exchange on KNX line

- blinking (green): data exchange active on KNX

- blinking (red): KNX transmission error

Mounting

The device has degree of protection IP20, and is

therefore suitable for use in dry interior rooms. The

housing is made for rail mounting according to EN 60715

in boards or cabinets for electrical distribution. The

installation is in horizontal position; the correct position is

when the KNX bus terminals are located at the bottom.

For the installation of the device on the rail proceed as

follows:

•with the aid of a tool bring the locking device in the fully

lowered position (1);

•place the upper edge of the rear inner profile on the

•upper edge of the rail (2);

•rotate the device towards the rail (3);

•push the locking device upward until it stops (4).

Before removing the device, be sure the bus terminals

have been extracted from their slots. Use a screwdriver

to slide down the locking device and remove the device

from the rail.

Note. When mounting the device in boards and cabinets it

shall be provided the necessary ventilation so that the

temperature can be kept within the operating range of the

device.

Connection of the KNX bus line and LAN

The connection to the KNX bus line is made by the

terminal blocks (black/red) included in the supply and

inserted into the slots located on the bottom part of the

front.

The connection to the LAN line is made via the RJ45

terminal connected to an Ethernet cable (minimum

category 5E –not supplied).

Warning! In order to supply the KNX bus line, use

only a KNX bus power supply (e.g. ekinex EK-

AB1- TP or EK-AG1-TP). The use of other power

supplies can compromise the communication

and damage the devices connected to the bus.

Characteristics of the KNX terminal block

•Spring clamping of conductors

•4 seats for conductors for each polarity

•Terminal suitable for KNX bus cable with single-wire

conductors and diameter between 0.6 and 0.8 mm

•Recommended wire stripping approx. 5 mm

•Color codification: red = + (positive) bus conductor,

black = - (negative) bus conductor

Warning! The electrical connection of the device

can be carried out only by qualified personnel.

The incorrect installation may result in electric

shock or fire. Before making the electrical

connections, make sure the power supply has

been turned off.

IGEKBBC1TP

DCEKBBC1TP

Configuration and commissioning

Configuration and commissioning of the device require

the use of the ETS® (Engineering Tool Software)

program V5 or later releases. These activities must be

carried out according to the design of the building

automation system done by a qualified planner.

Configuration

For the configuration of the device parameters the

corresponding application program or the whole ekinex®

pro- duct database must be loaded in the ETS program.

For detailed information on configuration options, refer to

the application manual of the device available on the

website www.ekinex.com.

Note. The configuration and commissioning of KNX

devices require specialized skills. To acquire these

skills, you should attend the workshops at KNX cer-

tified training centers.

Commissioning

For commissioning the device the following activities are

required:

•make the electrical connections as described above;

•turn on the bus power supply;

•switch to programming mode by pressing the

programming pushbutton located on the front side of the

housing. During this operating mode, the programming

LED is turned on;

•download into the device the physical address and the

configuration with ETS® program.

At the end of the download the operation of the device

automatically returns to normal mode; in this mode the

programming LED is turned off. Now the bus device is

programmed and ready for use.

Dimensions [mm]

Marks

•KNX

•CE: the device complies with the Low Voltage Directive

(2006/95/EC) and the Electromagnetic Compatibility

Directive (2004/108/EC).

Maintenance

The device is maintenance-free. To clean it use a dry

cloth. It must be avoided the use of solvents or other

aggressive substances.

Disposal At the end of its useful life the product

described in this datasheet is classified as

waste from electronic equipment in

accordance with the European Directive

2002/96/EC (RAEE), and cannot be

disposed together with the municipal

undifferentiated solid waste.

Warning! Incorrect disposal of this product may

cause serious damage to the environment and

human health. Please be informed about the

correct disposal procedures for waste collecting

and processing provided by local authorities.

Documentation

This datasheet refers to the release A1.0 of the ekinex®

devices EK-BB1-TP and EK-BC1-TP, and is available for

download at www.ekinex.com as a PDF (Portable Data

Format) file.

Warnings

•Installation, electrical connection, configuration and

commissioning of the device can only be carried out by

qualified personnel in compliance with the applicable

technical standards and laws of the respective

countries;

•Opening the housing of the device causes the

immediate end of the warranty period;

•In case of tampering, the compliance with the essential

requirements of the applicable directives, for which the

device has been certified, is no longer guaranteed;

•ekinex® KNX defective devices must be returned to the

manufacturer at the following address: EKINEX S.p.A.

Via Novara 37, I-28010 Vaprio d’Agogna (NO) Italy

Otherinformation

•This datasheet is aimed at installers, system integrators

and planners

•For further information on the product, please contact

the ekinex® technical support at the e-mail address:

support@ekinex.com or visit the website

www.ekinex.com

•Each ekinex® device has a unique serial number on the

label. The serial number can be used by installers or

system integrators for documentation purposes and has

to be added in each communication addressed to the

EKINEX technical support in case of malfunctioning of

the device

•KNX® and ETS® are registered trademarks of KNX

Association cvba, Bruxelles.

this documentation without notice.

Filename

Device release

Update

STEKBBC1TP_EN.pdf

A1.0

01 / 2016

DQEKBBC1T

Code

Application program (## = release)

EK-BB1-TP

APEKBB1TP##.knxproj

EK-BC1-TP

APEKBC1TP##.knxproj

Dieses Handbuch passt für folgende Modelle

Andere Ekinex Netzwerk-Router Handbücher

Ekinex

Ekinex SIGNUM EK-EV2-TP Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung