Elabs AV501HDXi Bedienungsanleitung
LAUNAMNOITCURTSNI
Component Video/Audio
HDTV Distribution Amplifier
Includes Input Ground Isolation Circuitry
Helps Eliminate Video Hum Bar Problems
AV501HDXi
True One-to-One Signal Ratio
Duplicates a Video/Audio Source to multiple
outputs without any signal loss.
Designed for large display arrays.
Heavy duty metal housing. Commercial duty rated.
CE labs can support many areas of your audio and video
distribution needs.
We manufacture:
• Digital Signage software and Media Players
• HD Matrix Switchers
• RF amplifiers
• HDMI and Component HD distribution amplifiers
• CAT 5 Signal Extenders
• VGA Extenders and Splitters
• and cables of all types.
See our full product line at www.celabs.net
WARRANTY
Cable Electronics, Inc. warrants this product to be free from defects in
material and workmanship, under normal use and service, for a period of
one year from the purchase by the original purchaser. If this product is
defective or malfunctions, Cable Electronics will replace or repair this unit
(at their option) within a reasonable time. No expressed or implied warranty
is made for any defects caused by immersion or exposure to liquids, abuse,
neglect, improper operation of unit, excess wear and tear and defects
resulting from unauthorized disassembly and or modification.
Document: AV501HDXi_manual.pdf
930_5054_01_Rev.A
3209 Wood Drive
Garland, TX 75041
Phone: (469) 429-9200
Toll free: (800) 767-6189
Fax: (469) 429-9205
www.celabs.net
This unit is very effective in breaking AC ground loops that cause moving
video hum bars. If a system using non-isolated distribution amplifiers is
exhibiting hum bars, place the AV501HDXi between the video source and
the first distribution amplifier. This should eliminate or greatly reduce visible
hum bars. Larger display systems may contain more than one AC ground
loop, and require more than one isolated input amplifier to totally eliminate
the issue.
SPECIFICATIONS
VIDEO
Nominal Input level: 1 Volt peak to peak
Gain: 1 Volt into 75 ohms
2 Volts Unterminated
Input Impedance: 75 ohms
Output Impedance: 75 ohms
Isolation port to port: 32 dB
Isolation output to input: 60 dB
Return loss: >18 dB
Video bandwidth: 150 MHz
AUDIO
Analog:
Nominal Input level: 1 Volt peak to peak
Gain: Unity (one to one)
Input impedance: 22k ohm
Output impedance: 1k ohm
THD: <0.05%
Frequency Response: 20Hz to 100kHz
Channel Separation: >75dB
Port to Port Isolation: 60dB
Out to Input Isolation: 60dB
Signal to Noise: >100dB @ 2 Volts out
Digital:
Supports Standard SPDIF digital audio. Unity gain when terminated
into 75 ohms (2X gain, high impedance.) Greater than 50 MHz of
bandwidth to ensure minimal degradation.
POWER
Requirement: External 9 ro 10 Volt AC @ 1000mA with a (2.1mm
center diameter) Coaxial Connector.
Power supply is included.
IN OUT IN OUT
Source
VIDEO
AUDIO
AV501HDXi
The AV501HDXi incorporates isolation circuitry on the input connectors that
helps to eliminate AC hum bars associated with ground loops. The ground
connection on the inputs is isolated by a high impedance that effectively
breaks the AC ground loops.
The AV501HDXi has one set of inputs and five sets of outputs (Output #5 is
designated as the loop output, but may be used to drive a monitor directly).
The unit allows any Audio/Video source, with Y, Cb, Cr, or Y, Pb, Pr Outputs
(component), to distribute Audio and Video to five different locations without
any signal loss. The amplifier also supports composite video and digital audio.
Note: the loop output may be used to daisy chain several units together as is
typically done in store displays.
INSTALLATION/OPERATION INSTRUCTIONS
Unpack the amplifier and power supply from the box. Place the amplifier in
a dry location, usually behind the shelf where the monitors are located.
The unit has integrated mounting brackets that are pre-drilled in case the
user wishes to screw the unit to the shelf (screws supplied by user).
Connect the source device outputs to the appropriate input jacks on the
AV501HDXi.
Connect cabling from the AV501HDXi outputs to the desired display or
recording device.
The loop output may be used as normal or connect to the next distribution
amplifier to create more outputs.
Insert the power supply connector into the power jack of the AV501HDXi.
Plug the wall transformer into a 120Vac outlet. The power LED should be on
and the unit is ready to use.
Andere Elabs Verstärker Handbücher
