ekwb EK-PRO GPU WB RTX 6000 ADA Nickel Inox Bedienungsanleitung
USER GUIDE
GPU WATER BLOCK
EK-PRO
GPU WB RTX 6000 ADA – Nickel Inox
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.
- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
WATER BLOCK DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6
PREPARING YOUR GRAPHICS CARD 7
REMOVING THE STOCK COOLER 7
CLEANING THE PCB 7
CUTTING AND PLACING THERMAL PADS 8
APPLYING THERMAL COMPOUND 8
INSTALLING THE WATER BLOCK 9
PLACING THE BLOCK ON THE GRAPHICS CARD 9
ATTACHING THE BACKPLATE 12
CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES 12
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 13
TESTING THE LOOP 13
SUPPORT AND SERVICE 14
SOCIAL MEDIA 14
- 4 -
PLUG G1/4 CSQ-Bridge (2x)
3830046999153
EK-Pro GPU WB RTX 6000 ADA Rack – Full Al 3831109906682
Allen Key 2mm (1x) 8901
BOX CONTENTS
Screw M2.5x4 ax1 (4x)
9047
EK-Loop Multi Allen Key (1x)
3830046996213
Screw size guide (1x) 103012
EK-TIM Ectotherm (1g) (1x)
3830046998446
Washer POLYAMID M2.5 0.7mm
with self-adhesive tape (6x) 8627
Washer
POLYAMID M2.5 0.5mm
(20x) 8623
Screw M2.5x6 ax1 (4x)
9058
Screw M2.5 x 7 ax1 (8x)
9049
Screw M2.5x8 3825040ax1 -
Nickel (4x) 8104N
- 5 -
WATER BLOCK DIMENSIONS
262 mm
250.6 mm
248.4 mm
155.5 mm
96.9 mm
125.5 mm
19.3 mm
23.9 mm
21.2 mm
130.8 mm32.5 mm
- 6 -
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS
Position EAN Description Quantity
1106618 094 - baker - RTX 6000 ADA Coldplate 1
2106439 Top Acetal - Pro Terminal GPU 45 deg
G1- 4 v2 1
39013 Vijak M4 x 8 DIN7984 2
48323 Vijak M4 x 28 DIN7984 1
55155 OR 15 x 1 EPDM50 (FC Terminal) 2
6106133 TOP Plexi - Vector2Insert R5 1
7106623 094 - kovina - RTX 6000 ADA top 1
8094 - kovina - RTX 6000 ADA Power
Adapter 1
98625 Podložka POLYAMID M3 0.5 mm
samolepljiva 2
10 106640 Distancer M3 - M2.5 x 11.5 Pro
Medenina (female) 1
11 106624 094 - alu - RTX 6000 ADA Backplate 1
12 103089 vijak M3 x 5 ISO 14581 TX INOX 13
13 8104A Vijak M2.5 x 8 3825040ax1 3
14 9058 Vijak M2.5 x 6 3825040ax1 2
15 9049 Vijak M2.5 x 7 3825040ax1 4
16 103987 Distancer M3.5-M2.5 x 3 Medenina 4
17 103988 Distancer M4-M2.5 x 3 mm Vector2
(Nickel) 4
18 106638 094 - OR - RTX 6000 ADA 1
19 8211N Vijak M3 x 5 DIN7991 - Nickel 2
12
13
16
11
17
18
2
1
7
4
3
19
14
9
8
10
12
5
8
- 7 -
PREPARING YOUR GRAPHICS CARD
STEP 1
REMOVING THE STOCK COOLER
Place your graphics card on the flat surface and carefully remove the
stock cooler. Do not forget to unplug all the LED and fan connectors.
Pay attention to the following steps in order to install the EK-Pro
GPU RTX 6000 ADA water block onto the graphics card.
STEP 2
CLEANING THE PCB
Wipe off the remains of the original thermal compound using a
nonabrasive cloth or Q-tip, as shown in the sample image, until the
components and circuit board are completely clean. EK recommends
the use of denatured alcohol for removing TIM leftovers. After that,
remove all remaining stock thermal pads from the PCB.
STEP 2
- 8 -
CUTTING AND PLACING THERMAL PADS
Your GPU water block comes with un-cuted thermal pads to cover
all the VRM components, such as COILs, MOSFETs , and drivers.
Please use 1.0 mm thick thermal pads which should be placed on
the PCB, as illustrated below. EK made sure to provide you with more
than an adequate quantity of thermal pads to complete this Step.
You must remove the protective foil from both sides of the
thermal pad before installation.
Thermal Grease
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the GPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
APPLYING THERMAL COMPOUND
For this Step, you will need:
Thermal Pad - 120 x 16 x 1.0 mm
F1
- 9 -
INSTALLING THE WATER BLOCK
STEP 1
PLACING THE BLOCK ON THE GRAPHICS CARD
This procedure is the same for all full-cover water blocks. Carefully
position the water block with preinstalled standoffs on the graphics
card. During this process, make sure you have aligned mounting
holes of the PCB with holes of the water block.
Pay attention not to use too much force when pressing
the block down to the PCB since chip dies are prone
to cracking.
STEP 1
STEP 2
M2.5 x 4 AX1 SCREW
STEP 2
To attach graphich card to waterblock use stock cross backplate.
Mount it with polyamind M2.5 pads and stock M2.5 x 4 screws.
- 10 -
STEP 3bSTEP 3a
STEP 3
Secure power cable with mounting it into included inox power
adapter.
STEP 3a
Stick the two included plastics pads (M3) on to inox power addapter
as shown on picture.
STEP 3b
Insert 8-pin power connector in to the inox adapter. Pads on the
power adapter must be alligned with openings in inox power adapter.
Pay attention to the orietation of the latch on connector.
For this Step, you will need:
M3 x 5 SCREW
STEP 3c
STEP 3c
Fasten a inox power adaptor to the water block with two (2) M3 x 5
screws. When power cables is installed there is needed a litlle bend
and twist of power cables in order to atteched power adaptor to
water block.
Allen Key 2mm
(1x) 8901
Screw M3 x 5 DIN 7991
(2x) 8211
Inhaltsverzeichnis
Andere ekwb Computerhardware Handbücher
ekwb
ekwb EK-FC970 GTX TF5 Handbuch
ekwb
ekwb EK-XRES 140 Revo D5 Series Leitfaden
ekwb
ekwb EK-FC1080 GTX FTW Bedienungsanleitung
ekwb
ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung
ekwb
ekwb EK-Supremacy MX AMD Series Bedienungsanleitung
ekwb
ekwb EK-7970 Leitfaden
ekwb
ekwb EK-FC Titan X Original CSQ Handbuch
ekwb
ekwb EK-FB ASUS PRIME X299 Monoblock Bedienungsanleitung
ekwb
ekwb EK-FC R9 Fury X Leitfaden
ekwb
ekwb EK-FB KIT GA P67A UD7 Handbuch
ekwb
ekwb EK-FCQK5000 Handbuch
ekwb
ekwb EK-FC R9-280X DCII Bedienungsanleitung
ekwb
ekwb EK-Quantum Kinetic TBE 120 VTX PWM Bedienungsanleitung
ekwb
ekwb EK-Quantum RX 6800 Bedienungsanleitung
ekwb
ekwb EK-D5 Dual TOP CSQ Handbuch
ekwb
ekwb EK-FC780 GTX Jetstream Handbuch
ekwb
ekwb EK-Quantum Vector RE RTX 3080 Active Backplate... Bedienungsanleitung
ekwb
ekwb Ultra Monoblock EK-FB GA X99 Bedienungsanleitung
ekwb
ekwb EK-FB MSI X299 GAMING PRO CARBON Monoblock Bedienungsanleitung
ekwb
ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
