Ekwb EK-FB ASRock X299 RGB Monoblock Bedienungsanleitung

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.1. Published on February 21st 2018

REMOVING STOCK COOLER. Remove all encircled screws. There are 2 screws on

the back of the motherboard that need to be removed in order to remove the

factory installed MOSFET heat pipe cooling solution.

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual thoroughly before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASRock X299 Taichi motherboard

BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.

STEP 2: PREPARING YOUR MOTHERBOARD

STEP 3: PREPARING YOUR MOTHERBOARD

APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat spreader

(IHS) - see sample photo below with enclosed thermal grease.

The quantity of about two stripes is just about right. There is no need to cover the

whole IHS. Applying too much thermal grease will have negative impact on the cooling

performance!

STEP 4: CUTTING THERMAL PADS

Your block comes with thermal pads which needs to be trimmed in order to fit the voltage regulation area (MOSFET) on the motherboard’s circuit board. WARNING:

DIMENSIONS ON PICTURES BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD G 1mm - (120x24mm) [EAN: 3830046996770]

Installation manual for EK-FB ASRock X299 RGB Monoblock water block

Mosfets

CPU socket

AMD X299

Chipset

1. Thermal pad G–1.0mm

(for mosfets and inductor coils):

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.1. Published on February 21st 2018

Place thermal pads on PCB as shown on the picture below.

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION!

STEP 5: PLACING THERMAL PADS

STEP 6: PLACING A BLOCK ON TO MOTHERBOARD

STEP 7: ATTACHING A BLOCK ON TO THE MOTHERBOARD

Place the EK-FB ASRock X299 RGB Monoblock series water block gently to the

motherboard or vice versa (as shown on photo below). Make sure that mounting

holes are aligned. Place it on factory installed washers on the motherboard (MOSFET

area).

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block.

A) Mosfet part: Use two M2,5x5 AX1 screws with M2,5 PVC washers. Tighten the

screws evenly. Do not use excessive force when tightening the screws!

B) CPU part: Use four thumb nuts with screws and M3 PVC washers. Tighten

the thumb nuts.

Use the enclosed screws and washers as shown in picture below:

STEP 8: CONNECTING THE RGB LED STRIP (optional)

Plug the 4-pin connector from Monoblock RGB LED strip to the motherboard. Please

ensure that the arrow indicated on the connector is plugged into the 12v line as

indicated on your motherboard. Failure to do so will damage your motherboard or

LED strip.

For the EK-FB ASRock X299 RGB Monoblock series water block to operate properly the

G1/4 port nearest to the right edge of the water block MUST BE USED AS THE INLET

PORT. EK recommends the use of EK-ACF fittings. When using fittings other than EK-

ACF series please use hose clamps or appropriate substitute to secure the tubing to

the barb. The use of biocide containing and corrosion inhibiting coolant is always

recommended for any liquid cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver Allen key

M2.5x5 screws

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

Place 1mm thermal pads in large strip over

marked area and make sure all mosfet

chips and inductor coils are covered.

Holes to be punched through!

M2.5 PVC washers

M3 PVC washers

M3 thumb nut

Dieses Handbuch passt für folgende Modelle

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Bedienungsanleitung

ekwb

ekwb 3831109816202 Leitfaden

ekwb

ekwb EK-FC980 GTX Ti Strix Handbuch

ekwb

ekwb EK-FC R9-390X TF5 Series Handbuch

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 D-RGB Bedienungsanleitung

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Bedienungsanleitung

ekwb

ekwb EK Series Bedienungsanleitung

ekwb

ekwb R9-290X Series Leitfaden

ekwb

ekwb EK-Supremacy MX AMD Series Bedienungsanleitung

ekwb

ekwb EK-Reservoir Combo DCP 2.2 Handbuch

ekwb

ekwb EK-FC WX9100 PRO BACKPLATE Bedienungsanleitung

ekwb

ekwb EK-Quantum Reaction AIO RX 6800/6900 D-RGB P240 - AMD Radeon... Bedienungsanleitung

ekwb

ekwb ASUS Z9PE-D8 Bedienungsanleitung

ekwb

ekwb EK-Annihilator EX/EP Series Bedienungsanleitung

ekwb

ekwb EK-PRO GPU WB RTX 30 0 Series Bedienungsanleitung

ekwb

ekwb EK-FB MSI X299 GAMING PRO CARBON RGB... Bedienungsanleitung

ekwb

ekwb EK-FB ASUS P7P55 KIT Leitfaden

ekwb

ekwb EK-FC1080 GTX FTW2 Bedienungsanleitung

ekwb

ekwb EK-XTOP D5 Handbuch

ekwb

ekwb EK-FB ASUS PRIME X299 Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC WX9100 PRO BACKPLATE Bedienungsanleitung

ekwb

ekwb EK-FB ASUS M5E Leitfaden

ekwb

ekwb EK-FC Titan X Leitfaden

ekwb

ekwb EK-Quantum Vector RE RTX 3080 Active Backplate... Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

ekwb EK-FB ASRock X299 RGB Monoblock Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken