ElectrIQ P16HP Bedienungsanleitung

Page 1 of 15

USER MANUAL

PORTABLE AIR CONDITIONER WITH HEATPUMP

P16HP / P18HP

Thank you for choosing electriQ

Please read this user manual before using this innovative Air Conditioner and

keep it safe for future reference.

Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

Page 2 of 15

CONTENTS

SAFETY INSTRUCTIONS

FEATURES AND PARTS LIST

INSTALLATION

OPERATION AND SETTINGS

WATER-DRAINAGE

MAINTENANCE

TROUBLESHOOTING

APPENDIX

Page 3 of 15

SAFETY INSTRUCTIONS

IMPORTANT!

Carefully read the instructions before operating the unit

This appliance is for indoor use only.

Rating: This unit must be only connected to a 220-240 V /

50 Hz earthed outlet.

Installation must be in accordance with regulations of the

country where the unit is used.

If you are in any doubt about the suitability of your electrical supply have it checked

and, if necessary, modified by a qualified electrician.

This air conditioner has been tested and is safe to use. However, as with any

electrical appliance - use it with care.

Disconnect the power plug from socket before dismantling, assembling or cleaning.

Avoid touching any moving parts within the appliance.

Never insert fingers, pencils or any other objects though the guard.

This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not be made by

children without supervision.

Do not leave children unsupervised with this appliance.

Do not clean the unit by spraying it or immersing it in water.

Never connect the unit to an electrical outlet using an extension cord. If an outlet

is not available, one should be installed by a qualified electrician.

Never operate this appliance if the cord or plug is damaged. Ensure the power

cord is not stretched or exposed to sharp objects/edges.

The power cord must not be immersed in water, as this could result in electric

shock.

A damaged supply cord should be replaced by the manufacturer or a qualified

electrician in order to avoid a hazard.

Any service other than regular cleaning or filter replacement should be performed

by an authorized service representative. Failure to comply could result in a voided

warranty.

When defrosting and cleaning the appliance, only use tools recommended by the

manufacturer.

Do not use the appliance for any purpose other than its intended use.

The air conditioner must always be stored and transported upright,

otherwise irreparable damage may be caused to the compressor; if in doubt

we suggest waiting at least 24 hours before starting the unit.

Avoid restarting the air conditioner unless 3 minutes have passed since being

turned off. This prevents damage to the compressor.

Never use the mains plug or an external timer as a switch to start and stop the air

conditioner. Use the provided ON/OFF button located on the control panel.

Always place the unit on a dry and stable surface.

The appliance should not be installed in laundry or wet rooms

Page 4 of 15

The appliance must be placed in a room without sources of ignition (for example:

open flames, an operating gas appliance or an operating electric heater).

R290 refrigerant gas complies with European environmental directives. R290 has

a low GWP (Global Warming Potential) of 3.

The P16HP contains about 225 g of R290 refrigerant gas, and the P18HP contains

about 300g of R290 refrigerant gas

Do not use or store in unventilated spaces with an area smaller than 10.8 m2 per

unit for P16HP and 14.4 m2 per unit for P18HP. The room must be such as to

prevent stagnation of possible leaks of refrigerant gas as there could be a danger

of fire or explosion hazard should the refrigerant come into contact with electric

heaters, stoves or other sources of ignition.

Do not use the product and contact the retailer for advice, if damage has occurred

to the unit which may have compromised the refrigerant system.

Refrigerant gas may be odourless.

Do not open the air conditioner, to attempt service or repair the unit. Any internal

servicing of the unit must be carried out only by the manufacturer or its authorized

technicians.

Any repairs or maintenance must only be carried out on the unit by a suitably

qualified engineer. Before opening and servicing the unit the authorized engineer

must be in possession of a copy of the manufacturer’s service manual and must

follow the safety information contained within it to ensure all hazards are minimized.

The refrigerant system should not be perforated or punctured.

ENERGY SAVING AND UNIT SAFETY PROTECTION TIPS

Do not cover or restrict the airflow from the outlet or inlet grills.

For maximum performance the air conditioner should be situated at least 50cm from the

walls or other objects.

Keep the filters clean. Under normal conditions, filters should only need cleaning once

every three weeks (approximately). Since the filters remove airborne particles, more

frequent cleaning maybe necessary, depending on the air quality.

For the initial start-up set the fan speed to maximum and the thermostat to 4-5 degrees

lower than the current temperature. After, set the fan to low and set the thermostat to your

desired setting.

To protect the unit we recommend the unit should only be used when the temperature of

the room is between 7°C and 35°C. If the temperature is below this use electrical

heating to raise the temperature above 10⁰C before starting the unit.

Page 5 of 15

FEATURES AND PARTS LIST

FEATURES

Full climate control, cooling, heating, fan and dehumidifier

Self-evaporative system - no external water tank needed

Powerful but compact

LED screen, indicates temperature and operation mode

Enhanced design with hot air outlet positioned higher – This allows for improved

performance with the use of a short hose

24 hour programmable timer function – Allows you to choose when the unit operates.

3 speed fan Low, Medium and High for best balance between quiet operation and

maximum airflow

Compressor protection technology

Page 6 of 15

PARTS LIST

ACCESSORIES

Rear cover

SIDE VIEW

Castor

FRONT VIEW

Control Panel

REAR VIEW

Plug

Air

Inlet

Exhaust Hose

Fishtail Connector

Slide Bar

Remote Control

Exhaust hose connector

Page 7 of 15

INSTALLATION

Warning：Before using this unit, please keep it upright for at least 3-4 hours.

This unit can easily be moved from one room to another.

While moving the unit please note that it must always be kept upright and then placed on

an even surface.

1. Assemble the fishtail adaptor on to the hose, by extending the end of the hose and

twisting the fishtail into position (At least 3 full rotations)

2. Assemble the Exhaust hose connector on to the other end of the hose, by extending the

opposite end of the hose and twisting the outlet into position (At least 3 full rotations)

3. Attach the Exhaust hose connector to the

rear of the air conditioner

4. Make sure the unit is upright and there are no

obstructions to the air inlets and outlet grills. A minimum

of 50cm clearance should be left between the inlet/outlet

grills and any obstruction.

Page 8 of 15

INSTALLATION OF WINDOW KIT

1. Partially open the window and then fix the slide bar into the opening in the window, by

putting it into position before closing the window onto it to seal the gap.

2. Push the fishtail adaptor into the slot in the slide bar

Note: The slide bar is only designed to be installed with sliding or sash windows or doors.

The slidebar is not designed or to be used with any other style of window. However

the fish tail adaptor can be used with most windows /doors. When using cooling or

heating modes ensure that the opening is left as small as possible.

The best form of installation is through a wall duct. By properly venting you expel

hot air from your room while efficiently cooling it.

IMPORTANT SAFEGUARDS

The length of the soft hose extends from 28 cm to 150 cm. If hose

is extended above this length the unit may malfunction and this

can invalidate the warranty.

The outlet vent must be well ventilated and not obstructed as this

will cause the unit to overheat.

Avoid bending the air hose more than 30 degrees.

Page 9 of 15

OPERATION AND SETTINGS

CONTROL PANEL & FUNCTION

POWER BUTTON

Press to turn unit “ON” or “OFF”

MODE

Pressing this button will select between the Cooling , Heating , Auto, Fan and

Dehumidify modes.

COOLING MODE: Cold air will be expelled through the top of the unit and hot air will

be expelled through the vent hose.

HEATING MODE: Hot air will be expelled through the top of the unit and cold air will be

expelled through the vent hose. Continuous drainage should be set up for the moisture

collected.

DEHUMIDIFY MODE: The unit should be set up without a vent hose, moisture is

extracted from the air that passes through the unit. Continuous drainage should be set

up for the moisture collected.

FAN MODE: No cooling effect, circulates air within the room, vent pipe not required.

AUTO MODE: The unit will change between Heating, cooling and fan modes depending

on the desired temperature set.

TEMPERATURE UP & DOWN

During cooling and heating modes – These buttons raise or lower the temperature by 1oC

for each press. The minimum temperature is 16oC and max. 31oC.

FAN SPEED

Press to select either LOW, MEDIUM or HIGH fan speed.

NOTE: In dehumidifying mode, this button is invalid as the unit is designed to run at low

speed in dehumidifying mode.

Page 10 of 15

SLEEP MODE

Press the SLEEP button to enter sleep mode, the default fan speed is low and the Sleep

mode indicator led will illuminate.

When the sleep mode is turned on:

After one hour the set temperature will increase by 1 degree Celsius, after another hour

the set temperature will increase by another degree, and will then remain set at that

temperature.

Please note:

Sleep mode cannot be used in dry and fan modes.

If internal tank becomes full, the machine will turn off and sleep mode will be

cancelled.

SWING BUTTON

After machine is on and mode selected, press this button and the louver will swing

continuously up and down; by pressing this button again the movement will stop and the

louver remain fixed in position.

TIMER BUTTON

The in-built timer will allow you to set the unit to turn on or turn off after a set period of

time, Please note only one timer can be used at any time.

ON TIMER – The timer will turn on the unit automatically after the time set has elapsed.

1. With the unit turned off, press the TIMER button, then set the number of hours’ time

you desire the unit to start by using the UP and DOWN buttons.

2. Once the set time has elapsed, the unit will turn on automatically.

3. Press the POWER button before the time has elapsed and the unit will turn on as

normal and the timer will be cancelled

4. The function and fan speed can be set whilst setting the timer.

OFF TIMER – The timer will turn off the unit automatically after the time set has elapsed.

1. While the unit is operating, press the TIMER button then set the number of hours’

time you desire the unit to stop by using the UP and DOWN buttons.

2. Once the set time has elapsed, the unit will turn off automatically.

3. Press the POWER button before the time has elapsed, the setting time will be

cancelled and the unit will turn off.

TANK FULL INDICATOR

When the internal water tank is full, the unit will stop operation, and the TANK FULL

indicator will illuminate. To restart operation, empty the water tank following the

information in the Water drainage section

LED DISPLAY

The display indicates the current target temperature or the remaining timer settings. When

the set temperature or the timer is adjusted, the new setting is shown.

The display is also used to show error codes. Should a fault occur, see ERROR CODES.

Andere Handbücher für P16HP

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ElectrIQ Klimaanlage Handbücher

ElectrIQ

ElectrIQ ECOSILENT10W Bedienungsanleitung

ElectrIQ

ElectrIQ PLM12000HP Bedienungsanleitung

ElectrIQ

ElectrIQ iQool-2MS9K9K Betriebsanleitung

ElectrIQ

ElectrIQ SILENT 12 Bedienungsanleitung

ElectrIQ

ElectrIQ AIRFLEX15 Bedienungsanleitung

ElectrIQ

ElectrIQ Compact V2 Bedienungsanleitung

ElectrIQ

ElectrIQ Platinum Series Bedienungsanleitung

ElectrIQ

ElectrIQ SF12000 Bedienungsanleitung

ElectrIQ

ElectrIQ AIRFLEX 15 Bedienungsanleitung

ElectrIQ

ElectrIQ SILENT10 Bedienungsanleitung

ElectrIQ

ElectrIQ iQool9PLUS Betriebsanleitung

ElectrIQ

ElectrIQ AIRCUBE Bedienungsanleitung

ElectrIQ

ElectrIQ iQool-3MS9K9K9K Betriebsanleitung

ElectrIQ

ElectrIQ eiQ-9WMINV-V3 Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT12HPW-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-9WMINV-V2 Betriebsanleitung

ElectrIQ

ElectrIQ eIQ-9WMINV Betriebsanleitung

ElectrIQ

ElectrIQ AIRFLEX 15 Bedienungsanleitung

ElectrIQ

ElectrIQ CMAC10M Bedienungsanleitung

ElectrIQ

ElectrIQ IQOOL-SMART12HP Bedienungsanleitung

ElectrIQ

ElectrIQ IQOOL-SMART15HP Bedienungsanleitung

ElectrIQ

ElectrIQ P18HP Bedienungsanleitung

ElectrIQ

ElectrIQ iQool9 Bedienungsanleitung

ElectrIQ

ElectrIQ P18HP Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung