Eldes ESIM120 Bedienungsanleitung

ESIM120

GSM SWITCHGATE CONTROLLER

EN ESIM120 Manual v.3.6

User Manual v3.6

Valid for ESIM120 v21.05.00 and up

SAFETY INSTRUCTIONS

Please read and follow these safety guidelines to safeguard yourself and others:

• GSM switch-gate controller ESIM120 (later referred to as “the system” or “ the device”) contains a built-in radio transceiver operating in

GSM 850/900/1800/1900 MHz bands.

• DO NOT use the system where it can cause potential danger and interfere with other devices – such as medical devices.

• DO NOT use the system in hazardous environment.

• DO NOT expose the system to high humidity, chemical environment or mechanical impact.

• DO NOT attempt to repair the system yourself – any repairs must be carried out by fully qualied personnel only.

Disconnect the mains power before installing. Never install or carry out maintenance during stormy weather. The electric sock-

et that powers the system must be easily accessible.

Please use the 10-24V 50Hz ~200mA AC or 10-24V 200mA DC power supply unit that meets the EN 60950-1 standard.

Any additional device you connect to the system, such as a computer, must also be powered by an EN 60950-1 approved

supply. When connecting the power supply to the system, switching the polarity terminal places does not have any aect.

External power supply can be connected to AC mains only inside installation room

with automatic 2-pole circuit breaker capable of disconnecting circuit in the event of

short circuit or over-current condition. Open circuit breaker must have a gap between

connections of more than 3mm (0.12in) and the disconnection current 5A.

Phase

AC 230V

50 Hz/DC 24V

USB cable

Null

ESIM120

AC/DC

To switch the system o, unplug the external electric power supply from or any other linked device that the system is powered

from.

A blown fuse cannot be replaced by the user. The replacement fuse has to be of the kind indicated by the manufacturer (fuse

F1 model – MINISMDC050F 0.5A).

If you use a computer for the device conguration, it must be earthed.

The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that the

product must not be disposed of together with household waste. To prevent possible harm to human health and/or the envi-

ronment, the product must be disposed on in an approved and environmentally safe recycling process. For further information

on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste disposal

in your area.

ESIM120 Manual v.3.6

CONTENTS

1. GENERAL INFORMATION ...........................................................................................................................................................6

2. TECHNICAL SPECIFICATIONS ....................................................................................................................................................6

2.1. Electrical and Mechanical Characteristics.....................................................................................................................................................6

2.2. Main Unit, LED Indicator and Connector Functionality ...............................................................................................................................7

2.3. Wiring Diagrams ................................................................................................................................................................................................8

3. INSTALLATION ...........................................................................................................................................................................9

4. GENERAL OPERATIONAL DESCRIPTION..................................................................................................................................10

5. CONFIGURATION METHODS ....................................................................................................................................................10

5.1. SMS Text Messages.........................................................................................................................................................................................10

5.2. ELDES Conguration Tool Software.............................................................................................................................................................10

5.2.1. Remote Connection ........................................................................................................................................................................................10

5.2.2. Ending the Remote Connection Session.....................................................................................................................................................10

6. SYSTEM LANGUAGE................................................................................................................................................................. 11

7. SMS PASSWORD.......................................................................................................................................................................11

8. ADMINISTRATOR PHONE NUMBERS.......................................................................................................................................12

9. DATE AND TIME........................................................................................................................................................................13

9.1. Automatic Date and Time Synchronization ................................................................................................................................................13

10. USER PHONE NUMBER DATABASE.........................................................................................................................................14

10.1. User Validity and Access Restriction ...........................................................................................................................................................16

11. OUTPUTS ................................................................................................................................................................................18

11.1. Output Names..................................................................................................................................................................................................18

11.2. Output Control by Free of Charge Phone Call .............................................................................................................................................18

11.3. Output Control by SMS Text Message..........................................................................................................................................................19

11.4. Output Control Conrmation by Call Back ...................................................................................................................................................21

11.5. Output Control from any Phone Number.....................................................................................................................................................21

11.6. Automatic Output Control..............................................................................................................................................................................22

12. SCHEDULERS ..........................................................................................................................................................................23

13. EVENT LOG ..............................................................................................................................................................................25

14. INPUTS................................................................................................................................................................................... 26

14.1. Input Names and Alarm Notications......................................................................................................................................................... 26

14.2. Disabling and Enabling Inputs.......................................................................................................................................................................27

15. SYSTEM INFORMATION. INFO SMS........................................................................................................................................ 28

15.1. Periodic Info SMS............................................................................................................................................................................................ 28

16. SYSTEM NOTIFICATIONS ....................................................................................................................................................... 29

16.1. SMS Text Message Delivery Restrictions ................................................................................................................................................... 29

16.2. SMSC (Short Message Service Center) Phone Number............................................................................................................................ 29

17. GPRS NETWORK SETTINGS ................................................................................................................................................... 30

18. INCOMING PHONE NUMBER VERIFICATION SETTINGS .........................................................................................................31

19. REMOTE SYSTEM RESTART....................................................................................................................................................31

20. TECHNICAL SUPPORT ............................................................................................................................................................32

20.1. Troubleshooting ..............................................................................................................................................................................................32

20.2. Restoring Default Parameters ......................................................................................................................................................................32

20.3. Updating the Firmware via USB Cable.........................................................................................................................................................32

21. ELDES CLOUD SERVICES .........................................................................................................................................................33

22. RELATED PRODUCTS ............................................................................................................................................................. 34

EN ESIM120 Manual v.3.6

ESIM120 Manual v.3.6

Limited Liability

The buyer agrees that the system will reduce the risk of re, theft, burglary or other danger but that it does not guarantee against the oc-

currence of such events. “ELDES UAB” will not take any responsibility for the loss of personal eects, property or revenue whilst using the

system. The liability of “ELDES UAB” is limited to the value of the system purchased. “ELDES UAB” is not aliated with any mobile/wireless/

cellular provider and is therefore not responsible for the quality of such services.

Manufacturer Warranty

The system carries a 24-month manufacturer warranty from “ELDES UAB”. The warranty begins the day the system is purchased by the

user and the receipt must be retained as proof of purchase date. The warranty remains valid only if the system is used as intended, fol-

lowing all guidelines outlined in this manual and in accordance with the operating conditions specied. The warranty is void if the system

has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous environments or force majeure factors.

Dear Customer,

Thank you for choosing to purchase the GSM switch-gate controller ESIM120. Your thoughtful decision will ensure reliable solution for

many years as all ELDES products are manufactured to meet the highest standards.

We are condent that you will be completely satised with your product. However, in the unlikely event that you do experience a

problem, please contact the dealer from whom you made your purchase.

UAB ELDES

www.eldes.lt

Contents of Pack

Item Quantity

1. ESIM120...................................................1

2. User manual............................................1

3. GSM/GPRS antenna...............................1

Not included:

• SIM card – we recommend you get a contract SIM, not Pay As You Go.

• mini-USB cable – can be obtained from your local distributor.

It is strictly forbidden to copy and distribute information in this document or pass to a third party without an

advanced written authorization from “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this

document and/or related products without a warning. Hereby, “ELDES UAB” declares that the GSM switch-gate

controller ESIM120 is in compliance with the essential requirements and other relevant provisions of Directive

1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt.

EN ESIM120 Manual v.3.6

1. GENERAL INFORMATION

ESIM120 is a micro-controller based device intended to provide access control for gate automatics, road barriers or to remotely turn ON/OFF

any electrical appliance via the GSM network.

Examples of using the system:

• Access control.

• Parking lot control of residential houses or oces.

• Gate control of private houses.

• Any electrical appliance control: lighting, watering, heating etc.

• Remote reboot of the “frozen” systems, such as computer network or a server.

Main features

• Manual output control by free of charge phone call.

• Automatic output control in accordance with the scheduled time.

• Congurable output pulse duration.

• Automatic date and time synchronization.

• Up to 5 administrators for system conguration by SMS text messages, acceptance of input alarm SMS text messages, output control

by SMS text message and free of charge phone call.

• User database capacity – up to 2000 users for output control by free of charge phone call.

• User phone number validity limitation in accordance with a set deadline (date/time) or number of rings to the system.

• Output control restriction for users in accordance with the specied weekdays and time.

• Event log of 1000 events containing date and time as well as administrator/user phone number and user name who controlled the

output.

• 3 inputs with customizable alarm texts for notication on gate state or in case it gets jammed.

• Periodic self-test notication by SMS text message to administrator phone number.

2.TECHNICAL SPECIFICATIONS

2.1. Electrical and Mechanical Characteristics

Supply voltage...............................................................10-24V 50Hz ~ 200mA max / 10-24V 200mA max

Current used in idle state.............................................up to 50mA

GSM modem frequency................................................850/900/1800/1900 MHz

Number of outputs .......................................................2

Output type....................................................................Relay; NO (normally-open) or NC (normally-closed) - congurable

Maximum commuting output values.........................24V 50Hz ~ 0,5A / 24V 1A

Number of low-level (negative) inputs .....................2

Number of high-level (positive) inputs.....................1

Low-level (negative) input value range....................0... 16V -0.8... -0.4mA

High-level (positive) input value range.....................5... 50V 0.17 .... 1.7mA

Low-level (negative) and high-level .........................NO (normally-open)

(positive) input connection type

Dimensions ....................................................................87x107x29mm (3.43x4.21x1.14in)

Operating temperature range ....................................-20…+55 °C (-30...+55 °C with limitations) (-4... +131°F (-22... +131°F))

Humidity.........................................................................0-90% RH @ 0... +40°C (0-90% RH @ +32... +104°F) (non-condensing)

ESIM120 Manual v.3.6

2.2. Main Unit, LED Indicator and Connector Functionality

AC/DC RELAY1 RELAY2 COM Z5 Z4 Z3 Z2 Z1

ANT

MIC

USB

SIM CARD

G S M

MO DE M

SIM STAT

NETW

DEF

Main Unit Functionality

ANT GSM/GPRS antenna SMA type connector

USB Mini USB port

SIM CARD SIM card slot / holder

GSM MODEM GSM network 850/900/1800/1900 MHz modem

MIC N/A

SIM STAT Red light-emitting diode indicating SIM card status

NETW Green light-emitting diode indicating GSM signal strength

DEF Pins for restoring default settings

F1 0.5A fuse

Connector Functionality

AC/DC Power supply terminals

RELAY1 Output C1 terminal

RELAY2 Output C2 terminal

COM Common terminal

Z5 N/A

Z4 N/A

Z3 Low-level (negative) input terminal

Z2 High-level (positive) input terminal

Z1 Low-level (negative) input terminal

EN ESIM120 Manual v.3.6

LED Indicator Functionality

SIM STAT indication SIM card status

OFF No mains power / micro-controller fault

Steady ON SIM card is attempting to connect to the GSM network / SIM card is not present / PIN code enabled

Flashing GSM connection failed

NETW indication GSM signal strength

OFF No GSM signal

Flashing every 1 sec. Poor

Flashing several times per sec. Medium

Steady ON Excellent

2.3. Wiring Diagrams

General wiring

ESIM120

AC/DC

Power

supply

GATE

AUTOMATION

DEVICE

RELAY2RELAY1 COM Z3 Z2 Z1

Example of ESIM120 system wiring to gate automation device

FO Fault output; open

collector type

+24V Power supply

output for powering

aux. equipment

Pulse input

GND Common terminal

ESIM120 GATE AUTOMATION DEVICE

AC/DC RELAY1 RELAY2 COM Z5 Z4 Z3 Z2 Z1 F0 +24vGND

ESIM120 Manual v.3.6

3.INSTALLATION

• The system should be installed indoors, in stationary environment ONLY.

• For the connection of input/output terminals, use 0.50 mm2(0.02in2) thread unshielded cable of up to 100m (328.08ft) length.

1. Wire up the system in accordance with the wiring diagrams (see 2.3 Wiring Diagrams for more details).

2. Connect the GSM/GPRS antenna. Based on the type of the GSM/GPRS antenna supplied with ESIM120 unit, follow the recommenda-

tions for the antenna installation:

GSM/GPRS

antenna

Never install in the following

locations:

• inside the metal cabinet

• closer than 20cm (7.87in) from the

metal surface and/ or power lines

3. Disable the PIN code request of the SIM card by inserting it into a mobile phone and following the proper menu steps.

4. Once the PIN code is disabled, insert the SIM card into the SIM card slot / holder of ESIM120 system.

5. Power up the system and wait until indicator SIM STAT lights up indicating SIM card status.

6. Once the indicator SIM STAT lights OFF, the illuminated indicator NETW lights up indicating that the system has successfully connected

to the GSM network. To nd the strongest GSM signal, position the GSM/GPRS antenna and follow the indications provided by NETW

indicator (see 2.2. Main Unit, LED Indicator and Connector Functionality for more details).

7. Change the system language if necessary (see 6. SYSTEM LANGUAGE for more details).

8. Change the default SMS password (see 7. SMS PASSWORD for more details).

9. Set the phone number for Admin 1 (see 8. ADMINISTRATOR PHONE NUMBERS for more details).

10. Set system date and time (see 9. DATE AND TIME for more details).

11. Once the system is fully congured, it is ready for use. However, if you fail to receive a reply by SMS text message from the system,

please check the SMSC (Short Message Service Center) phone number. For more details regarding the SMS center phone number,

please refer to 16.2. SMSC (Short Message Service Center) Phone Number.

ATTENTION: The system is NOT compatible with pure 3G SIM cards. Only 2G/GSM SIM cards and 3G SIM cards with 2G/GSM prole en-

abled are supported. For more details, please contact your GSM operator.

ATTENTION: We also recommend you to disable call forwarding, voice mail/text message reports on missed/busy calls and

similar services that might cause incorrect system operation. Please contact your GSM operator for more details on these services and

how to disable them.

NOTE: For maximum system reliability we recommend you do NOT use a Pay As You Go SIM card. Otherwise, in the event of insucient

credit balance on the SIM card, the system would fail to make a phone call or send SMS text messages.

NOTE: We advise you to choose the same GSM SIM provider for your system as for your mobile phone. This will ensure the fastest, most

reliable SMS text message delivery service and phone call connection.

NOTE: Even though the installation process of ESIM120 is not too complicated, we still recommend to perform it by a person with basic

knowledge in electrical engineering and electronics to avoid any system damage.

EN ESIM120 Manual v.3.6

4.GENERAL OPERATIONAL DESCRIPTION

When a phone call is made to the phone number of the SIM card inserted in ESIM120, the system will verify if the caller’s phone number ex-

ists in the memory. If the caller is one of the 5 administrators or the phone number belongs to one of the 2000 database users, the system

will reject the phone call, thus making the phone call free of charge, and open the gate. By ringing to ESIM120 again, it will close the gate.

If the phone number is not recognized, the system will reject the phone call and ignore it. The GSM switch-gate controller can also control

your gate automatically in accordance with the scheduled time or by sending an SMS text message from the administrator’s phone number.

By connecting a sensor to one of the 3 inputs, the administrators can receive SMS text messages regarding the gates that failed to close

during the set time period.

User/Admin

ESIM120

CALL

5.CONFIGURATION METHODS

5.1. SMS Text Messages

In this document the underscore character ”_” represents one space character. Every underscore character must be re-

placed with a single space character. There must be no spaces or other unnecessary characters at the beginning and at the

end of the SMS text message.

SMS

In order to congure and control the system by SMS text message, send the text command to the ESIM120 system phone num-

ber from one of the listed administrator phone numbers. The structure of SMS text message consists of 4-digit SMS password

(the default SMS password is 0000 – four zeros), the parameter and value. For some parameters the value does not apply e. g.

STATUS. The variables are indicated in lower-case letters, while a valid parameter value range is indicated in brackets.

5.2. ELDES Conguration Tool Software

Cong

Tool

Software ELDES Conguration Tool is intended for ESIM120 GSM switch-gate controller conguration locally via USB port or

remotely via GPRS network connection. This software simplies system conguration process by allowing to use a personal

computer in the process. Before starting to use ELDES Conguration Tool software, please read the user guide provided in the

software’s HELP section.

ELDES Conguration Tool is freeware and can be downloaded from at: www.eldes.lt

NOTE: ELDES Conguration Tool software is secured with SMS password. The default SMS password is 0000 (see 7. SMS PASSWORD).

5.2.1.Remote Connection

ATTENTION: When ELDES Cloud Services feature is enabled (see 21. ELDES CLOUD SERVICES), remote connection via ELDES Cong-

uration Tool software becomes inaccessible. In such case you may use the remote conguration feature by accessing your ELDES Cloud

Services account via web-browser.

ELDES Conguration Tool software provides remote system conguration ability via Internet using one of the following methods:

• ELDES proxy server (recommended). The connection can be established on the system via GPRS network.

• Running TCP/IP server on ELDES Conguration Tool (advanced). The connection can be established on the system via GPRS network.

In order to start using the remote conguration feature, please run the step-by-step wizard and follow the steps provided in the start page

of ELDES Conguration Tool software. Please, note that it will be necessary to send an SMS text message to the system’s phone number

in order to initiate the remote connection. By following the steps you will be instructed on what text must be sent to the system’s phone

number in such case.

5.2.2. Ending the Remote Connection Session

After the system conguration is complete, use one of the following methods to end the conguration process:

• Click Disconnect or Stop button and close ELDES Conguration Tool software;

• The session will automatically expire in 20 minutes. Before the last 5 minutes, the software will oer the user to extend the session

for another 20 minutes.

• Alternatively, the connection with the server can be terminated at any time by sending an SMS text message.

Terminate the

connection

SMS text message content:

ssss_ENDCONFIG

Value: ssss – 4-digit SMS password.

Example: 1111_ENDCONFIG

Once the session is expired or terminated, the system will reply with an SMS text message conrming the end of the session.

Andere Handbücher für ESIM120

Inhaltsverzeichnis

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise