Electrolux E30GC70FSS3 Bedienungsanleitung

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

If the information in this manual is not followed exactly, a fire or explosion may

result causing property damage, personal injury or death.

FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

-- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

-- Installation and service must be performed by a qualified installer,

service agency orthe gas supplier.

Gas Cooktop

Dimensions

Gas Cooktop

Cutout Dimensions Figure I

281/2(72.4) 193/4(50.2)

36" GasCooktoL_ 33 7/8(86.1) 341/4(87) 19 1/8(48.6) 193/4(50.2)

All dimensions are stated in inches and (cm).

DimensionH includesa 5" (12.7cm) spaceunderneaththe cooktop for connectionto gassupplyline.

NOTE: Wiring diagrams for this cooktop are enclosed in this booklet

Printedin Canada

8 (20.3)

318205451 (1302) Rev.B

English - pages 1-9

Espahol - p_iginas 10-18

Fran_ais - pages 19-28

Notes - pages 29-30

Wiring Diagram 31-32

important Notes to the Installer

1. Read all instructions contained in these installation

instructions before installing the cooktop.

2. Remove all packing material before connecting the

electrical supply to the cooktop.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

5. Note: For operation at 2000 ft. elevations above see

level, appliance rating shall be reduced by 4 percent

for each additional 1000 ft.

important Note to the Consumer

Keep these instructions with your Use and Care Guide for

future reference.

IMPORTANT SAFETY

INSTRUCTION

Installation of this cooktop must conform with local

codes or, in the absence of local codes, with the National

Fuel Gas Code ANSI Z223.1/NFPA 54 in the United

States, or in Canada, with the Canadian Fuel Gas Code,

CAN/CGA B149 and CAN/CGA B149.2.

• When installed in a manufactured (mobile) home

installation must conform with the Manufactured

Home Construction and Safety Standard, title 24 CFR,

part 3280 [Formerly the Federal Standard for Mobile

Home Construction and Safety, title 24, HUD (part

280)] or, when such standard is not applicable, the

Standard for Manufactured Home Installation, ANSI/

NCSBCSA225.1 or with local codes where applicable.

This cooktop has been design certified by CSA

International. As with any appliance using gas and

generating heat, there are certain safety precautions you

should follow. You will find them in the Use and Care

Guide., read it carefully.

Air curtain or other overhead hoods, which operate

by blowing a downward air flow on to a range, shall

not be used in conjunction with gas ranges other

than when the hood and range have been designed,

tested and listen by an independent test laboratory

for use in combination with each other.

Be sure your cooktop is installed and grounded

properly by a qualified installer or service

technician.

This cooktop must be electrically grounded in

accordance with local codes or, in their absence,

with the National Electrical Code ANSI/NFPA

No. 70--latest edition in the United States, or in

Canada, with the Canadian Electrical Code, CSA

C22.1 Part 1.

The burners can be lit manually during an

electrical power outage. To light a burner, hold a

lit match to the burner head, then slowly turn the

Surface Control knob to LITE. Use caution when

lighting burners manually.

Do not store items of interest to children in

cabinets above the cooktop. Children could be

seriously burned climbing on the cooktop to reach

items.

To eliminate the need to reach over the surface

burners, cabinet storage space above the burners

should be avoided.

Adjust surface burner flame size so it does not

extend beyond the edge of the cooking utensil.

Excessiveflame is hazardous.

Never use your cooktop for warming or heating

the room. Prolonged use of the cooktop without

adequate ventilation can be hazardous.

Do not store or use gasoline or other flammable

vapors and liquids near this or any other

appliance. Explosions or fires could result.

The electrical power to the cooktop

must be shut off while gas line connections are

being made. Failure to do so could result in serious

injury or death.

13"(33cm)

Max.Depth

ForCabinet

InstalledAbove

Cooktop.

18"Min.

(45.7cm)

11/2"(3.8cm)MinimumDistance

BetweenRearEdgeofCutout

andNearestCombustibleSurface

AboveCountertop.

--T!

Clearance

24" (6! cm)

To eliminate the risk of

burns or fire from reaching over heated

surfaces, cabinet storage space located

above the cooktop should be avoided.

If cabinet storage is provided, risk can

be reduced by installing a range hood

that projects horizontally a minimum of

5" (12.7 cm) beyond the bottom of the

cabinets.

Drawers Cannot Be Used with This

Cooktop Since Burner Box Extends

3%2" (8.02 cm) Below Surface of

Countertop.

36" Cooktop 36" (91.4 cm)

7"(17.8 cm)

Figure 2 - CABINET DESIGN

30" (76.2 cm)

Min. Clearance

Between

the Top of

the Cooking

Platform and

Unprotected

Wood or Metal

Cabinet

7" (17.8 cm)

Typical Under

Oven Counter Installation of an Electric Built-in

with a Cooktop Mounted Above

All mounting hardware must be

used to secure the built-in oven to

the cabinets. Refer to the built-in

oven installation instructions.

Junction box must

be located approx.

3" to the left of

the built-in oven

cutout.

This cooktop may

be installed over

certain built-in elec-

tric oven models.

Side filler panels are necessaryto

isolate the unit from adjoining

cabinets. Panel height should allow

for installation of approved cooktop

models. See "Typical Gas Cooktop

Installation Over an Electric Built-in

Oven Installed Under the Counter" on

next page.

208/240 Volt

grounded junction

box for built-in oven.

36"

(91.4 cm)

Min.

Use 3/4" (1.9 cm)

plywood, installed

on two runners,

flush with toe plate.

Must be capable of

supporting 200 Ibs.

Cut an opening in wood base minimum 4"

(10.2 cm) x 4" (10.2 cm) to route armored

cable to junction box.

4 1/2" (11.4 cm)

Max.*

If no cooktop is installed

directly over the oven unit,

5" (12.7 cm) maximum is

allowed.

(76.2 cm) (71.8 cm)

Figure 3

(73.3 cm) (72.4 cm) 73.7 cm (61 cm)

Typical Gas Cooktop Installation Over an Electric Built-

in Oven Installed Under the Counter

I I8" (45.7 cm) Max. ----'_I I

Manifold Pil

Flexible Connector

Wall Oven Cabinet

Cabinet sides or

filler panel

Flare (12.7 cm)(16.5 cm)

Union

Flare

Union

120V/6OHz

Grounded

Outlet

Pressure

Regulator

Shutoff

(Tobe

shut-off valve op

tion)

4" (10.2 cm)

Right Side

of Cabinet

for

_ra-

Front

Wall Oven

Side view

Figure 4

Wall Outlet Location

, 12,, --_

I 1 0 "

, Recommended area for

'12OV grounded outlet

u on rear wall.

CL_olFUL_ET 22 "

:NOTE: If an outlet

J is not available, I

: have one installed by I

t a qualified technician.

It OF UNIT

Figure 5

Cooktop Installation

1. Visually inspect the cooktop for damage.

2. Set the cooktop into the countertop cutout.

To clamp down, insert an angle bracket into the slot

on each side of the unit as shown. Run thumb screw

up through the bracket, up against the bottom of the

counter. Tighten until the unit draws down and is secure.

Provide an Adequate Gas Supply

This cooktop is designed to operate on natural gas at 4"

of manifold pressure only.

A pressure regulator is connected in series with the

manifold on the cooktop and must remain in series with

the supply line.

For proper operation, the maximum inlet pressure

to the regulator must be no more than 14" of water

column (W.C.) pressure.

For checking the regulator, the inlet pressure must be at

least 1" (or 2.5 kPa) greater than the regulator manifold

pressure setting. The regulator is set for 4" of manifold

pressure, the inlet pressure must be at least 5".

The gas supply line to the range should be 1/2" or 3/4"

pipe.

LP/Propane Gas Conversion

This appliance can be used with Natural gas or LP/

Propane gas. It is shipped from the factory for use with

natural gas.

A kit for converting to LPgas is supplied with your

cooktop. The kit is marked "FOR LP/PROPANEGAS

CONVERSION".

NOTE: Do not use caulking compound; cooktop should

be removable for service when needed.

Clamp Down Information

Once the cooktop is installed in the counter opening,

you must clamp the unit down as shown.

Seal

Cooktop x_ _ Countertop

Angle

Bracketl_t(

Figure 6

Thumb

Screw

The conversion must be performed by a qualified service

technician in accordance with the kit instructions and

all local codes and requirements. Failure to follow

instructions could result in serious injury or property

damage. The qualified agency performing this work

assumes responsibility for the conversion.

Failure to make the appropriate

conversion can result in serious personal

injury and property damage.

Important: Remove all packing material and

literature from cooktop before connecting gas and

electrical supply to cooktop.

install Pressure Regulator

Install the pressure regulator with the arrow on the

regulator pointing up toward the unit in a position

where you can reach the access cap.

Do not make the connection too tight.

The regulator is die cast. Overtightening may crack the

regulator resulting in a gas leak and possible fire or

explosion.

Manual GAS FLOW Pressure

Shutoff Flare _1_ Flare Regulator

Valve Union Union

On, ltr/ t t ....

Nipple Flexible Nipple Access

Off Connector Cap

All connections must be wrench-tightened

Figure 7

Assemble the flexible connector from the gas supply pipe

to the pressure regulator in the following order:

1. manual shutoff valve

2. 1/2" (1.3 cm) nipple

3. 1/2" (1.3 cm) flare union adapter

4. flexible connector

5. 1/2" (1.3 cm) flare union adapter

6. 1/2" (1.3 cm) nipple

7. pressure regulator

Use pipe-joint compound made for use with Natural and

LP/Propane gas to seal all gas connections. If flexible

connectors are used, be certain connectors are not

kinked.

The supply line must be equipped with an approved

manual shutoff valve. This valve should be located in the

same room as the cooktop and should be in a location

that allows ease of opening and closing. Do not block

access to the shutoff valve. The valve isfor turning on or

shutting off gas to the appliance.

Shutoff Valve -

Open position

Figure 8

Once regulator is in place, open the shutoff valve in the

gas supply line. Wait a few minutes for gas to move

through the gas line.

Check for leaks. After connecting the cooktop to the

gas supply, check the system for leaks with a manometer.

if a manometer is not available, turn on the gas supply

and use a liquid leak detector (or soap and water) at all

joints and connections to check for leaks.

Do not use a flame to check for leaks

from gas connections. Checking for leaks with a flame

may result in a fire or explosion.

Tighten all connections if necessary to prevent gas

leakage in the cooktop or supply line.

Check alignment of control knob valves after

connecting the cooktop to the gas supply to be sure the

cooktop manifold pipe has not moved. A misalignment

could cause the valve stems to rub on the control panel,

resulting in a gas leak at the valve.

Disconnect this cooktop and its individual manual

shutoff valve from the gas supply piping system during

any pressure testing of that system at test pressures

greater than 1/2 psig (3.5 kPa or 14" water column).

Isolate the cooktop from the gas supply piping

system by closing its individual manual shutoff valve

during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2 psig

(3.5 kPa or 14" water column).

Electrical Requirements

120 volt, 60 Hertz, properly grounded branch circuit

protected by a 15 amp circuit breaker or time delay fuse.

Do not use an extension cord with this cooktop,

Grounding Instructions

IMPORTANT Pleaseread carefully.

For personal safety, this appliance must be properly

grounded,

The power cord of this appliance isequipped with a

3-prong (grounding) plug which mates with a standard

3-prong grounding wall receptacle (see Figure 9) to

minimize the possibility of electric shock hazard from the

appliance.

The wall receptacle and circuit should be checked by

a qualified electrician to make sure the receptacle is

properly grounded.

Where a standard 2-prong wall receptacle is installed,

it is the personal responsibility and obligation of the

consumer to have it replaced by a properly grounded

3-prong wall receptacle.

Donot,underanycircumstances,cutor removethe

third (ground)prongfromthepowercord.

Disconnectelectricalsupplycordfrom

wallreceptaclebeforeservicingcooktop.

Preferred Method

Grounding type

wall receptacle

not, under any

circumstances, cut,

remove, or bypass

the grounding

prong.

Power supply cord with

3-prong grounding plug.

Figure 9

Model and Serial Number Location

The serial plate is located on the underside of the

cooktop (see Figure 10).

When ordering parts for or making inquires about your

range, always be sure to include the model and serial

numbers and a lot number or letter from the serial plate

of your cooktop.

Your serial plate also tells you the rating of the burners,

the type of fuel and the pressure the cooktop was

adjusted for when it left the factory.

rest level. Refer to Figs. 12 & 13 for correct and incorrect

burner cap placement. Once in place, you may check the

fit by gently sliding the burner cap from side to side (Fig.

14) to be sure it is centered and firmly seated. When the

burner cap lip makes contact inside the center of the

burner head you will be able to feel it. Please note that

the burner cap should NOT move off the center of the

burner head when sliding from side to side. NOTE: There

are no burner adjustments necessary on this cooktop.

Burner Cap

Burner Head "_ _ Burner

Cap Lip

Fig. 11

Correct Burner Cap _ Incorrect Burner Cap

Placement- Fig. 12 _ Placement- Fig. 13

Serial plate is

located under

the burner box.

Figure 10

Check Operation

Refer to the Use and Care Guide packaged with the

cooktop for operating instructions and for care and

cleaning of your cooktop.

Do not touch the burners. They may be hot enough to

cause burns.

1. Install Burner Caps

This cooktop is equipped with sealed burners. All pieces

are at their place. Take note where they are. Remove

all packaging material. Make sure the burner caps are

properly aligned and leveled. The burner cap lip (See Fig.

11) should fit snug into the center of burner head and

Fig. 14

2. Place the Grates on the cooktop

Be sure they are correctly located inside the stainless steel

surface.

ATTENTION:Do not slide the grates on the cooktop, doing

so can damage the surface.

36" Cooktop ONLY:Be surethe grates arecorrectly placedon

the cooktop asshown below. Heat shieldsmust be besidethe

knobs.

Fig. 15 Heat shields

Turn on Electrical Power and Open Main Shutoff

Gas Valve

Check the Igniters

Operation of electric igniters should be checked

after cooktop and supply line connectors have been

carefully checked for leaks and the cooktop has been

connected to electric power.

To operate the surface burner:

A. Push in and turn a surface burner knob to the

LITEposition. You will hear a small ticking noise;

this is the sound of the electric ignitor which

lights the burner.

B. After the burner lights, turn to the desired flame

size. The controls do not have to be set at a

particular mark. Use the marks as a guide and

adjust the flame as needed.

Adjust the "LO" or "SIMMER" Setting of Surface

Burner Valves (see Figure 16)

Push in and turn each control knob to the "LO"

(or "SIMMER") setting. The "LO" setting of each

burner has been set at the factory to the lowest

setting available to provide reliable re-ignition of the

burner. If it does not stay lit on the "LO" setting,

check the setting as follows.

Be careful when performing this

operation.

A. Allow cooktop to cool to room temperature.

B. Light all burners by turning each control knob to

LITEuntil burners ignite, and then set them at

"HI".

C. _ turn the knob of the burner you want to

adjust to the LOWEST POSITION.

D. If burner goes out, readjust valve as follows:

Remove the surface burner control knob, insert

a thin-bladed screw driver into the hollow valve

stem and engage the slotted screw inside. Flame

size can be increased or decreased with the turn

of the screw. To increase flame size turn the

screw counterclockwise and to decrease turn

clockwise. Adjust flame until you can quickly

turn knob from HI to LOWEST POSITIONwithout

extinguishing the flame. Flame should be as

small as possible without going out.

E. If you need to adjust another burner, repeat the

steps from A to D above until all burners operate

properly.

Hollow

Valve Stem_

Figure 16

When All Hookups are Complete

Make sure all controls are left in the OFFposition.

Make sure the flow of combustion and ventilation air to

the cooktop is unobstructed.

Before You Call for Service

Read the Before You Call for Service Checklist and

operating instructions in your Use and Care Guide.

It may save you time and expense. The list includes

common occurrences that are not the result of defective

workmanship or materials in this appliance.

Refer to the warranty in your Use and Care Guide for

our service phone number and address. Pleasecall or

write if you have inquiries about your product and/or

need to order parts.

LA INSTALACION Y EL SERVICIO DEBEN SER REAUZADOS POR UN INSTALADOR CALIFICADO.

IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL iNSPECTOR ELI__CTRICOLOCAL.

LEA Y GUARDE ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIAS

Si todas las instrucciones de _ste manual no son observadas a la letra, se puede

ocurrir incendios o explosiones que pueden causar daEos materiales, lesiones ola muerte.

PARA SU SEGURIDAD:

-- No almacene o utilice gasolina u otros vapores y liquidos inflamables cerca

de _ste o cualquier otro artefacto.

-- QUE HACER SI HAY FUGAS DE GAS :

• No intente de encender ningun artefacto

®No toque ningun interruptor el_ctrico; no utilice ningun aparato telef6nico en su edificio.

Llame inmediatamente el abastecedor de gas desde el tel_fono de un vecino.

Siga las instrucciones del abastecedor de gas.

En caso que no puede contactar el abastecedor de gas Ilame al departamento de

bomberos.

--La instalacion y el servicio t_lefonico deben ser realizados por un instalador

calificado, por un servicio tecnico certificado o por el abastecedor de gas.

Dimensiones

de la parrilla

de cocinar

2W' Min.

(6.4 cm Min.

Dimensiones

del hueco de

la parrilla de cocinar Figura I

Modelo 36" 30 (76.2)

36 (91.4) 213/4(55.2)

213/4(55.2) 41/4(10.8) 331/4(84.5) 19 (48.3)

Modelo 36" 281/2(72.4) 19 1/8(48.6) 195/4(50.2)

33 7/8(86.1) 341/4(87) 19 1/8(48.6) 193/4(50.2) 8 (20.3)

8 (20,3)

Todas las dimensiones se dan en pulgasdas (cm).

La dimensi6n H incluye un espacio de 5" pot debajo de la plancha de cocinar para la conex16n 318205451 (1302)Rev.B

de la linea de suministro de gas. English- pages 1-9

Espahol - p_iginas 10-18

NOTA: Se adjunta los diagramas de cables de esta plancha de codnar con el libreta. Fran_ais-pages19-28

Notas - p_iginas 29-30

Imprimido en Canada Diagramade la instalaci6nal_imbrica- p_iginas31-32

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Electrolux Kochfeld Handbücher

Electrolux

Electrolux EW36IC60LB Montageanleitung

Electrolux

Electrolux EW30GC60IS Bedienungsanleitung

Electrolux

Electrolux EW36CC55GW - 36in Electric Cooktop Bedienungsanleitung

Electrolux

Electrolux EHG735SP Bedienungsanleitung

Electrolux

Electrolux Electric cooktops Montageanleitung

Electrolux

Electrolux ECCI3668AS Bedienungsanleitung

Electrolux

Electrolux EI30EC45KB1 Bedienungsanleitung

Electrolux

Electrolux Competence Series Bedienungsanleitung

Electrolux

Electrolux EW30EC55G - 30" Electric Cooktop Bedienungsanleitung

Electrolux

Electrolux 318 200 687 Bedienungsanleitung

Electrolux

Electrolux E36EC70FSS - 36" Drop-In Electric Cooktop Gebrauchsanweisung

Electrolux

Electrolux EW30GC55G S Bedienungsanleitung

Electrolux

Electrolux E36IC75FSS4 Bedienungsanleitung

Electrolux

Electrolux E36EC65ESS - Icon 36"Drop-in Electric... Bedienungsanleitung

Electrolux

Electrolux E36EC65ESS - Icon 36"Drop-in Electric... Bedienungsanleitung

Electrolux

Electrolux EI30GS55L Merkblatt

Electrolux

Electrolux EW30EC55G - 30" Electric Cooktop Bedienungsanleitung

Electrolux

Electrolux ICON E30GC64ESS Bedienungsanleitung

Electrolux

Electrolux EW30EC55GB - 30" - Electric Cooktop Gebrauchsanweisung

Electrolux

Electrolux E36IC80ISS - 36" Induction Cooktop Kurzanleitung

Electrolux

Electrolux EW30EC55G - 30" Electric Cooktop Bedienungsanleitung

Electrolux

Electrolux E30GC74GPS - 30" Pro-Style Gas Rangetop Bedienungsanleitung

Electrolux

Electrolux EW30IC60LB Montageanleitung

Electrolux

Electrolux EW36IC60I - 36 in. Induction Cooktop Bedienungsanleitung

Beliebte Kochfeld Handbücher anderer Marken

Bonnet

Bonnet OPTIMUM 700 Betriebsanleitung

Jenn-Air

Jenn-Air JGCP430 Bedienungsanleitung

Frigidaire

Frigidaire FES367FCC Kurzanleitung

Ztove

Ztove EZ2 DUO Bedienungsanleitung

Kleenmaid

Kleenmaid cooking GCTK9011 Installationsanleitung

Jenn-Air

Jenn-Air JGC2536EB00 Bedienungsanleitung

Waldorf

Waldorf RN8603E-B Bedienungsanleitung

Whirlpool

Whirlpool SMP658CNEIXL Bedienungsanleitung

Wolf

Wolf CI243C/B Bedienungsanleitung

Fulgor Milano

Fulgor Milano F5PGK305S1 Bedienungsanleitung

GE JP389 Bedienungsanleitung

Wells

Wells WV-2HFG Bedienungsanleitung

IKEA

IKEA Lagan HGA4K Bedienungsanleitung

Samsung

Samsung NA36N9755 Bedienungsanleitung

Miele

Miele KM 404 Bedienungsanleitung

Lacor

Lacor 69562 Technisches Datenblatt

Keating Of Chicago

Keating Of Chicago MG-2 Bedienungsanleitung

Jenn-Air

Jenn-Air CCE1400 Bedienungsanleitung