Electro-Voice RE3-BP0L-T Bedienungsanleitung

RE3 UHF Wireless

en Installation manual

2 en | Table of contents RE3 UHF

Wireless

21.06 | 3 | F.01U.362.808 Installation manual Electro-

Voice

RE3

UHF Wireless Table of contents | en 3

Electro

-Voice Installation manual 2021.06 | 03 | F.01U.362.808

Table of contents

Table of contents 3

1Safety, precautions, and notices 4

1.1 Important safety instructions 4

1.2 Battery precautions 5

1.3 Notices 5

1.4 Licensing, certifications, restrictions and manufacturers declarations 6

2Short information 10

2.1 Shipping contents 11

3Description 13

4Glossary of terms 15

5Best practices for successful operation 17

6Quick setup 19

6.1 Preparing the receiver 19

6.2 Preparing the transmitter 19

6.3 Sync the transmitter to the receiver 19

6.4 Ensure transmitter input sensitivity is set for best signal level 20

7RE3-RX receiver 21

7.1 Product identification 21

7.2 LCD display 24

7.3 RE3-RX setup menu 25

8RE3-HHT handheld transmitter 40

8.1 Product identification 40

8.2LCD display 42

8.3 Installing batteries 43

8.4 RE3-HHT setup menu 43

9RE3-BPT bodypack transmitter 47

9.1 Product identification 47

9.2 LCD display 49

9.3 Installing batteries 50

9.4 RE3-BPT Setup Menu 50

10 Accessories for RE3 54

11 Troubleshooting and FAQ 56

11.1 Troubleshooting 56

11.2 Frequently Asked Questions 62

12 Technical data 67

13 Frequency Group / Channel Tables 77

4 en | Safety, precautions, and notices RE3 UHF

Wireless

21.06 | 3 | F.01U.362.808 Installation manual Electro-

Voice

1Safety, precautions, and notices

1.1 Important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug where present.

A polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade or the third prong is

provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

WARNING:TO REDUCE THE RISK OF

FIRE OR ELECTRIC SHOCK, DO NOT

OVEREXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE

AVIS: RISQUE DE CHOC ELECTRIQUE, NE

PAS OUVRIR.

WARNING:THE MAINS PLUG OR DC

INLET IS USED AS A DISCONNECT

DEVICE. THE DISCONNECT DEVICE SHALL

REMAIN READILY OPERABLE.

WARNING: CONNECT ONLY TO MAINS

SOCKET WITH PROTECTIVE EARTHING

CONNECTION.

WARNING:TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK) AS THERE ARE NO

USER-SERVICABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED PERSONNEL.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and

maintenance (servicing)

instructions in the literature

accompanying the appliance.

RE3

UHF Wireless Safety, precautions, and notices | en 5

Electro

-Voice Installation manual 2021.06 | 03 | F.01U.362.808

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug the apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

14. No naked flame sources, such as lighted candles, should be placed on the apparatus.

15. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or

moisture. The apparatus should not be exposed to dripping or splashing. Objects filled

with liquids, such as vases or open beverage containers should not be placed on

apparatus.

16. To completely disconnect DC power from this apparatus, the DC power supply cord

must be unplugged from the apparatus, or the apparatus’ external power supply must

be unplugged from the AC socket.

17. To completely disconnect AC power from this apparatus’ external power supply, the

power supply plug must be unplugged at the AC socket.

1.2 Battery precautions

Keep batteries out of the reach of children.

Observe and install batteries according to the correct polarity as marked on the battery and

the transmitter battery compartment.

Do not expose the battery to excessive heat such as sunshine, fire, or other sources of

high heat.

Always consider the environment issues and follow local regulations when disposing of

batteries.

Remove depleted battery immediately.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type.

Use only disposable LR6(AA) alkaline or NiMH batteries.

Do not mix new batteries with old ones in the transmitter at the same time.

Do not use different battery types or models.

Do not use a leaking battery. If battery leakage occurs, avoid contact with skin. If contact

occurs, immediately wash thoroughly with soap and water.

If battery leakage comes into contact with your eyes, immediately flush with water and seek

medical attention.

Remove and safely store batteries away from the transmitter when the transmitter will not

be used for 60 or more days.

1.3 Notices

Old electrical and electronic appliances

6 en | Safety, precautions, and notices RE3 UHF

Wireless

21.06 | 3 | F.01U.362.808 Installation manual Electro-

Voice

Electrical or electronic devices that are no longer serviceable must be collected separately

and sent for environmentally compatible recycling (in accordance with the European Waste

Electrical and Electronic Equipment Directive). To dispose of old electrical or electronic

devices, you should use the return and collection systems put in place in the country

concerned.

by any means, electronic, mechanical, photocopying, recording, or otherwise, without the

prior written permission of the publisher. For information on getting permission for reprints

and excerpts, contact Electro-Voice. All content including specifications, data, and

illustrations in this manual are subject to change without prior notice.

1.4 Licensing, certifications, restrictions and manufacturers

declarations

Regarding handheld transmitters RE3-HHT-5L (480-524 MHz), RE3-HHT-5H (560-596 MHz),

RE3-HHT-6M (653-663 MHz), and bodypack transmitters RE3-BPT-5L (480-524 MHz), RE3-

BPT-5H (560-596 MHz), and RE3-BPT-6M (653-663 MHz):

1.4.1 FCC information

Certified under FCC Part 15 and FCC Part 74.

FCC ID: B5DH2285L, B5DH2285H, B5DH2286M, B5DB1245L, B5DB1245H, B5DB1246M.

RE3

UHF Wireless Safety, precautions, and notices | en 7

Electro

-Voice Installation manual 2021.06 | 03 | F.01U.362.808

NOTE: Regarding RE3-HHT-6M (653-663 MHz) and RE3-BPT-6M (653-663 MHz); use of

frequencies beginning at 653.000 MHz up to 657.000 MHz is covered under FCC Part 74 ID

numbers B5DH2286M and B5DB1246M, and require an LPAS user license, however use of

frequencies between 657.025 up to 663.000 MHz is covered under FCC Part 15, and do not

require an additional user license. For more information, see

https://www.fcc.gov/consumers/guides/operation-wireless-microphones.

CAUTION: Changes or modification made by the user could void the user’s authority to

operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

1.4.2 IC (Industry Canada)

FCC Supplier’s Declaration of Conformity

47 CFR, Section 2.1077 Compliance

Information

Product Identifier:

Electro-Voice:

RE3 Wireless Receiver, AASP Active Antenna Splitter, ALPA

Active Log Periodic Antenna, RFAMP Antenna Booster, BC2

Battery Charger

Responsible Party – U.S. Contact Information

Bosch Security Systems, Inc.

130 Perinton Parkway

Fairport, NY 14450

USA

Tel: +1 (585) 223-4060

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not be

8 en | Safety, precautions, and notices RE3 UHF

Wireless

21.06 | 3 | F.01U.362.808 Installation manual Electro-

Voice

Certified in Canada by IC under RSS-102, and RSS-210, and RSS-Gen

IC: 1321A-RE3HHT488, 1321A-RE3HHT560, 1321A-RE3HHT653, 1321A-RE3BPT488, 1321A-

RE3BPT560, 1321A-RE3BPT653.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique

de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is

subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

NOTE: Regarding RE3-HHT-6M (653-663 MHz) and RE3-BPT-6M (653-663 MHz); the use of

frequencies between 653.025 up to 663.000 MHz, please check the Canada’s ISED

(Innovation, Science and Economic Development) website for the current information of the

license status of this band.

1.4.3 Licensing information

Licensing: A ministerial license to operate this equipment may be required in certain areas.

Consult your national authority for possible requirements. Changes or modifications not

expressly approved by Electro-Voice could void your authority to operate the equipment.

Licensing of Electro-Voice wireless microphone equipment is the user’s responsibility, and

licensability depends on the user’s classification and application, and upon the selected

frequencies on which it will operate. Electro-Voice advises the user to contact the

appropriate telecommunications authority concerning proper licensing, and before

selecting and ordering frequency bands.

1.4.4 EU (European Union)

The CE Declaration of Conformity can be obtained and downloaded from:

www.electrovoice.com

This Equipment is in compliance with the following directives:

2011/65/EU RoHS Directive

2012/19/EU WEEE Directive

2014/53/EU RED Directive

Regarding (applies to) handheld transmitter RE3-HHT-5L (480-524 MHz), RE3-HHT-5H (560-

596 MHz), RE3-HHT-6M (653-663 MHz), RE3-HHT-8M (823-865 MHz), and bodypack

transmitter RE3-BPT-5L (480-524 MHz), RE3-BPT-5H (560-596 MHz), RE3-BPT-6M (653-663

MHz), and RE3-BPT-8M (823-865 MHz):

This equipment is intended for use in wireless microphone applications.

RE3

UHF Wireless Safety, precautions, and notices | en 9

Electro

-Voice Installation manual 2021.06 | 03 | F.01U.362.808

Some countries in the EEA (European Economic Area) have restrictions placed on this

equipment. If an EEA country is not listed it did not have any restrictions of the product at

the time this document was published.

The country codes used in regard to these restrictions are the following:

Austria (AT), Belgium (BE), Cyprus (CY), Denmark (DK), Germany (DE), Greece (EL), Spain

(ES), Ireland (IE), Iceland (IS), Latvia (LV), Lithuania (LT), Malta (MT), Norway (NO), Slovakia

(SK), Sweden (SE) and United Kingdom (UK).

Listed below are these restrictions:

Transmitters in the ranges, 488 – 524 MHz, 560 – 596 MHz and 653 – 663 MHz,

require a license in the following countries: AT, BE, CY, DE, IE, LV, LT, SK, SE, UK.

Transmitters in the ranges, 488 – 524 MHz, 560 – 596 MHz and 653 – 663 MHz,

require the transmitter be used in TV white spaces: AT, DK, IS, MT, NO, ES.

Transmitters in the ranges, 488 – 524 MHz, 560 – 596 MHz and 653 – 663 MHz, if

used outdoor will have geographical restrictions of operation in the United

Kingdom (UK)

Transmitters in the range, 823 – 865, require a license for use in the 823 – 832 MHz

range in the following countries: AT, BE, CY, EL, IE, LV, LT, UK.

Transmitters in the range, 488 – 524 MHz, may only use the range 510 – 524 MHz in

Norway (NO).

Note: TV white spaces are gaps between operating TV broadcast stations where there are

no active TV broadcasts.

Always consult your national authority before placing equipment into operation as

requirements and spectrum usage can change.

1.4.5 AU and NZ

This device operates under an ACMA class license and must comply with all the terms of

that license including operating frequencies.

10 en | Short information RE3 UHF

Wireless

21.06 | 3 | F.01U.362.808 Installation manual Electro-

Voice

2Short information

The following table lists products in a family, with CTN (Commercial Type Number) and

identifying product name DESCRIPTION.

CTN

DESCRIPTION

RE3-ND76-5L

Handheld set with ND76 head 488-524MHz

RE3-ND76-5H

Handheld set with ND76 head 560-596MHz

RE3-ND76-6M

Handheld set with ND76 head 653-663MHz

RE3-ND76-8M

Handheld set with ND76 head 823-865MHz

RE3-ND76-T

Handheld set with ND76 head 803-806MHz

RE3-ND86-5L

Handheld set with ND86 head 488-524MHz

RE3-ND86-5H

Handheld set with ND86 head 560-596MHz

RE3-ND86-6M

Handheld set with ND86 head 653-663MHz

RE3-ND86-8M

Handheld set with ND86 head 823-865MHz

RE3-ND86-T

Handheld set with ND86 head 803-806MHz

RE3-ND96-5L

Handheld set with ND96 head 488-524MHz

RE3-ND96-5H

Handheld set with ND96 head 560-596MHz

RE3-ND96-6M

Handheld set with ND96 head 653-663MHz

RE3-ND96-8M

Handheld set with ND96 head 823-865MHz

RE3-ND96-T

Handheld set with ND96 head 803-806MHz

RE3-RE420-5L

Handheld set with RE420 head 488-524MHz

RE3-RE420-5H

Handheld set with RE420 head 560-596MHz

RE3-RE420-6M

Handheld set with RE420 head 653-663MHz

RE3-RE420-8M

Handheld set with RE420 head 823-865MHz

RE3-RE420-T

Handheld set with RE420 head 803-806MHz

RE3-RE520-5L

Handheld set with RE520 head 488-524MHz

RE3-RE520-5H

Handheld set with RE520 head 560-596MHz

RE3-RE520-6M

Handheld set with RE520 head 653-663MHz

RE3-RE520-8M

Handheld set with RE520 head 823-865MHz

RE3-RE520-T

Handheld set with RE520 head 803-806MHz

RE3-BPOL-5L

Bodypack set, omni lavalier 488-524MHz

RE3-BPOL-5H

Bodypack set, omni lavalier 560-596MHz

RE3-BPOL-6M

Bodypack set, omni lavalier 653-663MHz

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Electro-Voice Mikrofon Handbücher

Electro-Voice

Electro-Voice 634A Bedienungsanleitung

Electro-Voice

Electro-Voice DL42 Bedienungsanleitung

Electro-Voice

Electro-Voice Cardinal Bedienungsanleitung

Electro-Voice

Electro-Voice 633 Dimensionsleitfaden

Electro-Voice

Electro-Voice Cobalt Co9 Bedienungsanleitung

Electro-Voice

Electro-Voice PL76 Montageanleitung

Electro-Voice

Electro-Voice MC300 Bedienungsanleitung

Electro-Voice

Electro-Voice 1776B Bedienungsanleitung

Electro-Voice

Electro-Voice PL78 Bedienungsanleitung

Electro-Voice

Electro-Voice US621L Bedienungsanleitung

Electro-Voice

Electro-Voice N/D308B Montageanleitung

Electro-Voice

Electro-Voice RE36N/D Bedienungsanleitung

Electro-Voice

Electro-Voice RE92L Bedienungsanleitung

Electro-Voice

Electro-Voice RE38N Bedienungsanleitung

Electro-Voice

Electro-Voice Cobalt Co11 Bedienungsanleitung

Electro-Voice

Electro-Voice CH230WX Bedienungsanleitung

Electro-Voice

Electro-Voice US637A Bedienungsanleitung

Electro-Voice

Electro-Voice PL80c Bedienungsanleitung

Electro-Voice

Electro-Voice Cobalt Co4 Bedienungsanleitung

Electro-Voice

Electro-Voice MC200 Bedienungsanleitung

Electro-Voice

Electro-Voice R300 Bedienungsanleitung

Electro-Voice

Electro-Voice PolarChoice PC Plus-12 Bedienungsanleitung

Electro-Voice

Electro-Voice RE920Tx Bedienungsanleitung

Electro-Voice

Electro-Voice PL44 Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

Shure

Shure WH30TQG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

Shure

Shure KSM141 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

Shure

Shure MXA710 Series Bedienungsanleitung