Ekwb EK-FB MSI X399 GAMING RGB Monoblock Bedienungsanleitung

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on February 1st 2018

REMOVING STOCK COOLER. Remove all encircled screws. There are 2 (two) screws

on the back of the motherboard that need to be removed in order to remove the

factory installed MOSFET cooling solution.

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual thoroughly before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of MSI X399 GAMING PRO CARBON AC motherboard

BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.

STEP 2: PREPARING YOUR MOTHERBOARD

STEP 3: PREPARING YOUR MOTHERBOARD

APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat spreader

(IHS) - see sample photo below with enclosed thermal grease.

The quantity of about two stripes is just about right. There is no need to cover the

whole IHS. Applying too much thermal grease will have negative impact on the cooling

performance!

STEP 4: CUTTING THERMAL PADS

STEP 5: PREPARING THE MONOBLOCK

Your block comes with thermal pads which needs to be trimmed in order to fit the

voltage regulation area (MOSFET) on the motherboard’s circuit board. WARNING:

DIMENSIONS ON PICTURES BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD G 1mm - (120x24mm) [EAN: 3830046996770]

Place the M2,5 self-adhesive PVC washers under marked standoffs!

Installation manual for EK-FB MSI X399 GAMING RGB Monoblock water block

Mosfets

CPU socket

AMD X399

Chipset

1. Thermal pad G–1.0mm

(for mosfets and inductor coils):

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on February 1st 2018

Place thermal pads on PCB as shown on the picture below.

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL

PADS PRIOR TO INSTALLATION!

STEP 6: PLACING THERMAL PADS

STEP 7: PLACING A BLOCK ON TO THE MOTHERBOARD

Place the EK-FB MSI X399 RGB Monoblock gently to the motherboard or vice versa (as

shown on photo below). Make sure that mounting holes are aligned.

STEP 8.1: ATTACHING A BLOCK ON TO THE MOTHERBOARD

STEP 8.2: ATTACHING A BLOCK ON TO THE MOTHERBOARD

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block. Secure top 4 (four)

nickel screws with enclosed 2,5mm Allen key. Tighten screws diagonally and evenly

till the end of the thread. Do not use excessive force when tightening the screws!

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block. Use 2 (two) M2,5x5 AX1

screws with M2.5 PVC washers. Tighten the screws evenly. Do not use excessive force

when tightening the screws!

STEP 9: CONNECTING THE RGB LED STRIP (optional)

Plug the 4-pin connector from Monoblock RGB LED strip to the JLED1 header on your

motherboard. Please ensure that the arrow indicated on the connector is plugged

into the 12v line as indicated on your motherboard. Failure to do so will damage your

motherboard or LED strip.

For the EK-FB MSI X399 RGB Monoblock series water block to operate properly the

lower G1/4 port of the water block MUST BE USED AS THE INLET PORT. EK

recommends the use of EK-ACF fittings. When using fittings other than EK-ACF series

please use hose clamps or appropriate substitute to secure the tubing to the barb. The

use of biocide containing and corrosion inhibiting coolant is always recommended for

any liquid cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver Allen key

M2.5x5 screws

Place 1mm thermal pads in

large strip over marked area

and make sure all mosfet chips

and inductor coils are covered.

M2.5 PVC

washers

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

Dieses Handbuch passt für folgende Modelle

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB Bedienungsanleitung

ekwb

ekwb EK-FB GA X299 GAMING Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX Ti WF3 Handbuch

ekwb

ekwb EK-FC6990 Handbuch

ekwb

ekwb EK-UNI RAD Handbuch

ekwb

ekwb EK-FB KIT ASUS R4BE Leitfaden

ekwb

ekwb EK-FC690 GTX Backplate Handbuch

ekwb

ekwb EK-FC R9-290X Handbuch

ekwb

ekwb EK-FB GA Z87X-OC Force Leitfaden

ekwb

ekwb EK-Classic Pump Reservoir 160 SPC PWM D-RGB Leitfaden

ekwb

ekwb EK-FC R9-295X2 Leitfaden

ekwb

ekwb EK-Quantum Vector FE RTX 3080 Bedienungsanleitung

ekwb

ekwb EK-Quantum Velocity 2 Bedienungsanleitung

ekwb

ekwb Velocity Bedienungsanleitung

ekwb

ekwb EK-FC970 GTX TF5 Handbuch

ekwb

ekwb SLIM 120 Bedienungsanleitung

ekwb

ekwb EK-AIO 280 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FB ASUS R4BE Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC4890CF Leitfaden

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung

ekwb

ekwb EK-FC1080 G1 GTX Backplate Leitfaden

ekwb

ekwb EK-FC7950 Handbuch

ekwb

ekwb EK-FC1080 GTX G1 Bedienungsanleitung

ekwb

ekwb EK-FC560 GTX Handbuch

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

ekwb EK-FB MSI X399 GAMING RGB Monoblock Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken