Ekwb EK-PRO GPU WB H100 Rack - Nickel + Inox Bedienungsanleitung

USER GUIDE

GPU WATER BLOCK

EK-PRO

GPU WB H100 Rack - Nickel + Inox

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with the

rubber O-ring gaskets.

The use of quality market-proven corrosion-inhibiting

coolants is always strongly recommended for any liquid

cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

Make sure to bleed air out of your water block thoroughly in

order to reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6

PREPARING YOUR GRAPHICS CARD 7

REMOVING THE STOCK COOLER 7

CLEANING THE PCB 7

CUTTING AND PLACING THERMAL PADS 8

APPLYING THERMAL COMPOUND 9

INSTALLING THE WATER BLOCK 9

PLACING THE BLOCK ON THE GRAPHICS CARD 9

CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES 11

ATTACHING THE WATER BLOCK 11

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 12

TESTING THE LOOP 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

- 4 -

PLUG G1/4 CSQ-Bridge (2x)

3830046999153

Allen Key 2mm (1x) 8901

BOX CONTENTS

EK-Loop Multi Allen Key (1x)

3830046996213

Screw M2.5x10 ax1 - Black (3x)

104344

Thermal PAD F 1.0mm - (120x16mm)

3830046996732

PASTE Thermal Grizzly Hydronaut

(1g) (1x) 3830046998477

EK-Pro GPU WB H100 Rack - Nickel + Inox (1x) 3831109908792

Washer POLYAMID M2.5 0.7mm

with self-adhesive tape (6x) 8627

120 mm

16 mm

Washer

POLYAMID M2.5 0.5mm

(10x) 8623

Screw size guide (1x) 103012

Screw M2.5x7 ax1 (8x)

9049H100 Rack Backplate (1x) 107035

- 5 -

WATER BLOCK DIMENSIONS

255.7 mm

244.3 mm

126.9 mm

96.9 mm

242.4 mm

139.3 mm

20.1 mm

17.8 mm

21.7 mm

29 mm

46.9 mm 51 mm

21.7 mm

17.8 mm

- 6 -

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

Position EAN

Description

Quantity

1107032 099 - Baker - H100 Rack Coldplate (Ni) 1

2107041 099 - Kovina - H100 Rack Insert 2

3107036 099 - Kovina - H100 Rack Pro Top 1

4107037 099 - Alu - H100 Rack Power Adapter 1

5107064 099 - OR - H100 Rack 1

6103767 top acetal - FC terminal Direct (2x G1-4) 1

7100006 Vijak M4x27 DIN7984 3

85155 OR 15x1 EPDM50 (FC Terminal) 2

9103987 Distancer M3.5-M2.5 x 3 Medenina 8

10 103089 vijak M3x5 ISO 14581 TX - INOX 24

11 107088 OR 6x2 EPDM 1

12 102490 Medenina - Pro GPU Bracket standoff

M4-6/32 - Ni 1

13 8483 ISO 7380 - UNC6-32 x 5 1

*107035 98 - Alu - H100 Rack Backplate (Bl. Elox) 1

* included in the Box Contents

- 7 -

PREPARING YOUR GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Place your graphics card on the ﬂat surface and carefully remove

the stock cooler. Do not forget to unplug all the LED and fan

connectors. Pay attention to the following steps in order to install

the EK-Pro GPU WB H100 Rack - Nickel + Inox water block onto

the graphics card.

STEP 2

CLEANING THE PCB

Wipe off the remains of the original thermal compound using a

nonabrasive cloth or Q-tip, as shown in the sample image, until the

components and circuit board are completely clean. EK recommends

the use of denatured alcohol for removing TIM leftovers. After that,

remove all remaining stock thermal pads from the PCB.v

STEP 2

- 8 -

CUTTING AND PLACING THERMAL PADS

STEP 1

Your GPU water block comes with un-cuted thermal pads to cover

all the VRM components, such as COILs, MOSFETs, and drivers.

Please use 1.0 mm thick thermal pads which should be placed on

the water block, as illustrated below. EK made sure to provide you

with more than an adequate quantity of thermal pads to complete

this Step.

You must remove the protective foil from both sides of the

thermal pad before installation.

Thermal Pad F 1.0 mm

STEP 2

Please use 1.0 mm thick thermal pads which should be placed on

the backplate, as illustrated below. EK made sure to provide you

with more than an adequate quantity of thermal pads to complete

this Step.

You must remove the protective foil from both sides of the

thermal pad before installation.

Thermal Pad F 1.0 mm

STEP 1

STEP 2

- 9 -

INSTALLING THE WATER BLOCK

STEP 1

PLACING THE BLOCK ON THE GRAPHICS CARD

This procedure is the same for all full-cover water blocks. Carefully

position the water block with preinstalled standoffs on the graphics

card. During this process, make sure you have aligned mounting

holes of the PCB with holes of the water block.

Pay attention not to use too much force when pressing

the block down to the PCB since chip dies are prone

to cracking.

STEP 1

Thermal Grease

Apply the enclosed EK-TIM Ectotherm thermal grease (thermal

compound) on the GPU heat spreader – IHS – as shown in the

image. The layer of the thermal compound must be thin and even

over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

APPLYING THERMAL COMPOUND

For this Step, you will need:

- 10 -

STEP 4

Secure power cable with mounting it into included inox power

adapter.

STEP 4b

Insert 8-pin power connector in to the inox adapter. Pads on the

power adapter must be alligned with openings in inox power adapter.

Pay attention to the orietation of the latch on connector.

STEP 3

Use stock cross backplate from the original card and mount it with

original stock M3 screws.

Inhaltsverzeichnis

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-Reservoir Combo DCP 2.2 Handbuch

ekwb

ekwb EK-FC285 GTX Classified Handbuch

ekwb

ekwb EK-FC1080 GTX FTW Bedienungsanleitung

ekwb

ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB Bedienungsanleitung

ekwb

ekwb EK-FC Fury X Handbuch

ekwb

ekwb EK-FC980 GTX Ti Strix Series Handbuch

ekwb

ekwb EK-FB KIT GA P67A UD7 Handbuch

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Bedienungsanleitung

ekwb

ekwb EK H30 SUPREME Bedienungsanleitung

ekwb

ekwb EK-FC R9-295X2 Leitfaden

ekwb

ekwb EK-FC980 GTX Leitfaden

ekwb

ekwb EK-FC7970 DCII Leitfaden

ekwb

ekwb EK-FB KIT GA-X99 SOC Champion Series Handbuch

ekwb

ekwb EK-FB GA AMD KIT Handbuch

ekwb

ekwb EK-FC Titan X Leitfaden

ekwb

ekwb EK-FC780 GTX Classy Rev.2.0 Backplate Leitfaden

ekwb

ekwb EK-FC7870 GTX Handbuch

ekwb

ekwb EK-BAY DCP 2.2 Handbuch

ekwb

ekwb D-RGB Bedienungsanleitung

ekwb

ekwb EK-Supremacy MX AMD Series Bedienungsanleitung

ekwb

ekwb EK-FB KIT EVGA SR-X Installationsanleitung

ekwb

ekwb EK-FC1080 GTX Ti Strix Bedienungsanleitung

ekwb

ekwb EK-FC R9-390X TF5 Leitfaden

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

ekwb EK-PRO GPU WB H100 Rack - Nickel + Inox Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken