Elation Design LED 36 Tri-Brick Bedienungsanleitung
Rev. 11/17/06
Design LED 36
Elation Professional™
4295 Charter Street
Los Angeles, Ca 90058
www.elationlighting.com
DESIGN LED 36™
©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.com
DESIGN LED 36™
©Elation Professional, Los Angeles Ca. 2 www.ElationLighting.com
TABLE OF CONTENS
CONTENTS
1. General Information……………………………………………………………………… 3
a. Introduction………………………………………………………………………. 3
b. Unpacking………………………………………………………..…………..… 3
c. Customer Support…………………………………………….………………… 3
d. Warranty Registration……………………………………………………..…… 4
2. Safety Instructions………………………………………………………........…………. 5
3. Features…………………………………………………………………………………… 7
4. General Guidelines………………………………………………………………………. 8
5. Fixture Overview…………………………………………………………………………. 9
6. Mounting and Installation………………………………………………………….……. 11
a. Mounting Positions……………………………………………………………… 11
b. Mounting Points…………………………………………………………………. 12
c. Securing………………………………………………………………………….. 13
7. Understanding DMX……………………………………………………………………... 14
a. DMX Connections………………………………………………………………. 14
b. DMX Terminator…………………………………………………………………. 15
c. 3-Pin to 5-Pin Conversion………………………………………………………. 16
d. Understanding DMX Addressing.……………………………………………… 16
8. Manual Operation….…………………………………………………………………….. 17
9. DMX Operation…….…………………………………………………………………….. 19
a. DMX Channel Values (6 Channel Mode)…………………………………….. 19
b. DMX Channel Values (3 Channel Mode)…………………………………….. 21
c. DMX Dipswitch Chart…………………………………………………………… 23
10. Cleaning and Maintenance……………………………………………………………… 24
11. Warranty…………………………………………………………………………………... 25
12. Photometric Data………………………………………………………………………… 27
13. Dimensional Drawings………………………………………………….……………….. 28
14. Circuit Schematic………...………………………………………………………………. 29
15. Technical Specifications…………………………………………...………….………… 30
DESIGN LED 36™
©Elation Professional, Los Angeles Ca. 3 www.ElationLighting.com
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and
reliable LED fixtures on the market today! The DESIGN LED 36,™ has been designed to
perform reliably for years when the guidelines in this booklet are followed. Please read and
understand the instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information regarding safety during
use and maintenance.
UNPACKING: Thank you for purchasing the DESIGN LED 36™ by Elation Professional®.
Every DESIGN LED 36™ has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may have
occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture
for damage and be sure all accessories necessary to operate the fixture have arrived intact.
In the event damage has been found or parts are missing, please contact our customer
support team for further instructions. Inside the box you should find: the fixture, a DMX XLR
cable, a safety cable, and this manual. Please do not return this unit to your dealer without
first contacting customer support at the number listed below.
CUSTOMER SUPPORT:Elation Professional®provides a customer support line, to provide
set up help and to answer any question should you encounter problems during your set up
or initial operation. You may also visit us on the web at www.elationlighting.com for any
comments or suggestions. For service related issue please contact Elation Professional®.
Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice: (323) 582-3322
Fax: (323) 582-3108
E-mail: [email protected]
Forum: www.ElationLighting.com/forum
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to
rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
DESIGN LED 36™
©Elation Professional, Los Angeles Ca. 4 www.ElationLighting.com
yourself. Doing so will void your manufactures warranty.
Please do not discard the shipping carton in the trash. Please recycle whenever possible.
WARRANTY REGISTRATION: The DESIGN LED 36™ carries a two year (730 days)
limited warranty. Please fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written
on the outside of the return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included in the shipping
container. If the unit is under warranty, you must provide a copy of your proof of purchase
invoice. Items returned without a R.A. number clearly marked on the outside of the package
will be refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support at (323) 582-3322.
DESIGN LED 36™
©Elation Professional, Los Angeles Ca. 5 www.ElationLighting.com
2. SAFETY INSTRUCTIONS
To guarantee proper and consistent operation, it is important to
follow the guidelines in this manual. Elation Professional will not
accept responsibility for damages resulting from the misuse of
this fixture due to the disregard of the information printed in this
manual.
1. Always be sure that the fan and the air inlets remain clean and are never
blocked. Allow about 6” (15cm) between this fixture and other devices or a wall
to allow for proper cooling.
2. Never touch the fixture during normal operation.
3. Never look directly into the lamp beam. You risk injury to your retina, which
may induce blindness.
4. For safe operation, follow the Installation guide described in chapter two of this
manual. Operating the Design LED 36™ without suited safety aids such as
safety cables or clamps can increase the risk of damage and/or personal injury.
5. Installation should only be performed by qualified and certified personal.
6. When mounting this fixture, use only the original rigging points included with
this fixture. Any structural modification will void the original manufactures
warranty and may increase the risk of damage and/or personal injury.
7. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.
8. Do not attempt to operate this fixture if the power cord has become damaged or
frayed.
9. Never open this fixture while in use.
10.This device falls under protection-class I. Therefore it is essential that the
device be grounded properly.
11.All electrical connections must performed by qualified personal.
12.Be sure the available voltage matches the voltage requirements of the unit. Be
sure the power cord is never crimped or damaged. If the power cord is
DESIGN LED 36™
©Elation Professional, Los Angeles Ca. 6 www.ElationLighting.com
damaged, replace it immediately with a new one of similar power rating.
13.Always disconnect from main power before performing any type of service or
any cleaning procedure.
14.Only handle the power cord by the plug. Never pull out the plug by tugging the
wire portion of the cord.
15.Please be aware that damages caused by manual modifications to the
device are not subject to warranty.
Important Notice: Damages resulting from the disregard of safety and general user
instructions found in this user manual are not subject to any warranty claims.
Never look directly into the light source,
as sensitive persons may suffer an epileptic shock.
Never touch the device during operation!
The housing may heat up
DESIGN LED 36™
©Elation Professional, Los Angeles Ca. 7 www.ElationLighting.com
3. FEATURES
• Low power consumption
• Minimal heat emission
• Maintenance free operation
• Equipped with 36 one-watt LEDs: (12 red, 12 blue, 12 green)
• High power LEDs manufactured by Lumileds, USA
• 50,000 hours plus, LED life
• Step less RGB color changing
• Strobe-effect with a maximum flash rate of 18fps
• DMX-controlled operation or stand-alone operation with Master/Slave-function
• 8 built-in programs can be called up via DMX-controller
~ 48 preprogrammed scenes per a program
• Sound-controlled via built-in microphone
• 6 DMX-channel or 3 DMX-channel operation
• DMX-control via standard DMX-controller
• Flicker-free operation for television and film
• Compact design: fits in 12” box truss
• Brilliant light output
DESIGN LED 36™
©Elation Professional, Los Angeles Ca. 8 www.ElationLighting.com
4. GENERAL GUIDELINES
This fixture is a professional lighting effect designed for use on stage, in nightclubs, in
theatres, and other types of architectural installations. Do not attempt operation or
installation without a proper knowledge on how to do so.
This fixture was designed for indoor use only; use of this fixture outside will void the
manufacture’s warranty.
Consistent operational breaks will ensure that the fixture will function properly for many
years to come.
Do not shake the fixture around. Avoid brute force when installing or operating the fixture.
While choosing an installation location, please be sure that the fixture will not be exposed to
extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or
flat surface should be at least .5 meter (about 1.5ft).
Always install the fixture with an appropriately rated safety cable. When installing the fixture
in a suspended environment always be sure to use mounting hardware no less than M10 x
25 mm, also be sure the hardware is only inserted in the yoke’s mounting holes.
Do not attempt to operate this fixture until you have familiarized yourself with all of its
functions.
Do not permit operation by persons not qualified for operating this type of theatrical fixture.
Most damages are the result of improper operation.
Please use the original packaging to transport the fixture in for service.
For your own safety, please read this user manual carefully before installing the device.
DESIGN LED 36™
©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.com
5. FIXTURE OVERVIEW
1. Venting Slots – These slots are designed to keep the fixture cool during operation.
Never block these slots. Keep these slots clean at all times.
2. Exterior Housing – The exterior housing is constructed of rugged polymer material.
3. Hanging Bracket – The unit uses a unique sectional bracket that allows the unit to be
1. Venting Slots
2. Exterior Housing
3. Hanging Bracket
4. Diffusion Lens
5. LED Assembly
6. Power Cord
7. On/Off Switch
8. DMX In Jack
9. DMX Out Jack
10.Fuse Holder Housing
11.Dipswitch Assembly
Andere Handbücher für Design LED 36 Tri-Brick
2
Inhaltsverzeichnis
Andere Elation Beleuchtungsausrüstung Handbücher
Elation
Elation POWER SPOT 700CMY Bedienungsanleitung
Elation
Elation Level Q7 IP Bedienungsanleitung
Elation
Elation Opti Tri 30 Bedienungsanleitung
Elation
Elation Design Spot 300E Bedienungsanleitung
Elation
Elation Design LED 36MH Bedienungsanleitung
Elation
Elation Eled Light Bedienungsanleitung
Elation
Elation KL FRESNEL 8 PO Bedienungsanleitung
Elation
Elation Design Par 575H Bedienungsanleitung
Elation
Elation Design LED 36 Brick Bedienungsanleitung
Elation
Elation WW PROFILE HP IP Bedienungsanleitung
Elation
Elation KL PAR FC Bedienungsanleitung
Elation
Elation ELAR EXFLOOD Bedienungsanleitung
Elation
Elation Waterfall 250 Bedienungsanleitung
Elation
Elation EVLED1024SMD Video Wall Bedienungsanleitung
Elation
Elation CUEPIX STRIP TRI Bedienungsanleitung
Elation
Elation VISION 575 Bedienungsanleitung
Elation
Elation KL PANEL PO Bedienungsanleitung
Elation
Elation Pixel Driver 170 Bedienungsanleitung
Elation
Elation ELAR EXTQW FLOOD HP Bedienungsanleitung
Elation
Elation Focus Spot 250R Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
