Ekwb EK-Quantum Kinetic TBE 120 VTX PWM Bedienungsanleitung

INSTALLATION MANUAL

PUMP & RESERVOIR COMBO

EK-Quantum

Kinetic TBE 120/160 VTX PWM

- 2 - - 3 -

BOX CONTENT

EK-Quantum

Kinetic TBE 120/160 VTX

PWM D-RGB Allen Key 2 mm

Allen Key 2.5 mm

M4 PVC Washers (5 pcs)

M4x4 DIN7984 Screws

(5 pcs)

Gasket 10x1

Inl et Tub e EK-Loop Multi Allen Key

(6 mm, 8 mm, 9 mm)

MOUNTING MECHANISM

- 4 - - 5 -

Sealing Gasket

EK-Quantum

Kinetic TBE 120/160 VTX PWM

VTX Pump

M4 VTX Screw

Vibration Damper

EK-Quantum Kinetic TBE VTX can be used in any mounting

conﬁguration (position) apart from being mounted upside-down.

Mounting the pump upside-down may result in the pump

running dry and eventually lead to its failure!

INSTALLING THE ASSEMBLY

EK-Quantum

Kinetic TBE VTX

Pump Bracket

- 6 - - 7 -

EK-Quantum

Kinetic TBE VTX

Pump Bracket

PVC Washer

1. Installing the EK-Quantum Kinetic TBE 120/160

VTX combo unit using the EK-UNI Pump Bracket

(sold separately):

M4 X 4 Screw DIN 7984

Pump bracket -

Vertical

Using the Vertical EK-UNI Pump Bracket (sold separately):

PVC Washer

M4 X 4 Screw DIN 7984

EK-Quantum

Kinetic TBE VTX

- 8 - - 9 -

2. Installing the EK-Quantum Kinetic TBE 120/160

VTX combo unit directly into the chassis:

The assembly can be mounted on any flat surface

inside your computer chassis. You must drill 4 (four)

4.2mm holes using the power drill in a 50 x 50mm

square pattern.

Please follow these steps:

- Drill four (4) 4.2 mm holes into the chassis

- Use enclosed M4 x 4 mm screws and PVC washers to

secure the reservoir to the chassis

CAUTION:

Mounting holes pattern is not in a 1:1 scale.

- 10 - - 11 -

USING TOP PORT AS INLET

Internal Tube

EK-Quantum

Kinetic TBE VTX

Fittings must be placed on the Top port before installing the

Internal tube! In other scenarios, you can damage the Top.

EK-Quantum Kinetic TBE 160 VTX combo unit:

The internal tube, which is enclosed in a mounting Kit,

can be used for ﬂuid intake into the reservoir. Make sure

the sealing gasket on the internal tube is placed correctly.

EK-Quantum Kinetic TBE 120 VTX combo unit:

In the case of 120 Version, please follow these steps:

- Unscrew the reservoir and take off the pre-installed

Anticyclone

Remove the top part of the reservoir and attach the

internal tube on one of the three (3) G1/4 holes (make sure

that sealing gasket on the internal tube is placed correctly)

- Secure the top to the reservoir and make sure that all

gaskets are set appropriately.

CAUTION (120 version):

Using the internal tube and pre-installed Anticyclone at

the same time is strongly not recommended! This can

damage the Anticyclone!

EK-Fitting

- 12 - - 13 -

ATTACHING THE FITTINGS

INLET

(One must be used)

OUTLET

EK-Plugs

G1/4

EK recommends you use the EK-Quantum Torque

ﬁttings with EK-Quantum Kinetic TBE VTX series

combo units. If you opt for barbs, make sure that tubes

are securely attached using the hose clamps or an

appropriate substitute.

All unused ports should be blocked with enclosed

G1/4 plugs.

CAUTION:

The OUTLET port must always be placed on the marked spot.

Ports on the top of the reservoir should only be used as

INLET ports with the enclosed Internal tube.

The INLET (suction) ports are those with the G1/4

threading plane.

Make sure not to use ﬁttings or barbs longer than 5mm

with the G1/4 thread!

- 14 - - 15 -

CONNECTING THE PUMP

The EK-VTX Pump has two connectors:

1. 4-Pin Molex – must be connected directly to your

PSU at all times as it is used to power the pump;

2. 4-Pin PWM Fan – can be connected to your

motherboard CPU Fan or designated water pump

header. It can also be connected to a controller. This

cable is used to control and report the rotational

speed of the pump. If it’s not connected, the pump

will run at maximum speed (100% PWM).

4-Pin Molex

connector 4-Pin PWM

fan connector

- 16 - - 17 -

Plug the 3-pin connector from the EK-Quantum Kinetic

TBE VTX to the D-RGB header on the motherboard. . The

LED will work if the pin layout on the header is as follows:

+5V, Digital, Empty, Ground.

Please ensure that the arrow on the connector

is plugged into the +5V line, as indicated on

your motherboard.

Failure to do so will damage your motherboard or the

LED strip.

CONNECTING THE D-RGB LIGHTS

D-RGB Header

RGB Header

- 18 -

TESTING THE LOOP

To make sure the installation of EK components was

successful, we recommend you perform a leak test for

24 hours.

When your loop is complete and ﬁlled with coolant,

connect the pump to a PSU outside of your system. Do

not connect the power to any other components!

Turn on the PSU and let the pump run continuously. It is

normal for the coolant level to drop during this process

as air collects in the reservoir.

Inspect all the parts of the loop, and in the case of coolant

leaks, ﬁx the issue and repeat the testing process. Ensure

that all hardware is dry before the system is powered on

in order to prevent any damage.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ekwb Computerhardware Handbücher

ekwb

ekwb 115 Series Bedienungsanleitung

ekwb

ekwb EK-Thermosphere Leitfaden

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FB ASRock X299 RGB Monoblock Bedienungsanleitung

ekwb

ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB Bedienungsanleitung

ekwb

ekwb EK-Quantum Velocity 2 D-RGB AM4 Bedienungsanleitung

ekwb

ekwb EK-FC285 GTX Classified Handbuch

ekwb

ekwb EK-FC680 GTX SOC water block Leitfaden

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung

ekwb

ekwb EK-D5 Dual TOP CSQ Handbuch

ekwb

ekwb EK-FC WX9100 PRO BACKPLATE Bedienungsanleitung

ekwb

ekwb Classic D-RGB S240 Bedienungsanleitung

ekwb

ekwb EK-Reservoir Combo DCP 2.2 Handbuch

ekwb

ekwb EK-Pro RTX A5000 Bedienungsanleitung

ekwb

ekwb EK-FC5x0 GW GTX water block Handbuch

ekwb

ekwb EK-Quantum Vector FTW3 RTX 3070 Bedienungsanleitung

ekwb

ekwb EK-FC460 GS/SONIC Handbuch

ekwb

ekwb EK-FC Titan X Original CSQ Handbuch

ekwb

ekwb EK-FC R9-295X2 Handbuch

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Leitfaden

ekwb

ekwb EK-Quantum Reflection PC-O11D XL D5 PWM... Bedienungsanleitung

ekwb

ekwb EK-UNI Holder D5 V3 Handbuch

ekwb

ekwb EK-Pro GPU WB RTX 8000 - Ni + Inox Bedienungsanleitung

ekwb

ekwb EK-RAM Dominator Handbuch

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

ekwb EK-Quantum Kinetic TBE 120 VTX PWM Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken