Elastix NLX4000 Bedienungsanleitung
Elastix NLX4000
User Manual
www.elastix.com
1
Copyright
Copyright
©
2013 Elastix Inc. All rights reserved. No part of this document may be
reproduced without prior written permission.
Disclaimer
Elastix Inc. reserves the right to modify the design, characteristics, and products at
any time without notification or obligation and shall not be held liable for any error or
damage of any kind resulting from the use of this document.
Elastix has made every effort to ensure that the information contained in this
document is accurate and complete; however, the contents of this document are
subject to revision without notice. Please contact Elastix to ensure you have the latest
version of this document.
Trademarks
All other trademarks mentioned in this document are the property of their respective
owners.
FCC warning statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
www.elastix.com
2
Recycling / disposal
Do not discard electronic products in household trash!
All waste electronics equipment should be recycled according to local regulations.
Safety information
Electrical safety
•
To prevent electrical shock hazard, disconnect the power cable from the electrical
outlet before relocating the system.
•
When adding or removing devices to or from the system, ensure that the power
cables for the devices are unplugged before the signal cables are connected.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer.
Operation safety
•
Before installing devices into the system, carefully read all the documents that
came with the package.
•
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
•
Avoid dust, humidity, and temperature extremes. Do not place the product in any
area where it may become wet. Place the product on a stable surface.
•
If you encounter technical problems with the product, contact a qualified
service technician or your retailer.
----------------------------------------------------
Lithium-Ion Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturerís instructions.
www.elastix.com
3
Chapter 1 System introduction
1.1 Welcome!
This chapter lists the system features, including introduction on the front and rear
panel, and internal components, Thank you for choosing the elastix NLX4000.
The system motherboard supports the Intel Atom N2600XX/D2500XX series processors
and combined with the Intel NM10 Chipset to set a new benchmark for an effective
desktop platform solution.
The system supports up to 4GB of system memory using DDR3 1333MHZ SODIMMs,
high-resolution graphics integrated graphics controller .serialATARAID, USB 2.0, and
PCIe x4 solt.
1.2 Front panel
The front panel include LCD panel display and control buttons, power button .
1. Power button , press this button to turn the system on.
2. Lcd panel display, the Lcd panel can display various operating states of the
system.
3. Lcd panel control buttons. Enter function.
4. Lcd panel control buttons. Down function.
5. Lcd panel control buttons. Exit function.
6. Lcd panel control buttons. Up function.
www.elastix.com
4
1.3 Rear panel
The system rear panel includes power connector and several I/O ports that allow
convenient connection of devices.
1.
Expansion slot covers. Remove these cover when installing expansion cards.
Expansion card is replaceable.
2.
VGA port. This port connected with a VGA monitor.
3.
LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network
(LAN) through a network hub.
4.
LAN(RJ-45) port. This port allows Gigabit connection to a Local Area Network
(LAN) through a network hub.
5. USB 2.0 ports 1 and 2. These 4-pin Universal Serial Bus (USB) ports are
available for connecting USB 2.0 devices
6.
Power connector. This connector is used for the power cable and plug. (input
AC100V_240V)
1.4 Internal components
The illustration below is the internal view of the system when you remove, the top
cover and the power supply unit. The installed components are labeled for your
reference.
www.elastix.com
5
1.
Power supply unit
2. Hard disk power support
3. SATA connectors
4. GPIO connectors
5. USB connector
6. LCD panel display connectors
7. Motherboard power connector
8.
Expansion slot
9.
Power button connectors’ cable
Chapter 2 System introduction
This chapter provides instructions on how to install components in the system
step-by-step.
2.1 Preparation
Before you proceed, make sure that you have all the components you plan to install in
the system.
Basic components to install
1. Motherboard
2. DDR Memory Module (SODIMM)
3. Expansion solts
4. Hard disk drive
5. Optical drive
www.elastix.com
6
Tool
Phillips (cross) screw driver
2.2 Before you proceed
Take note of the following precautions before you install components into the system.
•Use a grounded wrist strap or touch a safely grounded object or a metal object,
such as the power supply case, before handling components to avoid damaging them
due to static electricity.
•Hold components by the edges to avoid touching the ICs on them.
•Whenever you uninstall any component, place it on a grounded antistatic pad
or in the bag that came with the component. The motherboard comes with an onboard
standby power LED. This LED lights up to indicate that the system is ON, in sleep
mode or in soft-off mode, and not powered OFF. Unplug the power cable from the
power outlet and make sure that the standby power LED is OFF before installing any
system component.
2.3 Installing a SODIMM
The system motherboard has a DDR3 Memory (SODIMM) sockets which supports up
to 4GB Memory.
The following figure illustrates the location of the sockets
2.4 Expansion slots
Elastix NLX4000 Based on plug-in modular design.
It allows users to integrate up to 2 pieces of PCI-E x1 telephony cards and supports
to combine with analog, BRI, PRI, GSM .
www.elastix.com
7
Chapter 3 Motherboard info
This chapter gives information about the motherboard that comes with the system.
This chapter includes the motherboard layout, jumper settings, and connector
locations.
3.1 Specification
CPU: Intel Atom N2600_1.6Ghz/D2500_1.86Ghz/D2550_1.86Ghz
DRAM: Slot Onboard, up to 4GB DDR3 1333 SDRAM ( Atom N2600 only
support 2GB)
Chipset: Intel NM10 Express Chipset
Southbridge: Intel NM10
Storage: 1 SATA slot, 1 mSATA Socket
Three front panel LEDs, for 3 programmable GPO status indicator
Push button: for mode setting switch, accessing a programmable GPI, active low
means switch is pressed
PCIe Interface : PCIe x4 Golden Finger
Expansion: 1 Mini PCIe slot
Connectivity: Up to 2 Ethernet channels (10/100/1000Mbps speed)
2 PCIe Ethernet controllers
Support PXE (for remote booting)
I/O: 1*DB15 VGA port, 5*USB 2.0 port
Board size: 6 x 6" (152.4 x 152.4 mm)
Temperature: 0°C to 60°C (contact factory for more temp. options)
Firmware: AMI_UEFI BIOS
PCB layer: 4
Power dissipation: ~7.8W (Minimum Power Dissipation)
www.elastix.com
8
3.2 Motherboard layout
3.3 Connector and Jumper List
Name Function
VGA1 VGA display output
CN10 PCIe x4 Golden Finger
JP1 Clear CMOS
CN15 Main Power in Jacket
CN16 Power Supply Jacket
U4 DDR3 Memory Slot
CN11 mSATA Slot
CN13 Mini PCIe Slot
CN2 Ethernet 1
CN3 Ethernet 2
CN5 SATA Interface
CN4 SATA power supply
CN8 USB Port
CN1 LPC interface
www.elastix.com
9
JP5 Manual Reset In
CN6 External LEDs and GPIO
CN18/CN9 USB connector
CN14 SIM Socket
FAN1 FAN power supply
SW1 GPI switch
3.4 Specification
CPU: Intel Atom N2600_1.6Ghz/D2500_1.86Ghz/D2550_1.86Ghz
DRAM: Slot Onboard, up to 4GB DDR3 1333 SDRAM ( Atom N2600 only
support 2GB)
Chipset: Intel NM10 Express Chipset
Southbridge: Intel NM10
Storage: 1 SATA slot, 1 mSATA Socket
Three front panel LEDs, for 3 programmable GPO status indicator
Push button: for mode setting switch, accessing a programmable GPI, active low
means switch is pressed
PCIe Interface : PCIe x4 Golden Finger
Expansion: 1 Mini PCIe slot
Connectivity: Up to 2 Ethernet channels (10/100/1000Mbps speed)
2 PCIe Ethernet controllers
Support PXE (for remote booting)
I/O: 1*DB15 VGA port, 5*USB 2.0 port
Board size: 6 x 6" (152.4 x 152.4 mm)
Temperature: 0°C to 60°C (contact factory for more temp. options)
Firmware: AMI_UEFI BIOS
PCB layer: 4
Power dissipation: ~7.8W (Minimum Power Dissipation)
3.5 Connector and Jumper Description
JP1 clear CMOS
Setting Function
Close 1-2 Clear CMOS
Open 1-2 (default) Normal
CN15 Main Power Jacket DC in @12V
Andere Handbücher für NLX4000
1
Inhaltsverzeichnis
Beliebte Telefonanlage Handbücher anderer Marken
Allo.com
Allo.com Nano 2 Bedienungsanleitung
ZYCOD
ZYCOD ZX50 Bedienungsanleitung
Panasonic
Panasonic KX-TDA100BX Bedienungsanleitung
LV switch
LV switch IPPBX800 Gebrauchsanweisung
Edge-Core
Edge-Core VST3305 Bedienungsanleitung
Panasonic
Panasonic KX-T7625 - Digital Proprietary Speakerphone 24... Bedienungsanleitung
Rauland-Borg
Rauland-Borg Telecenter IV Bedienungsanleitung
Grandstream Networks
Grandstream Networks UCM6208 Bedienungsanleitung
ATCOM
ATCOM IPPBX IP02 Bedienungsanleitung
Panasonic
Panasonic KX-TVS50 - 2 Port Voicemail System Bedienungsanleitung
bintec elmeg
bintec elmeg elmeg hybird 600 Bedienungsanleitung
Panasonic
Panasonic KX-NS300 Bedienungsanleitung
