ElectrIQ SILENT10 Bedienungsanleitung

USER MANUAL

SILENT10

PORTABLE AIR CONDITIONER

Thank you for choosing electriQ

Please read this user manual before using this innovative Air Conditioner and keep it

safe for future reference.

Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

Page 2 of 14 
CONTENTS
SAFETY INSTRUCTIONS......................................................... 3
FEATURES ............................................................................... 5
PARTS LIST.............................................................................. 5
INSTALLATION ........................................................................ 6
OPERATION ............................................................................. 8
REMOTE CONTROL................................................................. 9
EMPTYING THE INTERNAL WATER TANK.......................... 10
MANUAL DRAINAGE:............................................................ 10
MAINTENANCE...................................................................... 11
CLEANING.............................................................................. 11
END OF SEASON MAINTENANCE........................................ 11
TROUBLESHOOTING............................................................ 12
APPENDIX .............................................................................. 13
TECHNICAL DATA................................................................. 13
 
 

Page 3 of 14

SAFETY INSTRUCTIONS

Important!

•Carefully read the instructions before operating the unit

•This appliance is for indoor use only.

•Rating: This unit must be only connected to a 220-240 V /

50 Hz earthed outlet.

•Installation must be in accordance with regulations of the country where the

unit is used.

•If you are in any doubt about the suitability of your electrical supply have it

checked and, if necessary, modified by a qualified electrician.

•This air conditioner has been tested and is safe to use. However, as with any

electrical appliance - use it with care.

•Disconnect the power from the appliance before dismantling, assembling or

cleaning.

•Avoid touching any moving parts of the appliance.

•Never insert fingers, pencils or any other objects though the guard

•This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities. It is also not intended for

use by those with a lack of experience and knowledge, unless they have

been given supervision or instruction concerning the use of the appliance by

a person responsible for their safety.

•Do not leave children unsupervised with this appliance.

•Do not clean the unit by spraying it or immersing it in water.

•Never connect the unit to an electrical outlet using an extension cord. If an

outlet is not available, one should be installed by a qualified electrician.

•Never operate this appliance if the cord or plug is damaged. Ensure the

power cord is not stretched or exposed to sharp objects/edges.

•A damaged supply cord should be replaced by the manufacturer or a

qualified electrician in order to avoid a hazard.

•Any service other than regular cleaning or filter replacement should be

performed by an authorised service representative. Failure to comply could

result in a voided warranty.

•Do not use the appliance for any purpose other than its intended use.

•The air conditioner unit must always be stored and transported upright,

otherwise irreparable damage may be caused to the compressor; if in

doubt we suggest waiting at least 24 hours before starting the unit.

•Avoid restarting the air conditioning unit unless 3 minutes have passed since

being turned off. This prevents damage to the compressor.

•Never use the mains plug as a switch to start and turn off the air conditioning

unit. Use the provided ON/OFF button located on the control panel.

•Always place the unit on a dry and stable surface.

•The appliance should not be installed in laundry or wet rooms.

Page 4 of 14

•The appliance must be placed in a room without sources of ignition (for

example:open flames, an operating gas appliance or an operating electric

heater).

•R290 refrigerant gas complies with European

environmental directives.

•R290 has a low GWP (Global Warming

Potential) of 3.

•The air conditioner contains about 210 g of

R290 refrigerant gas.

•Do not use or store in an unventilated space

with an area smaller than 11m2per unit.

•The room must be such as to prevent

stagnation of possible leaks of refrigerant gas

as there could be a danger of fire or explosion

hazard should the refrigerant come into contact

with electric heaters, stoves or other sources of

ignition.

•Refrigerant gas may be odourless.

•Do not use the product and contact the retailer for advice, if damage has

occurred to the unit which may have compromised the refrigerant system.

•Any repairs or maintenance must only be carried out on the unit by a suitably

qualified engineer. Before opening and servicing the unit the authorized

engineer must be in possession of a copy of the manufacturer’s service

manual and must follow the safety information contained within it to ensure

all hazards are minimized.

•The refrigerant system should not be perforated or punctured.

Energy Saving and Unit Safety Protection Tips

•Do not cover or restrict the airflow from the outlet or inlet grills.

•For maximum performance the minimum distance from a wall or objects

should be 50cm.

•Keep the filters clean. Under normal conditions, filters should only need

cleaning once every three weeks (approximately). Since the filters remove

airborne particles, more frequent cleaning maybe necessary, depending on

the air quality.

•For the initial start up set the fan speed to maximum and the thermostat to 5

degrees lower than the current temperature. After, set the fan switch to low

and set the thermostat to your desired setting.

•To protect the unit we recommend not using the cooling function when the

ambient temperature is higher than 35oC.

Page 5 of 14

FEATURES

⚫Self-evaporative system - no external water tank needed

⚫Designer inspired luxury model

⚫Bright LED screen, indicates temperature and operation mode

⚫On/Off timer function –allows you to choose when the unit operates

⚫Compressor protection technology

PARTS LIST

ACCESSORIES:

1：Extendable Slide Bar 2: Fishtail Adaptor 3: Extendable Exhaust Hose

4: Exhaust Connector 5: Remote Control

Page 6 of 14

INSTALLATION

Warning: Before using this unit, please keep it upright for at least 3-4 hours.

This unit can easily be moved from one room to another.

While moving the unit please note that it must always be kept upright and then placed on an

even surface.

1. Attach the fishtail connector to the end of the hose, by

extending the end of the hose and twisting the fishtail

adaptor until it is firmly attached (At least 3 full rotations)

2. Extend the opposite end of the hose and screw into the

exhaust connector (At least 3 full turns)

3. Push the Exhaust Connector onto the Exhaust outlet on the

rear of the unit

4. Make sure the unit is upright and there are no obstructions to the

air inlets and outlet grills.

INSTALLATION OF WINDOW KIT.

The window kit (slide bar and fishtail) can be used with sliding windows and doors. For other types of

window, the fishtail should be used on its own.

1. Partially open the window and then fix the

window kit to the window.

2. Fix the fishtail adaptor into the

opening on the slide bar

3. Fix the exhaust connector on the

opposite end of the exhaust hose to

the exhaust outlet on the rear of the

air conditioner.

Page 7 of 14

NOTES:

•The window kit is only designed to be installed with sliding or sash windows or doors. The window

kit is not designed or to be used with any other style of windows.

•The fish tail adaptor can be used without the slide bar with most windows / doors.

•When using the air conditioner ensure that the opening left around the fishtail is as small as

possible as the cooling will be less efficient.

•The best form of installation is through a wall duct. By properly venting you expel hot air from your

room while efficiently cooling it.

•Your air conditioner should be used without the vent pipe in dry mode. When using dry mode

ensure that an external water tank is used, monitored and regularly emptied before overflowing.

Permanent plumbing can be also installed for dry mode or an external uplift water pump can be set

up for unattended use.

IMPORTANT SAFEGUARDS

The length of the soft hose extends from approximately 28 cm to

150 cm. If hose is extended above this length, the unit may

malfunction and this can invalidate the warranty. The outlet vent

must be well ventilated and not obstructed as this will cause the unit

to overheat. Avoid bending the air hose more than 30 degrees.

Page 8 of 14

OPERATION

When first plugged in the unit will automatically enter standby mode.

ON/OFF button: Press to turn the unit on and enter cooling mode. The unit will default to cooling mode

with a desired temperature of 22⁰C. Press again and the unit will switch off.

MODE BUTTON : Press this button to change between Cooling, Fan and Dry Modes.

FAN BUTTON

FAN AND COOL MODE: Press to change between the available fan speeds.

DRY MODE: The fan is set to low speed and cannot be changed

TIMER : The timer functions cannot be combined or repeated.

POWER ON TIMER

With the appliance in standby, press the “TIMER” button to setup the power-on time.

Press the UP and DOWN buttons to adjust the duration of the timer (from 1 to 24 hours). Timer

indicator turns on. The unit will start after selected number of hours.

POWER OFF TIMER

With the appliance running with the desired settings, press the “TIMER” button to setup the

power-off timer. Press the UP and DOWN buttons to adjust the duration of the timer (from 1 to 24

hours). The timer indicator will illuminate. The unit will stop after selected number of hours.

UP AND DOWN BUTTONS: Press to adjust the desired temperature and timer. In cooling mode,

the temperature can range from 16 - 31⁰C.

Press the UP and DOWN buttons together to change between ⁰C and ℉.

SLEEP MODE BUTTON :

While in cool mode press the “SLEEP” button to put the unit in sleep mode. The fan speed will change to

low. It will automatically increase the desired room temperature by 1℃after an hour and by a further 1℃

after a further hour. This means the unit will spend less time with the compressor running, and so run

quieter.

The sleep function cannot be used in dry and fan modes.

If the water tank is filled, the unit is put into standby or the mode is changed, sleep mode will be

cancelled.

Page 9 of 14

REMOTE CONTROL

The air conditioner can be controlled with the remote control. Two AAA-batteries are required to use the

remote control.

1. POWER : Press the POWER button to turn the machine on or off.

2. TIMER : Press the TIMER button to set the timer.

3. DOWN : Press the DOWN button to decrease the desired temperature or

timer

4. MODE : Press the MODE button to switch between cooling, fan and dry

modes.

5. UP :Press the UP button to increase the desired temperature or timer

6. FAN : Press the FAN button to change between high and low fan speeds.

7. SLEEP MODE : Press the SLEEP button to turn on the sleep mode

MULTI PROTECTIVE FUNCTIONS

ANTI-FREEZING PROTECTING CONTROL

When the ambient temperature is low while in Cooling Mode, the compressor and water motor will stop

working. If the copper coil temperature reaches < 2⁰C for over 20 seconds. When the copper coil

temperature increases to >8⁰C, the protection will be stopped.

WATER-FULL PROTECTION:

When the water level in the internal water tank reaches the maximum level, the unit will sound an alarm

and the tank full light will illuminate. Please drain the water from the internal water tank by removing the

rubber stopper.

COMPRESSOR DELAY-PROTECTION

The compressor runs a 3 minute delay protection function.

COMPRESSOR PROTECTION

In cooling and dry modes, if the temperature difference between the coil temperature and room

temperature is less than 3⁰C, for more than 30 minutes, the machine will enter the ‘no refrigerant’

compressor protection mode. The compressor and water spring motor will stop working. The up

fan runs at low speed and the down fan stops running

Page 10 of 14

EMPTYING THE INTERNAL WATER TANK

MANUAL DRAINAGE:

When the internal water tank is full the unit will stop working and the

tank full light will illuminate. Turn off the unit and unplug. Try not to

move the unit abruptly as this may cause the water in the internal tank

to spill out. Place a tray under the rubber stopper or place the unit in

a drainage area.

Remove the rubber stopper –water will drain from the internal tank.

Put the rubber stopper back into place.

CONTINUOUS DRAINAGE:

Remove the rubber stopper from the continuous drainage port

Connect a water pipe to the water outlet. You can plumb this pipe into your current plumbing

system, lead it outside and use gravity fall or use a water pump.

Note: This model has a self-evaporative function, which reduces the need to empty the water tank. If

the unit is vented correctly most of the water is reused to cool the condenser coils and any excess is

evaporated. Please do not use continuous drainage if you intend to use the self-evaporating facility.

Andere Handbücher für SILENT10

Inhaltsverzeichnis

Andere ElectrIQ Klimaanlage Handbücher

ElectrIQ

ElectrIQ SF12000 Bedienungsanleitung

ElectrIQ

ElectrIQ iQool9PLUS Betriebsanleitung

ElectrIQ

ElectrIQ COMPACT Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-CRFC18K Handbuch

ElectrIQ

ElectrIQ ECOSILENT12 Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT12HPW-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-9K9KC18KWMINV Betriebsanleitung

ElectrIQ

ElectrIQ P12HPW Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT12HPWE Bedienungsanleitung

ElectrIQ

ElectrIQ AIRCUBE Bedienungsanleitung

ElectrIQ

ElectrIQ Arctic-Plus Bedienungsanleitung

ElectrIQ

ElectrIQ Compact V2 Bedienungsanleitung

ElectrIQ

ElectrIQ P15HP Bedienungsanleitung

ElectrIQ

ElectrIQ AIRFLEX15-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ P12HPW Bedienungsanleitung

ElectrIQ

ElectrIQ eiQ-9WMINV-V3 Bedienungsanleitung

ElectrIQ

ElectrIQ AC100R Bedienungsanleitung

ElectrIQ

ElectrIQ P12HPW-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ SILENT16 Bedienungsanleitung

ElectrIQ

ElectrIQ SILENT16-V2 Bedienungsanleitung

ElectrIQ

ElectrIQ ECOSILENT8 Bedienungsanleitung

ElectrIQ

ElectrIQ iQool-2MS9K9K Betriebsanleitung

ElectrIQ

ElectrIQ CMAC10M Bedienungsanleitung

ElectrIQ

ElectrIQ eIQ-9WMINV Betriebsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung