ELAC DCB41 Bedienungsanleitung

DEBUT ConneX DCB41DCB41

Batteries

Rubber Foot

Contents - Contenu - Inhalt

Power Cord Speaker Cable

Remote Control

HDMI Cable

ELAC DEBUT ConneX DCB41 | www.elac.com | Page 2

Connections

4. Connect AC mains

1. Connect speakers together with supplied wire

2. Connect source - TV, Computer, Phono

3. Connect Source - Bluetooth

ELAC DEBUT ConneX DCB41 | www.elac.com | Page 3

Model : DCB41

UPDATE ONLY

HDMI (ARC)

1938 N. Batavia St.

Suite K

Orange, CA, 92865

Fraunhofestrabe 16

24118 Kiel, Deutchland

SERIAL NUMBER

USB OPT SUB OUT

PHONO

ON/OFF

CAN ICES-0003(B)/NMB-003(B)

FCC ID: XXX-XXXXX

IC: XXXXX-XXXXX

Desinged by Elac

Made in China

SPEAKER OUT

120-240V~50/60Hz AC

80W

L/R

GND

OUT

SPEAKER

ELAC DEBUT ConneX DCB41 | www.elac.com | Page 4

1. AC Mains Inlet

2. HDMI (ARC) Input

3. Volume/Power/Source

4. L/R switch

7. USB Input

8. Optical Input

9. SubWooofer Output

10. Phono/Line Switch

Controls and Inputs/Output

5. USB for Update

6. Ground Screw Terminal

11. Line/Phono Input

12. Speaker Output

The Volume knob can be used to adjust volume, change input and power on/o.

Rotate: Rotating the knob will increase or decrease volume.

Push:

Press to turn on unit.

Press and hold in BT input to initiate pairing

Press when on to change input. Front LED colours are:

[BT - Blue] [HDMI - Green] [USB - White] [Optical - Red] [Phono - Pink]

4 5

7 8 9 10 11

Model : DCB41

UPDATE ONLY

HDMI (ARC)

1938 N. Batavia St.

Suite K

Orange, CA, 92865

Fraunhofestrabe 16

24118 Kiel, Deutchland

SERIAL NUMBER

USB OPT SUB OUT

PHONO

ON/OFF

CAN ICES-0003(B)/NMB-003(B)

FCC ID: XXX-XXXXX

IC: XXXXX-XXXXX

Desinged by Elac

Made in China

SPEAKER OUT

120-240V~50/60Hz AC

80W

L/R

GND

OUT

SPEAKER

Set to ON if plugging into a turntable

Audio Out

Ground

ON/OFF

Optional

Note: Some turntables have built in pre-ampliﬁers that can be disabled. Ensure the turn-

table pre-ampliﬁer is set to O and DCB41 is set to ON.

If you choose to use the turntable’s Phono pre-ampliﬁer, then ensure its switch is set to

ON postion and DCB41 is set to OFF.

The Ground connection is optional. It is recommended to be used as it can lower residu-

al noise.

CONNECTIONS - TURNTABLE

ELAC DEBUT ConneX DCB41 | www.elac.com | Page 5

Model : DCB41

UPDATE ONLY

HDMI (ARC)

1938 N. Batavia St.

Suite K

Orange, CA, 92865

Fraunhofestrabe 16

24118 Kiel, Deutchland

SERIAL NUMBER

USB OPT SUB OUT

PHONO

ON/OFF

CAN ICES-0003(B)/NMB-003(B)

FCC ID: XXX-XXXXX

IC: XXXXX-XXXXX

Desinged by Elac

Made in China

SPEAKER OUT

120-240V~50/60Hz AC

80W

L/R

GND

OUT

SPEAKER

Model : DCB41

UPDATE ONLY

HDMI (ARC)

1938 N. Batavia St.

Suite K

Orange, CA, 92865

Fraunhofestrabe 16

24118 Kiel, Deutchland

SERIAL NUMBER

USB OPT SUB OUT

PHONO

ON/OFF

CAN ICES-0003(B)/NMB-003(B)

FCC ID: XXX-XXXXX

IC: XXXXX-XXXXX

Desinged by Elac

Made in China

SPEAKER OUT

120-240V~50/60Hz AC

80W

L/R

GND

OUT

SPEAKER

HDMI-ARC

Optical

Note: HDMI supports eARC and ARC inputs from most

televisions.

Your television remote control can also control, power,

mute and volume of your Debut ConneX.

CONNECTIONS - SUBWOOFER

CONNECTIONS - TELEVISION

ELAC DEBUT ConneX DCB41 | www.elac.com | Page 6

Can be connected via

HDMI or Optical Cable

Model : DCB41

UPDATE ONLY

HDMI (ARC)

1938 N. Batavia St.

Suite K

Orange, CA, 92865

Fraunhofestrabe 16

24118 Kiel, Deutchland

SERIAL NUMBER

USB OPT SUB OUT

PHONO

ON/OFF

CAN ICES-0003(B)/NMB-003(B)

FCC ID: XXX-XXXXX

IC: XXXXX-XXXXX

Desinged by Elac

Made in China

SPEAKER OUT

120-240V~50/60Hz AC

80W

L/R

GND

OUT

SPEAKER

CONNECTIONS - COMPUTER

Connect to your USB devices USB Type B cable

(printer cable)

CONNECTIONS - BLUETOOTH

When initial power up - BT LED will ﬂash if nothing is paired to it.

When LED is ﬂashing, “ELAC DCB41” is vissible on your device.

Pairing can also be initited as follows:

Press and hold BT source on remote until LED ﬂashes.

Press and hold rear volume button when in BT input until LED ﬂashes

ELAC DEBUT ConneX DCB41 | www.elac.com | Page 7

Model : DCB41

UPDATE ONLY

HDMI (ARC)

1938 N. Batavia St.

Suite K

Orange, CA, 92865

Fraunhofestrabe 16

24118 Kiel, Deutchland

SERIAL NUMBER

USB OPT SUB OUT

PHONO

ON/OFF

CAN ICES-0003(B)/NMB-003(B)

FCC ID: XXX-XXXXX

IC: XXXXX-XXXXX

Desinged by Elac

Made in China

SPEAKER OUT

120-240V~50/60Hz AC

80W

L/R

GND

OUT

SPEAKER

ELAC DEBUT ConneX DCB41 | www.elac.com | Page 8

REMOTE CONTROL

Hex CodesRemote Control

BT Source

Next(BT)

Volume Up

Phono Source

Volume Up

HDMI Source

Power ON/OFF

Optical Source

Volume Down

Previous (BT)

Adjus LED Intensity

Mute

USB Source

The L/R switch is in reference to

speaker output terminals.

If L/R switch is set to “L” then the

speaker output will be the LEFT

speaker.

IF L/R switch is set to “R” then the

speaker output will be the RIGHT.

SETTING LEFT or RIGHT SPEAKER

Model : DCB41

UPDATE ONLY

HDMI (ARC)

1938 N. Batavia St.

Suite K

Orange, CA, 92865

Fraunhofestrabe 16

24118 Kiel, Deutchland

SERIAL NUMBER

USB OPT SUB OUT

PHONO

ON/OFF

CAN ICES-0003(B)/NMB-003(B)

FCC ID: XXX-XXXXX

IC: XXXXX-XXXXX

Desinged by Elac

Made in China

SPEAKER OUT

120-240V~50/60Hz AC

80W

L/R

GND

OUT

SPEAKER

Model : DCB41

UPDATE ONLY

HDMI (ARC)

1938 N. Batavia St.

Suite K

Orange, CA, 92865

Fraunhofestrabe 16

24118 Kiel, Deutchland

SERIAL NUMBER

USB OPT SUB OUT

PHONO

ON/OFF

CAN ICES-0003(B)/NMB-003(B)

FCC ID: XXX-XXXXX

IC: XXXXX-XXXXX

Desinged by Elac

Made in China

SPEAKER OUT

120-240V~50/60Hz AC

80W

L/R

GND

OUT

SPEAKER

1. General information

• Please read and follow these safety instructions.

• Keep them safe for future reference.

• Observe all warnings on the speaker and in the manual. Please check the speaker for damage before

use. The speaker must be in perfect working condition. Damaged parts may lead to personal injury.

2. Use only as directed

• Connect the speaker(s) according to the instructions in the manual.

• Many ELAC speakers are equipped with spikes and/or anti-slip feet. They are explicitly provided for

leveling the speaker. For leveling on an uneven ﬂoor, unscrew the spikes or anti-slip feet by 2-3 turns of

thread. The speaker should always be in perfect vertical alignment: the stability of the speaker must not

be compromised by using spikes or anti-slip feet as the speaker may tip-over.

3. Location

• Install the speakers on a level surface only

• When choosing the location of these speakers do not place them in locations that are:

• In direct sunlight

• Very humid

• Prone to vibrations

• Exceptionally hot or cold

• Near CRT Televisions (the speakers are not magnetically shielded and may cause color issues

with a CRT based TV)

• Close to magnetic cards (Since the speakers are not magnetically shielded placing magnetic

cards such as credit cards or commuter cards may cause them to fail).

WARNING! Please ensure the product is perfectly stable to avoid injury from tip-over. Please note, that stability

can be increased by using spikes on carpeted surfaces. However, the mounting of spikes must be carried out

carefully due to their very sharp ends which may cause injuries. The stability on slippery ﬂoors can be increased

by using Velcro fastening tape or double-sided adhesive tape. Do not install the speaker near any heat sources

such as radiators, heating valves, stoves, or other apparatus (including ampliﬁers) that produce heat, or in areas

where there is a risk of explosion.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not install the speaker in a closed rack or in a closed cupboard.

• Do not put burning candles on or near the speaker.

• Do not install the speaker near transformers because electromagnetic stray ﬁelds can cause hum noise

on woofers.

• In combination with certain materials / lacquers / material surfaces, anti-slip feet or spike washers may

cause colored imprints on the surfaces.

SAFETY INSTRUCTIONS

ELAC DEBUT ConneX DCB41 | www.elac.com | Page 9

4. Overload

Extreme overload of the device due to very high volume may cause individual components to blow.

Because of the possible danger, you should never leave loudspeakers under extreme overload

conditions unattended.

5. Service

DANGER! Do not open the cabinet because the components and conductors may carry dangerous

levels electricity! Servicing to be carried out by qualiﬁed service personnel only.

Servicing is required when the loudspeaker has been damaged in any way, such as damage to

the power supply cord or the plug, or when liquid has been spilled or objects have fallen into the

loudspeaker, the speaker has been exposed to rain or moisture, does not operate normally, or has

been dropped. To reduce the risk of electric shock, do not open the loudspeaker. Servicing to be

carried out by qualiﬁed service personnel only.

6. Fuse links

Various faults in subwoofers or active speakers may cause the fuse to blow. If the fuse blows, only

replace it with the correct fuse type and rating as shown on the rear of the loudspeaker on the fuse

holder. A second fuse is included with the device (in the fuse holder beneath the main socket).

7. Cleaning

NOTE: Clean only with soft, smooth cloth or with dust brush. Do not use scouring agents, alcohol,

benzene, furniture polish or other agents for cleaning! Modern furniture is often coated with multiple

varnishes and plastics which can be treated with chemical agents. Some of these agents contain

substances which degrade or soften the rubber feet. Therefore we advise you to place an anti-slip

mat underneath the loudspeaker.

8. Volume

CAUTION! Continuous high volume may cause severe damage to your hearing. Please listen

responsibly.

9. Disposal

The packaging is made from recyclable materials. Dispose of this in an environmentally friendly

manner. At end of life do not dispose the speaker with the standard household waste. The speaker

must be recycled in accordance with local legislation. Ask your local government for further

information on recycling as the device contains valuable raw materials. Disable the speaker before

disposal.

10. Power

This subwoofer is only intended to be connected to voltages that are listed on the rear panel of the

cabinet. Connection to any other voltage may cause irreversible damage to the subwoofer and will

void the warranty. Use of plug adapters is not recommended because they may allow connection to

voltages other than those printed on the back of this subwoofer.

ELAC DEBUT ConneX DCB41 | www.elac.com | Page 10

Andere Handbücher für DCB41

Inhaltsverzeichnis

Andere ELAC Sprecher Handbücher

ELAC

ELAC Vertex III Series Bedienungsanleitung

ELAC

ELAC Muro Series Bedienungsanleitung

ELAC

ELAC Adante AS-61 Bedienungsanleitung

ELAC

ELAC Contractor Series IC-C61-W Bedienungsanleitung

ELAC

ELAC A4 Bedienungsanleitung

ELAC

ELAC Debut Reference DBR62 Bedienungsanleitung

ELAC

ELAC SB-VJ41L Bedienungsanleitung

ELAC

ELAC Discovery Z3 Bedienungsanleitung

ELAC

ELAC Navis AB-51 Bedienungsanleitung

ELAC

ELAC UB5 Bedienungsanleitung

ELAC

ELAC Debut Reference DBR62 Bedienungsanleitung

ELAC

ELAC UB5 Bedienungsanleitung

ELAC

ELAC Uni-Fi UF5IFS U5 Bedienungsanleitung

ELAC

ELAC Adante AS-61 Bedienungsanleitung

ELAC

ELAC AM 200 Bedienungsanleitung

ELAC

ELAC Vertex III Series Bedienungsanleitung

ELAC

ELAC Uni-Fi Reference UBR62 Bedienungsanleitung

ELAC

ELAC LA JET 10 Bedienungsanleitung

ELAC

ELAC WS 1425 Bedienungsanleitung

ELAC

ELAC AIR-X Bedienungsanleitung

ELAC

ELAC ARB-51 Bedienungsanleitung

ELAC

ELAC FS 249 Bedienungsanleitung

ELAC

ELAC DEBUT SERIES Bedienungsanleitung

ELAC

ELAC IW 1130 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung