ElectrIQ ECOSILENT10W Bedienungsanleitung

USER MANUAL

electriQ PORTABLE AIR CONDITIONER

WITH WIFI

ECOSILENT8W

8,000 BTU

ECOSILENT8WE

ECOSILENT10W

10,000 BTU

ECOSILENT10WE

Thank you for choosing electriQ

Please read this user manual before using this innovative Air Conditioner and keep it

safe for future reference.

Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

CONTENTS

SAFETY

FEATURES AND PARTS LIST

INSTALLATION

OPERATION

REMOTE CONTROL

WIFI APP CONTROL

SETTING UP THE APP

CONNECTING THE AIR CONDITIONER

CONTROLLING YOUR DEVICE

SMART SCENES

CLEANING AND MAINTENANCE

EMPTYING THE INTERNAL WATER TANK

TROUBLESHOOTING

ERROR CODES

SUPPORT

TECHNICAL SPECIFICATION

SAFETY INSTRUCTIONS

Important!

•Carefully read the instructions before operating the unit

•This appliance is for indoor use only.

•Rating: This unit must be only connected to a 220-240 V / 50 Hz

earthed outlet.

•Installation must be in accordance with regulations of the country where the unit is

used.

•If you are in any doubt about the suitability of your electrical supply have it checked

and, if necessary, modified by a qualified electrician.

•This air conditioner has been tested and is safe to use. However, as with any electrical

appliance - use it with care.

•Disconnect the power from the appliance before dismantling, assembling or cleaning.

•Avoid touching any moving parts of the appliance.

•Never insert fingers, pencils or any other objects though the guard

•This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities. It is also not intended for use by those with a

lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their

safety.

•Do not leave children unsupervised with this appliance.

•Do not clean the unit by spraying it or immersing it in water.

•Never connect the unit to an electrical outlet using an extension cord. If an outlet is

not available, one should be installed by a qualified electrician.

•Never operate this appliance if the cord or plug is damaged. Ensure the power cord is

not stretched or exposed to sharp objects/edges.

•A damaged supply cord should be replaced by the manufacturer or a qualified

electrician in order to avoid a hazard.

•Any service other than regular cleaning or filter replacement should be performed by

an authorised service representative. Failure to comply could result in a voided

warranty.

•Do not use the appliance for any purpose other than its intended use.

•The air conditioner unit must always be stored and transported upright, otherwise

irreparable damage may be caused to the compressor; if in doubt we suggest waiting

at least 24 hours before starting the unit.

•Avoid restarting the air conditioning unit unless 3 minutes have passed since being

turned off. This prevents damage to the compressor.

•Never use the mains plug as a switch to start and turn off the air conditioning unit. Use

the provided ON/OFF button located on the control panel.

•Always place the unit on a dry and stable surface.

•The appliance should not be installed in laundry or wet rooms.

•The appliance must be placed in a room without sources of ignition (for example: open

flames, an operating gas appliance or an operating electric heater).

•R290 refrigerant gas complies with European environmental directives.

•R290 has a low GWP (Global Warming Potential) of 3.

•The ECOSILENT8W / 8WE contains about 220 g of R290 refrigerant gas.

•The ECOSILENT10W / 10WE contains about 280 g of R290 refrigerant gas.

•Do not use or store in an unventilated space with an area smaller than 10.6 m2per unit

(ECOSILENT8W / 8WE) or 13.4 m2per unit (ECOSILENT10W / 10WE).

•The room must be such as to prevent stagnation of possible leaks of refrigerant gas as

there could be a danger of fire or explosion should the refrigerant come into contact

with electric heaters, stoves or other sources of ignition.

•Refrigerant gas may be odourless.

•Do not use the product and contact the retailer for advice, if damage has occurred to

the unit which may have compromised the refrigerant system.

•Any repairs or maintenance must only be carried out on the unit by a suitably qualified

engineer. Before opening and servicing the unit the authorised engineer must be in

possession of a copy of the manufacturer’s service manual and must follow the safety

information contained within it to ensure all hazards are minimized.

•The refrigerant system should not be perforated or punctured.

Energy Saving and Unit Safety Protection Tips

•Do not cover or restrict the airflow from the outlet or inlet grills.

•For maximum performance the minimum distance from a wall or objects should be

50cm.

•Keep the filters clean. Under normal conditions, filters should only need cleaning once

every three weeks (approximately). Since the filters remove airborne particles, more

frequent cleaning maybe necessary, depending on the air quality.

•For the initial start-up set the fan speed to maximum and the thermostat to 5 degrees

lower than the current room temperature. After, set appliance to your desired

settings.

•To protect the unit, we recommend not using the cooling function when the ambient

temperature is higher than 35oC.

FEATURES AND PARTS LIST

FEATURES

•3 in 1 Cooling, Fan, Dehumidifier great for Rooms up to 20 sqm.

•5 speed DC fan: balancing quiet operation with performance.

•SmartCool Logic for Improved Energy Efficiency.

•24 Hours Start / Stop Timer

•Digital Thermostat.

•Smart WIFI App control

•Castors and Handles for Enhanced Portability.

•Auto-Restart to retain the settings in the event of power failure.

PART LIST

Top Cover

Control Panel

Louvres

Rear Housing

Front Cover

Castors

Upper Air Inlet

Lower Air Inlet

Exhaust Outlet

Carry Handle

Power Cable

Exhaust Hose

Window Slide Bar

INSTALLATION

WARNING: Before using this unit, please keep it upright for at least 3-4 hours.

This unit can easily be moved from one room to another.

While moving the unit please note that it must always be kept upright and then placed on an even surface.

1. Attach the fishtail connector to the end of the hose, by

extending the end and twisting until firmly attached (At least

3 full rotations).

2. Attach the connector on the opposite end of the pipe to the exhaust

outlet on the rear of the appliance by putting into position and twisting to

lock in place.

3. Make sure the unit is upright and there are no obstructions to

the air inlets and outlet grills.

INSTALLATION OF WINDOW KIT

The window kit (slide bar and fishtail) can be used

with sliding windows and doors. For other types of

window, the fishtail should be used on its own.

1. Partially open the window and place

the extended slide bar in position

before closing the window onto it.

2. Fix the fishtail adaptor into the

opening on the slide bar

3. Fix the exhaust connector on the

opposite end of the exhaust hose to

the exhaust outlet on the rear of the

air conditioner.

NOTES:

•The window kit is only designed to be installed with sliding or sash windows or doors. The window

kit is not designed to be used with any other style of windows.

•The fish tail adaptor can be used without the slide bar with most windows / doors.

•When using the air conditioner ensure that the opening around the fishtail adaptor is as small as

possible to ensure the efficiency of the unit is not reduced.

•The best form of installation is through a wall duct. By properly venting you expel hot air from your

room while efficiently cooling it.

•Your air conditioner should be used without the vent pipe in dry mode. When using dry mode

ensure that an external water tank is used, monitored and regularly emptied before overflowing.

Permanent plumbing can be also installed or an external uplift water pump can be set up to allow

for uninterrupted use.

IMPORTANT SAFEGUARDS

The length of the soft hose extends from approximately 30 cm to 180 cm. If hose is extended above this

length, the unit may malfunction which can invalidate the warranty. The outlet vent must be well

ventilated and not obstructed as this will cause the unit to overheat. Keep the hose as straight and short

as possible and avoid bending the air hose by more than 30 degrees in order not to reduce the

performance of the unit.

OPERATION

Press the POWER button to turn the unit ON or OFF.

Press the MODE button to cycle between the 4 modes, the indicator for the selected mode will

be illuminated.

COOL: The room is cooled with the cold air expelled through the front air outlet while hot air is

expelled through the vent pipe. The desired room temperature can be set between 17 and 30

degrees using the + and –buttons, and the fan speed can be changed using the SPEED button.

FAN: The fan speed can be changed pressing the SPEED button.

DRY (DEHUMIDIFY): Should be operated without the vent hose, but with continuous drainage

to remove moisture from the air. The display will show dH while in dry mode. The unit will

operate at low fan speed in DRY mode.

SMART COOL: An intelligent cooling mode where the fan speed is automatically adjusted based

on the amount of cooling required. Attempts to change the fan speed will move the unit into

COOL mode.

Repeatedly press the SPEED button to cycle through the five fan speeds. Each time the SPEED

button is pressed, the fan speed will be displayed. The fan speed can be changed between F1

(Low) to F5 (High). The LED indicators will also illuminate to show the fan speed as below:

F1 –Low, F2 –Low and Mid, F3 –Mid, F4 –Mid and High, F5 –High.

The fan speed cannot be changed in SMARTCOOL and DRY modes.

Press to enter sleep mode. The sleep indicator will be illumined and all other indicators will be

turned off. In sleep mode, the appliance works at low fan speed. Press SLEEP again to exit sleep

mode.

The SLEEP button is also used to set up the WIFI function. See the WIFI SMART CONTROL

section for further information.

The timer functions cannot be combined or repeated.

POWER ON TIMER

With the appliance in standby, press the TIMER button to set the power-on timer. Use the + and

- buttons to adjust the duration of the timer (1 to 24 hours). The Timer indicator will turn on

and the unit will start after the selected number of hours.

POWER OFF TIMER

With the appliance running with the desired settings, press the TIMER button to set the power-

off timer. Use the + and - buttons to adjust the duration of the timer (1 to 24 hours). The timer

indicator will illuminate and the unit will stop after selected number of hours.

Used to adjust the temperature in COOL/SMART COOL mode and to set the duration of the

TIMER. The buttons are not used in FAN or DRY modes. Press both buttons together to change

between displaying the temperature in Celsius and Fahrenheit.

Press this button to enable the swing function. The louvres will slowly move from side to side. If

swing is pressed again the louvres will stop in their current position.

Press and hold the swing button to turn off the status indicators on the control panel.

REMOTE CONTROL

NOTE: The design of the remote may vary from the diagram, due to

continuous product improvement.

MULTI PROTECTIVE FUNCTIONS

FROST PROTECTION

In COOL, DRY or SMART COOL modes, if the temperature of the exhaust is too low, the machine will

automatically stop operating until the temperature has risen.

OVERFLOW PROTECTION

When the water in the internal water tank exceeds the warning level, the machine will stop operating and

sound an alarm with the LCD display showing “E7”. To resume operation empty the internal water tank. After

the water is emptied, the machine will automatically return to the original state.

AUTO-DEFROST

The machine has automatic defrosting function. If during operation the temperature of the internal coils

drops too low, the unit will enter auto defrost and the heating symbol will flash on the control panel.

AUTOMATIC THERMAL PROTECTION

To protect the service life of the machine, the machine has automatic thermal protection. If the temperature

within the unit is outside of the specified range, the compressor and the lower motor will stop operation.

The appliance will automatically return to normal operation after the temperature of the machine recovers.

COMPRESSOR PROTECTION

To prevent damage to the compressor there is a 3 minute delay start protection function.

POWER

Press to turn the unit on or off.

TIMER

Press to set the timer.

DOWN

Press to decrease the desired temperature or

timer duration.

Press to increase the desired temperature or

timer duration.

SLEEP

Press the sleep button to enter sleep mode.

FAN

Press to enter fan / air purify mode.

COOL

Press to enter cool mode.

DRY

Press to enter dry (dehumidify) mode.

HIGH

Press to enter high (F5) speed fan.

LOW

Press to enter low (F1) speed fan.

WIFI SMART CONTROL

BEFORE YOU START

•Ensure your router provides a standard 2.4ghz connection.

•If your router is dual band ensure that both networks have different network names (SSID). The

provider of your router / Internet service provider will be able to provide advice specific to your

router.

•Place the air conditioner as close as possible to the router during setup.

•Once the app has been installed on your phone, turn off the data connection, and ensure your

phone is connected to your router via WIFI.

DOWNLOAD THE APP TO YOUR PHONE

Download the ”TUYA SMART” app, from your chosen app store, using the QR codes below, or by searching

for the app in your chosen store.

Android IOS

CONNECTION METHODS AVAILABLE FOR SETUP

The air conditioner has two different setup modes, EZ (Quick Connection) and AP (Access Point). The quick

connection is a quick and simple way to set the unit up. The AP connection uses a direct local wifi

connection between your phone and the air conditioner to upload the network details.

Before starting the setup, with the air conditioner plugged in, but turned off, press and hold the SLEEP

button for 5 seconds (until you hear a bleep) to enter the WIFI connection mode.

Please ensure your device is in the correct WIFI connection mode for the connection type you are

attempting, the flashing of the WIFI light on your air conditioner will indicate this.

Connection Type

Frequency of Flashes

EZ (Quick Connection)

Flashes twice per second

AP (Access Point)

Flashes once per second

CHANGING BETWEEN CONNECTION TYPES

To change the unit between the two WIFI connection modes, hold the SLEEP button for 5 seconds.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ElectrIQ Klimaanlage Handbücher

ElectrIQ

ElectrIQ P15HP Bedienungsanleitung

ElectrIQ

ElectrIQ SILENT 12 Bedienungsanleitung

ElectrIQ

ElectrIQ P12CE-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ SF8000E Bedienungsanleitung

ElectrIQ

ElectrIQ eIQ-9WMINV Betriebsanleitung

ElectrIQ

ElectrIQ COMPACT Bedienungsanleitung

ElectrIQ

ElectrIQ P12C Bedienungsanleitung

ElectrIQ

ElectrIQ SILENT12-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-FC18K Betriebsanleitung

ElectrIQ

ElectrIQ P12C-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ PLAC12000HP Bedienungsanleitung

ElectrIQ

ElectrIQ P18HP Bedienungsanleitung

ElectrIQ

ElectrIQ Compact V2 Bedienungsanleitung

ElectrIQ

ElectrIQ Arctic-Plus Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT12 Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-CRFC18K Handbuch

ElectrIQ

ElectrIQ SILENT10 Bedienungsanleitung

ElectrIQ

ElectrIQ iQool9PLUS Betriebsanleitung

ElectrIQ

ElectrIQ ECOSILENT8 Bedienungsanleitung

ElectrIQ

ElectrIQ AC100R Bedienungsanleitung

ElectrIQ

ElectrIQ AIRFLEX15-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ CMAC10M Bedienungsanleitung

ElectrIQ

ElectrIQ iQool9PLUS-V2 Betriebsanleitung

ElectrIQ

ElectrIQ P18HP Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung