ELECTROCOMPANIET ECC-1 Bedienungsanleitung

ECC - 1

Illustration 1 – Back panel

Illustration 2 – Front panel

Unpacking the ECC-1

Immediately upon receipt of the ECC-1, inspect the carton for possible damage during shipment.

The carton and packaging have been designed to provide the safest possible protection during

transport of your product. Unpack the unit carefully. Save all packaging materials for future

shipment.

The contents of the carton

1 piece Electrocompaniet ECC-1

1 piece AC mains cord.

1 piece inspection card.

1 piece user manual

If anything is missing or any transport damages is discovered, please contact your dealer for

assistance.

Send also a report to [email protected] with all the information from the inspection

card. Please include model, serial no, packaging information and person responsible for final

inspection in your e-mail. This is part of our quality system and this information helps us to

continuously improve our quality control.

Set up procedure

Before connecting the ECC-1 to the mains, check that the main voltage indicated on the rear panel

corresponds to the line voltage in the territory where you intend to use the unit.

How to avoid damages

Do not under any circumstance connect or disconnect equipment when power is turned on.

The design of the RCA plug generates a huge transient when inserted.

Connecting or disconnecting equipment with the power on can result in severe damage to both

speakers and amplifier.

How to avoid noise problems

The ECC-1 contains delicate circuits that are sensitive to magnetic stray fields.

The unit should not be placed near main transformers, TV sets, etc. Care should also be taken

regarding placement of the interconnect cables. Do not run interconnect cables in parallel with main

cords or speaker cables. Keep interconnect cables as short as possible.

How to connect your system

See illustration 1.

Outputs

Balanced analogue operation:

Use an XLR interconnect and connect the right and left outputs on the ECC-1 to the right and left

inputs on the integrated amplifier or preamplifier

Unbalanced analogue operation:

Use Phono interconnects and connect the right and left outputs on the ECC-1 to the right and left

inputs on the integrated amplifier or preamplifier

S/P DIF digital operation:

Use a 75-ohm coaxial digital cable from the ECC-1 to the digital input on your DAC.

Front panel

See illustration 2.

The main switch is located on the centre of the front panel.

The four buttons on the right-hand side of the front panel is used to play, stop, eject and skip to

previous/next track.

Function Button

Play Up button

Stop Down button

Eject Down button (hold button pressed until tray

eject)

Previous track Left button

Next track Right button

Navigator window

The navigator window is located on the left side and shows what track is playing, time left etc.

How to power up your system

You should always power up your system in the following order:

First turn on the ECC-1, and then turn on the amplifiers.

When switching off your system

First turn off the amplifiers, and then turn off the ECC-1.

XLR configurations

XLR output: 1 = ground 2 = positive 3 = negative

Technical specifications ECC-1

The following technical data were measured on randomised test objects and are typical data.

All measurements are made at 120V / 240V // 50Hz / 60Hz

Measurements

Output impedance 100 ohm

Output level 4,5Vrms

Noise floor (0 dB gain) < -130 dB

Frequency deviation < 0.05 dB

Channel separation > 110 dB

THD + N < 0.002%

Digital/Analogue conversion 24 bit, 192 kHz

Dynamic range 120 dB

Power consumption (no load or signal) 35 W

Dimensions

Width 483 mm

Depth 389 mm

Height 105 mm including feets

Weight 9 kg

Specifications are subject to change without further notice.

Important Notice

For optimal sonic performance, the ECC-1 should be burned in for a minimum time of 72 hours.

If the ECC-1 has been switched off, allow two hours of warm-up for optimal sonic performance.

Proper ventilation is important.

Never cover the ventilation area.

A good rule of thumb is to allow at least 3 - 5 cm (1 - 2 inches) of air sidewise, and 5 – 8 cm

(2 - 3 inches) above the ECC-1.

If service is needed

Your dealer will have all relevant information regarding the service centre in your area and will

ensure that your unit is serviced with minimum delay.

It is our general policy to have your unit returned to you within five working days.

This is an average time and can vary locally, depending on the workload at that particular service

centre.

If, for some reason, there are no service facilities available in your country, please ship the unit to

the following address:

ELECTROCOMPANIET AS,

BREIVIKVEIEN 7,

4120 TAU,

NORWAY

Switchboard: +47 51 74 10 33 Fax: +47 51 74 10 10 Service: +47 51 74 10 23

E-mail: [email protected]

Web: www.electrocompaniet.no

Service department: [email protected]

When shipping a product to the factory for service, always include the following:

1. A sales slip or other proof of purchase if repair is claimed under warranty.

2. A proforma invoice with value of goods, stating that the amplifier is being returned to Norway for

repair.

3. An accompanying letter describing faults, symptoms, or problems with the unit.

4. Always ship the unit in its original carton and packaging material to prevent damage in transit.

Electrocompaniet will not cover damages incurred in transit.

If you require further information concerning the operation of the unit or if you have any questions

related to service, please do not hesitate to contact your dealer or national distributor.

Inhaltsverzeichnis

Andere ELECTROCOMPANIET Verstärker Handbücher

ELECTROCOMPANIET

ELECTROCOMPANIET AW 800 M Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET ECI2 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET AW 180 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET EC 4.7 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET ECI 6DX Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET AW 120 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET EC 4.7 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET AW 180 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET ECI4 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET AW-250 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET EC 4.9 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET ECP 2 MKII Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET AW 250R Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET ECI 80D Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET AW 2x120 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET AW400 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET ECI 6 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET AW220 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET ECI3 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET PI-1 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET EC 4.8 MKII Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET EC-3 Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET ECI 6D Bedienungsanleitung

ELECTROCOMPANIET

ELECTROCOMPANIET ECP 2 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung