Ekwb EK-Quantum Velocity Ryzen Edition UNC Standoffs -... Bedienungsanleitung

USER GUIDE

EK-Quantum

Velocity Ryzen Edition UNC Standoffs - AM5

Please note the installation of the product is intended to be undertaken

by an adequately trained and experienced person. You are installing the

product at your own risk. If you are not properly trained or experienced or

feel unsure about the installation procedure, please refrain from installing

the product yourself and contact our tech support for assistance. We

disclaim our liability for any damages to the product as well as incidental,

consequential, or indirect damages incurred due to improper or

inappropriate installation.

Before you start using this product, please follow these basic guidelines:

Please carefully read the manual before beginning the

installation process.

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion-inhibiting coolants is always recommended

for liquid cooling systems, and mandatory for nickel-plated

water blocks.

Do not use pure distilled water! For best results, EK recommends

the use of EK-Cryo Fuel coolants.

Make sure to thoroughly bleed air out of your water block, or

you will not reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

PREPARING THE AM4 WATER BLOCK FOR UPGRADE 4

PREPARING THE AM5 MOTHERBOARD 5

INSTALLING THE WATER BLOCK 7

CONNECTING THE D-RGB LED STRIP 8

TESTING THE LOOP 8

WARRANTY 9

SUPPORT AND SERVICE 10

SOCIAL MEDIA 10

- 4 -

BOX CONTENTS

AM5 Mounting Standoff (4 pcs)

PREPARING THE AM4 WATER BLOCK FOR UPGRADE

Important! Before starting, make sure to have a clean, ﬂat

surface to work on. It is recommended to put foam or soft

material to lay a motherboard on.

STEP 1

If the EK-Quantum Velocity Ryzen AM4 water block is already

installed, unscrew four (4) Thumb Nuts to detach it (As shown in the

picture). Save the parts for later use.

STEP 1

THUMB NUT

COILED SPRING

- 5 -

STEP 2

Clean the CPU cold plate using a non-abrasive cloth or Q-tip.

STEP 2

CLOTH

COLDPLATE

STEP 1

Using a Philips-head screwdriver remove the four UNC 6-32 screws

securing the original plastic hold-down clamps around the socket as

shown in the illustration. Remove the hold-down clamps and store

them away.

PREPARING THE AM5 MOTHERBOARD

UNC 6-32 SCREW

HOLD-DOWN

CLAMPS

STEP 1

- 6 -

STEP 2

Cleaning the CPU: Wipe the IHS clean using a non-abrasive cloth or

Q-tip as shown in the illustration.

STEP 2

IHS

NON-ABRASIVE CLOTH

STEP 3

Applying thermal compound: Apply the enclosed thermal grease

(thermal compound) on the CPU heat spreader – IHS – as shown in

the image. The layer of the thermal compound must be thin and even

in thickness over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

STEP 3

Thermal Grease

For this step, you will need:

- 7 -

STEP 1

Install four (4) AM5 Mounting screws onto your motherboard. It is

mandatory to put a saved plastic washer underneath each of the

screws. Tighten the screws until you reach the end of the thread.

Using tools (such as pliers) is not recommended.

STEP 1

INSTALLING THE WATER BLOCK

STEP 2

Align the water block over the mounting screws on the motherboard.

Place a saved compression spring and thumb nut over each AM5

Mounting screw. Start fastening two thumb nuts at a time, preferably

in a cross pattern, and do not tighten them fully until all of them are

partially screwed in. Then - using your ﬁngers only - screw in all four

thumb nuts until you reach the end of the thread.

THUMB NUT

SPRING

AM5 MOUNTING SCREW

PVC WASHER

- 8 -

STEP 1

Plug the 3-pin connector from the water block’s D-RGB LED light to

the DRGB HEADER on the motherboard. The LED will work if the pin

layout on the header is as follows: +5V, Digital, empty, Ground.

Please ensure that the arrow indicated on the connector is

plugged into the +5V line as indicated on your motherboard.

If you put the LED Diode to the 12V RGB HEADER you

can damage the LEDs. Failure to do so will damage your

motherboard or LED strip.

D-RGB HEADER

RGB HEADER

STEP 1

CONNECTING THE D-RGB LED STRIP

To make sure the installation of EK components was successful, we

recommend you perform a leak test for 24 hours. When your loop

is complete and ﬁlled with coolant, connect the pump to a PSU

outside of your system. Do not connect power to any of the other

components. Turn on the PSU and let the pump run continuously.

It is normal for the coolant level to drop during this process as air

collects in the distribution plate. Inspect all parts of the loop, and

in the eventuality that coolant leaks, ﬁx the issue and repeat the

testing process. Ensure that all hardware is dry before the system is

powered on in order to prevent any damage.

TESTING THE LOOP

- 9 -

Our products are warranted against defects of materials and

quality for a period of 24 months, starting with the date of

delivery to the end-user. During this period, products will be

repaired or have parts replaced at our discretion, provided

that 1) the product is returned to the agent from whom it was

purchased; 2) the product has been purchased by the end-user

and has not been used for commercial purposes; 3) the product

has not been misused, handled carelessly, or used in a manner

other than the way described in the instructions manual. This

warranty does not confer rights other than those expressly set

out above and does not cover any claims for consequential loss

or damage. This warranty is offered as an extra benefit and does

not affect your statutory rights as a consumer. This warranty

is voided if the product comes in contact with aggressive UV

additives or other improper liquids. EK water blocks are sealed

with a warranty-voiding circular label, proving the water block

has withstood a pressure leak test. Removing the label will void

the leak-free guarantee, but not the guarantee on the product

itself. Any other RMA issues can be reported to EK Customer

Support at www.ekwb.com/support for further analysis.

WARRANTY

In case you need assistance or wish to order spare parts or a new

mounting mechanism, please contact:

https://www.ekwb.com/customer-support/

EKWB d.o.o.

Pod lipami 18

1218 Komenda

Slovenia - EU

SUPPORT AND SERVICE

EKWaterBlocks

@EKWaterBlocks

ekwaterblocks

EKWBofﬁcial

SOCIAL MEDIA

Inhaltsverzeichnis

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-Quantum Vector RTX 3080/3090 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FC 5970 Handbuch

ekwb

ekwb EK-FC 6970 Handbuch

ekwb

ekwb EK-Classic GPU Water Block RTX 3080/3090... Bedienungsanleitung

ekwb

ekwb EK-Quantum Kinetic TBE DDC PWM Series Bedienungsanleitung

ekwb

ekwb EK-FC 780 GTX DCII Series Handbuch

ekwb

ekwb EK-FB KIT ASUS R4BE Leitfaden

ekwb

ekwb EK-FC 4890 VAPOR X Leitfaden

ekwb

ekwb EK-7970 Leitfaden

ekwb

ekwb EK-SB ASUS M6G Leitfaden

ekwb

ekwb EK-Quantum Volume FLT Series Bedienungsanleitung

ekwb

ekwb EK-Annihilator Pro ILM Series Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector FE RTX 3080 Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX FTW Bedienungsanleitung

ekwb

ekwb EK-Nucleus AIO CR360 Lux D-RGB Bedienungsanleitung

ekwb

ekwb EK-PRO GPU WB H100 Rack - Nickel + Inox Bedienungsanleitung

ekwb

ekwb EK-Reservoir Combo DCP 2.2 Handbuch

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Bedienungsanleitung

ekwb

ekwb EK-FC7950 Handbuch

ekwb

ekwb EK-FB ASUS M5E Leitfaden

ekwb

ekwb EK-FC5x0 GW GTX water block Handbuch

ekwb

ekwb EK-Supreme HF Leitfaden

ekwb

ekwb EK-FC980 GTX Ti Classy KPE Series Handbuch

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

ekwb EK-Quantum Velocity Ryzen Edition UNC Standoffs -... Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken