Ekwb MSI MPG Z490 Carbon EK X Bedienungsanleitung

USER GUIDE

MONOBLOCK

MSI MPG Z490 Carbon

EK X Monoblock

This product is intended for installation by expert users only.

Please consult with a qualified technician for installation. Improper

installation may result in damage to the equipment. EK Water

Blocks assumes no liability whatsoever, expressed or implied,

for the use of these products, nor their installation. The following

instructions are subject to change without notice. Please visit our

website at www.ekwb.com for updates. Prior to the installation

of this product, please read important notice, disclosure, and

warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process!

Remove your motherboard from the chassis for the safest

mounting process and to prevent any possible damages.

EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with the

rubber o-ring gaskets.

The use of quality market-proven corrosion-inhibiting

coolants is always strongly recommended for any liquid

cooling system.

- 3 -

TABLE OF CONTENT

BOX CONTENTS 4

PREPARING YOUR MOTHERBOARD 5

REMOVING THE STOCK COOLER 5

APPLYING THERMAL COMPOUND 6

CUTTING AND PLACING THERMAL PADS 6

PLACING THE BLOCK ON THE MOTHERBOARD 7

ATTACHING BLOCK ON THE MOTHERBOARD 7

CONNECTING THE DRGB LED STRIP 9

TESTING THE LOOP 9

SUPPORT AND SERVICE 10

SOCIAL MEDIA 10

- 4 -

BOX CONTENTS

MSI MPG Z490 Carbon EK X Monoblock

M4 x 8 7984DIN (5 pcs) M2.5 x 5 AX1 Screws (5 pcs)

M4 PVC Washers (5 pcs)

2.5. mm Allen Key (1 pc)

M2.5 PVC Washers (5 pcs)

Thermal Grease (1 pc) M2.5 Adhesive PVC Washers (5pcs)

MOUNTING MECHANISM - Bag content is universal; you may not need every screw

- 5 -

PREPARING YOUR MOTHERBOARD

REMOVING THE STOCK COOLER

STEP 1

There are two (2) screws on the back of

the motherboard that need to be removed to allow for the removal

of I/O plastic cover.

STEP 2

After removing the I/O cover, you need to remove four(4) MOSFET

screws and take off the VRM MOSFET cooler.

You can attach the I/O cover back on after you have mounted

the Monoblock.

STEP 1&2

Mosfet screws I/O Cover

Screws

- 6 -

CUTTING AND PLACING THERMAL PADS

Your block comes with two pieces of thermal pads that need to

be trimmed to ﬁt the voltage regulation area (MOSFET) on the

motherboard’s circuit board.

1. Thermal PAD F 1.0mm - (120x16mm)

Thermal Pad F 1.0mm - (120x16mm)

120

Thermal Pad

F 1.0mm

APPLYING THERMAL COMPOUND

Apply the enclosed EK-TIM Ectotherm thermal grease (thermal

compound) on the CPU heat spreader – IHS – as shown in the

image. The layer of the thermal compound must be thin and even in

thickness over the entire surface of the IHS. The excessive or uneven

application may lead to poor performance!

- 7 -

PLACING THE BLOCK ON THE MOTHERBOARD

Place your MSI MPG Z490 Carbon EK X monoblock on the

motherboard, as shown in the scheme. Make sure that mounting

holes are aligned.

Before placing the monoblock on to the motherboard, make sure

that protective sticker on the coldplate is removed!

ATTACHING BLOCK ON THE MOTHERBOARD

STEP 1

Before you fasten the screws, please make sure the mounting holes

on the motherboard’s circuit board are aligned with the water block.

While tightening the screws, do not use excessive force!

For the CPU:

Use four (4) M4 X 8 DIN7984 screws and M4 PVC washers. Tighten

the screws evenly using the enclosed 2.5mm Allen Key.

STEP 1

M4 x 8 DIN7984

M4 PVC Washer

FOR CPU

- 8 -

For Mosfet:

Use four (4) M2.5 x 5 AX1 screws with M2.5 PVC washers. Tighten

the screws evenly.

M2.5 x 5 AX1

STEP 1

STEP 2

For the MSI MPG Z490 Carbon EK X monoblock to operate properly,

the G1/4 port nearest to the right edge of the water block MUST BE

USED AS THE INLET PORT.

STEP 2

IMPORTANT:

Use this opening

as the Inlet Port!

FOR MOSFET

M2.5 PVC Washer

- 9 -

CONNECTING THE D-RGB LED STRIP

Plug the 3-pin connector from the Monoblock’s D-RGB LED light to

the D-RGB Header on the motherboard. The LEDs will work if the pin

layout on the header is as follows: +5V, Data, Empty, Ground.

D-RGB Header

RGB Header

To make sure the installation of EK components was successful, we

recommend you perform a 24-hour leak test.

When your loop is complete and ﬁlled with coolant, connect the

pump to a PSU outside of your system. Do not connect power to

any of the other components. Turn on the PSU and let the pump

run continuously.

Inspect all parts of the loop, and in case the coolant leaks, ﬁx the

issue and repeat the testing process. Ensure that all hardware is dry

before the system is powered on, to prevent any damage.

TESTING THE LOOP

For assistance please contact:

http://support.ekwb.com/

EKWB d.o.o.

Pod lipami 18

1218 Komenda

Slovenia - EU

EKWaterBlocks

@EKWaterBlocks

ekwaterblocks

EKWBofﬁcial

SUPPORT AND SERVICE

SOCIAL MEDIA

Inhaltsverzeichnis

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-FC R9-295X2 Handbuch

ekwb

ekwb EK-FB ASR Z77 Extreme11 Leitfaden

ekwb

ekwb EK-FC780 GTX Ti Series Bedienungsanleitung

ekwb

ekwb EK-FCW8100 Leitfaden

ekwb

ekwb EK-UNI Handbuch

ekwb

ekwb Ultra Monoblock EK-FB GA X99 Bedienungsanleitung

ekwb

ekwb EK-Pro Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Strix X299-E RGB Monoblock Bedienungsanleitung

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Bedienungsanleitung

ekwb

ekwb EK-FC580 DCII Handbuch

ekwb

ekwb Classic D-RGB S240 Bedienungsanleitung

ekwb

ekwb Velocity - Intel Bedienungsanleitung

ekwb

ekwb EK-PRO GPU WB RTX 6000 ADA Nickel Inox Bedienungsanleitung

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Leitfaden

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 D-RGB Bedienungsanleitung

ekwb

ekwb EK-FC1080 G1 GTX Backplate Leitfaden

ekwb

ekwb EK-Vector Strix RTX 2070 Backplate Leitfaden

ekwb

ekwb EK-Quantum Vector XC3 RTX 3080 D-RGB Bedienungsanleitung

ekwb

ekwb Supremacy EVO Bedienungsanleitung

ekwb

ekwb EK-UNI RAD Handbuch

ekwb

ekwb 3831109816202 Leitfaden

ekwb

ekwb EK-FB GA AMD KIT Handbuch

ekwb

ekwb EK-FB KIT EVGA SR-X Installationsanleitung

ekwb

ekwb EK Series Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

ekwb MSI MPG Z490 Carbon EK X Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken