ElectrIQ P12C-V2 Bedienungsanleitung

USER MANUAL

12,000 BTU PORTABLE AIR CONDITIONER

P12C-V2

Thank you for choosing electriQ

Please read this user manual before using this innovative Air Conditioner and

keep it safe for future reference.

Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

Page 2 of 15

CONTENTS

SAFETY INSTRUCTIONS

FEATURES

DIAGRAM AND ACCESSORIES

INSTALLATION

OPERATION

REMOTE CONTROL

WATER-DRAINAGE

MAINTENANCE

TROUBLESHOOTING

TECHNICAL DATA

SUPPORT

Page 3 of 15

SAFETY INSTRUCTIONS

Important!

Carefully read the instructions before operating the unit

This appliance is for indoor use only.

Rating: This unit must be only connected to a 220-240 V

/ 50 Hz earthed outlet.

Installation must be in accordance with regulations of the

country where the unit is used.

If you are in any doubt about the suitability of your electrical supply have it

checked and, if necessary, modified by a qualified electrician.

This air conditioner has been tested and is safe to use. However, as with any

electrical appliance - use it with care.

Disconnect the power plug from socket before dismantling, assembling or

cleaning.

Avoid touching any moving parts within the appliance.

Never insert fingers, pencils or any other objects though the guard

This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

Do not leave children unsupervised with this appliance.

Do not clean the unit by spraying it or immersing it in water.

Never connect the unit to an electrical outlet using an extension cord. If an outlet

is not available, one should be installed by a qualified electrician.

Never operate this appliance if the cord or plug is damaged. Ensure the power

cord is not stretched or exposed to sharp objects/edges.

The power cord must not be immersed in water, as this could result in electric

shock.

A damaged supply cord should be replaced by the manufacturer or a qualified

electrician in order to avoid a hazard.

Any service other than regular cleaning or filter replacement should be

performed by an authorized service representative. Failure to comply could

result in a voided warranty.

When defrosting and cleaning the appliance, only use tools recommended by

the manufacturer.

Do not use the appliance for any other purpose than its intended use.

The air conditioner unit must always be stored and transported upright,

otherwise irreparable damage may be caused to the compressor; if in

doubt we suggest waiting at least 24 hours before starting the unit.

Avoid restarting the air conditioning unit unless 3 minutes have passed since

being turned off. This prevents damage to the compressor.

Page 4 of 15

Never use the mains plug or an external timer as a

switch to start and stop the air conditioning unit. Use

the provided ON/OFF button located on the control

panel.

Always place the unit on a dry and stable surface.

The appliance should not be installed in laundry or wet

rooms

The appliance must be placed in a room without

sources of ignition (for example: open flames, an

operating gas appliance or an operating electric heater).

R290 refrigerant gas complies with European

environmental directives.

R290 has a low GWP (Global Warming Potential) of 3.

The air conditioner contains about 215 g of R290 refrigerant gas.

Do not use or store in an unventilated space with an area smaller than 10.3m2 per

unit. The room must be such as to prevent stagnation of possible leaks of

refrigerant gas as there could be a danger of fire or explosion hazard should the

refrigerant come into contact with electric heaters, stoves or other sources of

ignition.

If the appliance is installed, used or stored in an unventilated room, the room must

be such as to prevent stagnation of possible leaks of refrigerant gas as there could

be a danger of fire or explosion should the refrigerant come into contact with

electric heaters, stoves or other sources of ignition.

Refrigerant gas may be odourless.

Do not use the product and contact the retailer for advice, if damage has occurred

to the unit which may have compromised the refrigerant system.

Any repairs or maintenance must only be carried out on the unit by a suitably

qualified engineer. Before opening and servicing the unit the authorized

engineer must be in possession of a copy of the manufacturer’s service manual

and must follow the safety information contained within it to ensure all hazards are

minimized.

The refrigerant system should not be perforated or punctured.

Energy Saving and Unit Safety Protection Tips

Do not cover or restrict the airflow from the outlet or inlet grills.

For maximum performance the air conditioner should be situated at least 50cm

from the walls or other objects.

Keep the filters clean. Under normal conditions, filters should only need

cleaning once every three weeks (approximately). Since the filters remove

airborne particles, more frequent cleaning maybe necessary, depending on the

air quality.

For the initial start-up set the fan speed to maximum and the thermostat to 4-5

degrees lower than the current temperature. After, set the fan switch to low and

set the thermostat to your desired setting.

To protect the unit we recommend the unit should only be used when the room

temperature is between 7°C and 35°C. If the temperature is below this use

electrical heating to raise the temperature above 10⁰C before starting the unit.

Page 5of 15

FEATURES

Self-evaporative system - no external water tank needed

Powerful but compact

Hidden display on front of the unit

Enhanced design with hot air outlet positioned higher – this allows for improved

performance with the use of a short hose

24 hour programmable timer function – allows you to choose when the unit operates.

2 speed fan, Low and High for best balance

between quiet operation and

maximum airflow

Compressor protection technology

Page 6 of 15

DIAGRAM

ACCESSORIES

Control Panel

TOP VIEW

LEFT VIEW

FRONT VIEW

RIGHT VIEW

BACK VIEW

Display Panel

Air Inlet

Power cable

Handle

Air Inlet

Upper

drainage

port

Lower

Drainage

port

Slide bar

Fishtail adaptor

Exhaust hose

FRONT VIEW

Remote control

FRONT VIEW

Exhaust hose connector

FRONT VIEW

Page 7 of 15

INSTALLATION

Warning：Before using this unit, please keep it upright for at least 3-4 hours.

This unit can easily be moved from one room to another.

While moving the unit please note that it must always be kept upright and then placed

on an even surface.

1. Assemble the fishtail adaptor on to the hose, by extending the end of the hose and

twisting the fishtail into position (At least 3 full rotations)

2. Assemble the Exhaust hose connector on to the other end of the hose, by extending the

opposite end of the hose and twisting the outlet into position (At least 3 full rotations)

3. Attach the exhaust hose connector onto to the exhaust outlet on

the rear of the air conditioner body, by pushing into position.

4. Make sure the unit is upright and there are no obstructions to

the air inlets and outlet grills. A minimum of 50cm clearance

should be left between the inlet/outlet grills and any

obstruction.

Page 8 of 15

INSTALLATION OF WINDOW KIT

1. Partially open the window and then fix the slide bare into the opening in the window, by

putting it into position before closing the window onto it to seal the gap.

2. Push the fishtail adaptor into the slot in the slide bar

Note: The slide bar is only designed to be installed with sliding or sash windows or doors.

The slidebar is not designed or to be used with any other style of window. However

the fish tail adaptor can be used with most windows / doors. When using the

cooling mode ensure that the opening is left as small as possible.

The best form of installation is through a wall duct.

By properly venting you expel hot air from your room while efficiently cooling it.

Important safeguards

The length of the soft hose extends from 28 cm to 150 cm. If hose is

extended above this length the unit may malfunction and this can

invalidate the warranty.

The outlet vent must be well ventilated and not obstructed as this will

cause the unit to overheat.

Avoid bending the air hose more than 30 degrees.

Page 9 of 15

OPERATION AND SETTINGS

CONTROL PANEL & FUNCTION

POWER BUTTON

Press to turn unit “ON” or “OFF”

MODE BUTTON

Pressing this button will select between the COOL, DRY (dehumidify) and FAN modes.

The lights next to the button indicate the currently running mode.

COOL MODE: Cold air will be expelled through the front of the unit and hot air will be expelled

through the vent hose.

DRY (DEHUMIDIFIER) MODE: The unit should be set up without a vent hose, moisture is

extracted from the air that passes through the unit. Continuous drainage should be set up for

the moisture collected (Drainage pipe not included).

FAN MODE: No cooling effect, circulates air within the room, vent pipe not required.

UP & DOWN BUTTONS

During cooling function – These buttons raise or lower the temperature by 1oC for each

press. The minimum temperature is 16oC and max. 31oC.

SPEED BUTTON

Press to select either LOW or HIGH fan speed. The lights next to the button will indicate

the fan speed currently selected.

NOTE: In dehumidifying function, this button is invalid as the unit is designed to run at low

speed in dehumidifying mode.

Page 10 of 15

SLEEP MODE

Press the Sleep button to enter sleep mode, the default fan speed is low and the Sleep

mode indicator led will illuminate.

When the sleep mode is turned on:

After one hour the set temperature will increase by 1 degree Celsius, after another hour

the set temperature will increase by another degree, and will then remain set at that

temperature.

Please note:

Sleep mode cannot be used in dry and fan modes.

If internal tank becomes full, the machine will turn off and sleep mode will be

cancelled.

TIMER BUTTON

The in-built timer will allow you to set the unit to turn on or turn off after a set period of

time, Please note only one timer can be used at any time.

ON TIMER – The timer will turn on the unit automatically after the time set has elapsed.

1. With the unit turned off, press the TIMER button, then set the number of hours’ time

you desire the unit to start by using the UP and DOWN buttons.

2. Once the set time has elapsed, the unit will turn on automatically.

3. Press the POWER button before the time has elapsed and the unit will turn on as

normal and the timer will be cancelled

4. The function and fan speed can be set whilst setting the timer.

OFF TIMER – The timer will turn off the unit automatically after the time set has elapsed.

1. While the unit is operating, press the TIMER button then set the number of hours’

time you desire the unit to stop by using the UP and DOWN buttons.

2. Once the set time has elapsed, the unit will turn off automatically.

3. Press the POWER button before the time has elapsed, the setting time will be

cancelled and the unit will turn off.

TANK FULL INDICATOR

When illuminated this indicates that the internal water tank is full and requires emptying,

following the information provided in the water drainage section.

LED DISPLAY

The display indicates the current target temperature or the remaining timer settings. When

the set temperature or the timer is adjusted, the new setting is shown.

The display is also used to show error codes. Should a fault occur, see ERROR CODES.

CHANGE BETWEEN FARENHEIT AND CELCIUS

To change the unit of measurement shown on the display, press both the UP and DOWN

buttons at the same time

Inhaltsverzeichnis

Andere ElectrIQ Klimaanlage Handbücher

ElectrIQ

ElectrIQ ECOSILENT12HPW Bedienungsanleitung

ElectrIQ

ElectrIQ SF8000E Bedienungsanleitung

ElectrIQ

ElectrIQ P15C Bedienungsanleitung

ElectrIQ

ElectrIQ CMAC12M Bedienungsanleitung

ElectrIQ

ElectrIQ PLAC12000HP Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT10W Bedienungsanleitung

ElectrIQ

ElectrIQ IQOOL-SMART12HP Bedienungsanleitung

ElectrIQ

ElectrIQ COMPACT Bedienungsanleitung

ElectrIQ

ElectrIQ SILENT16-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-CRFC18K Handbuch

ElectrIQ

ElectrIQ P12HPWR Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT8-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ SILENT12-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ AIRFLEX15-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ P12CE-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-12K12KC24KWMINV Betriebsanleitung

ElectrIQ

ElectrIQ iQool-2MS9K9K Betriebsanleitung

ElectrIQ

ElectrIQ PLM12000HP Bedienungsanleitung

ElectrIQ

ElectrIQ AIRFLEX 15 Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-9WMINV-V3 Bedienungsanleitung

ElectrIQ

ElectrIQ P18HP Bedienungsanleitung

ElectrIQ

ElectrIQ AIRFLEX 15 Bedienungsanleitung

ElectrIQ

ElectrIQ P15HP Bedienungsanleitung

ElectrIQ

ElectrIQ SILENT10 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung