Electrolux GHS605W Handbuch

Ga cooktop

In truction and in tallation manual

Model : GHS605W, GHS605S, GHC605W, GHC605S, GHC615W, GHC615S,

GHS915W, GHS915S, GHC935W, GHC935S, 72J315W, 72J315S

CONTENTS

SUBJECT PAGE

GAS COOKTOPS.......................................1

General Warnings

Cooktops (Generally)

GAS COOKTOPS.......................................2

nstallation

Servicing

Cleaning

USING YOUR COOKTOP ..........................3

Controls

Lighting Burners

electronic ignition

push button ignition

USING YOUR COOKTOP ..........................4

Hotplates

choice of hotplate

pots and pans

CLEANING AND CARE .............................5

Enamel

Stainless Steel

Trivets, Burner-caps and Crowns

gnition Electrode

TROUBLESHOOTING................................6

INSTALLATION ..........................................7

nstallation nstructions

nstallation Procedure

bench cut-out

combustible materials

optional barrier

fitting cooktop into bench

SUBJECT PAGE

INSTALLATION ..........................................8

Operation on NG/SNG

Gas Connection

supply pipe sizing

INSTALLATION ..........................................9

Elbow positioning

Check the gas supply

LPG conversion

INSTALLATION ........................................10

LPG conversion continued

INSTALLATION.........................................11

Battery Connection

Electrical Connection

Testing Appliance Operation

INSTALLATION ........................................12

Testing Appliance Operation continued

WARRANTY..............................................13

GAS COOKTOPS

Read the following carefully to avoid an electric shock or fire.

General Warnings

• This appliance is not suitable for use by young children or infirm persons, without supervision.

• Young children should be supervised to ensure they do not play with this appliance.

• During use, this appliance becomes hot. Care should be taken to avoid touching

hot surfaces.

• This appliance must not be used as a space heater.

• Keep vents clear of obstructions.

• n order to avoid a fire, the appliance must be kept clean.

• Do not spray aerosols in the vicinity of the appliance when it is in operation.

• Do not store flammable materials in or under the appliance, e.g. aerosols.

Cooktops (Generally)

• Do not allow pots to boil dry, as damage to both pan and cooktop may result.

• Do not operate the cooktop for an extended period of time without a pot or pan on

the hotplate.

• Do not allow large cookware to overhang the cooktop onto the adjacent benchtop.

This will cause scorching to the benchtop surface.

• Do not allow cooking pots or pans to intrude into the area which is close to the controls.

• Ensure burner caps, crowns and trivets are properly located. (See Figure 1)

Figure 1

• For maximum stability, ensure pots and pans are centrally located on the trivets.

• Handles should be turned away from the front of the bench to avoid accidents.

burner cap

burner crown

ignition electrode

injector

2. GAS COOKTOPS

NOTE: You must read these warnings carefully before installing or using the cooktop.

f you need assistance, contact your Customer Care Department.

The manufacturer will not accept liability, should the instructions below or any other

safety instructions incorporated in this book be ignored.

Installation

• An authorised person must install this appliance and UST provide a certificate

of compliance.

• Before using the appliance, ensure that all packing materials are removed from the appliance.

• n order to avoid any potential hazard, the installation instructions in this booklet, and any

labels on the appliance must be followed.

• Ensure that all specified vents, openings and air spaces are not blocked.

• Where the appliance is built into a benchtop, the benchtop material must be capable of

withstanding 85°C.

Servicing

• Servicing UST only be carried out by authorised personnel.

• To maintain safe operation, it is recommended that the product be inspected every five years

by an authorised serviceperson.

• For appliances supplied with a supply cord, if the supply cord is damaged, it must be replaced

by an authorised service person in order to avoid a hazard.

• For models with battery ignition, the battery will require periodic replacement. (See page 11)

NOTE: The battery is a perishable item and is not covered by the warranty.

Cleaning

• Always ensure the appliance is turned off before cleaning.

• This appliance contains aluminium fittings. Do not use caustic based cleaners.

• Do not use steam cleaners, as this may cause moisture build up on electrical components.

• Always clean the appliance immediately after any food spillage.

• DO NOT place burner caps, crowns or griddle plate in a dishwasher.

3. USING YOUR COOKTOP

Congratulations

Congratulations and thank you for choosing our Product. We are sure you will find your new

cooktop a pleasure to use and a great asset to your cooking. Before you use the cooktop, we

recommend that you read through the whole user manual which provides the description of the

cooktop and its functions. To avoid the risks that are always present when you use a gas

appliance, it is important that the cooktop is installed correctly and that you read the safety

instructions carefully to avoid misuse and hazards. For future reference, please store this booklet

in a safe place.

Using Your Cooktop

Aerosol sprays

Do not spray aerosols in the vicinity of this appliance while it is in operation as aerosols

can contain flammable propellants.

Warning – Ventilation

Where this appliance is installed in any confined area, the area must be properly

ventilated. t MUST NOT be used as a space heater.

Controls

• Each burner is controlled by a control knob. The markings on the

control panel indicate which burner the knob controls, and the

settings for that burner. (See Figure 2)

NOTE: Gas controls turn anticlockwise from ʻOFFʼ and have

limited movement.

Lighting burners

Electronic Ignition: These cooktops are fitted with mains powered or battery ignition. When the

appliance has been connected and the power is on, depressing any knob will release sparks to all

burners. (Except push button ignition. See push button ignition models.)

To light a burner, depress the corresponding knob and turn to the ʻH GHʼ position (while

depressing the knob). The knob may be released once the flame is established.

For Push Button Ignition odels, turn the knob to the ʻH GHʼ position and press the ignition button

down until the flame is established. The height of the flame can be varied by turning the knob

toward the ʻLOWʼ position.

• Keep hands clear of burners when lighting.

• If burner does not light within 5 seconds, turn knob to ʻOFFʼ position, allow gas

to disperse, then try lighting again.

• Burners UST be operated between ʻHIGHʼ and ʻLOWʼ

settings only.

n the absence of electrical power, carry out the ignition directly to the burner with a hand held

ignition source.

Figure 2

4. USING YOUR COOKTOP

Hotplates

Choice of Hotplate

For your convenience there is a choice of Hotplates –

• A small burner for special low heat and slow cooking.

• A medium burner for normal cooking and simmering.

• A large burner for fast heating and large pots and pans.

• A Wok burner for very fast heating using a Wok or large pot or pan.

To conserve gas, place the pan centrally over the burner and adjust the flame so that it does not

extend past the edge of the pan (Figure 3). Do not boil food too rapidly. A vigorous boil will not

cook food any faster, and will waste energy.

Pots and Pans

All common pots and pans; aluminium, stainless steel, cast iron, ceramic, etc., may be used on

your new gas model cooktop. Ensure that the pots or pans are steady and have flat bases to

avoid dangerous spill-over of hot liquids and wasted energy.

Figure 3

Never use asbestos mats, wire mats or grids, aluminium foil as it can lead to

overheating, cracked enamel. The warranty will be void if these utensils are used and

cause a failure. Woks should only be used on the wok burner and wok support trivet.

5. CLEANING AND CARE

Ensure the appliance is off and cool before cleaning.

Cleaning and Care

Enamel

Persistent stains may require rubbing with a nylon scourer or creamed powder cleansers.

Household enamel cleaners are available, follow the manufacturerʼs instructions in their use.

Harsh abrasive cleaners, powder cleaners, steel wool or wax polishes should not be used.

Stainless Steel

NOTE: Ensure any oil is cleaned off the hob before first use, otherwise it may cause the hob

to turn a yellowish colour.

All grades of stainless steel may stain, discolour or attain an adhering layer of grime in normal

operation. To achieve maximum surface appearance, stainless steel must be kept clean by

regularly using the following cleaning procedures, thus ensuring good performance and long

service life. Wash with warm soapy water and rinse with clean water. Where the stainless steel

has become extremely dirty with signs of surface discolouration, (due to periods of neglect or

misuse) use a stainless steel cleaner.

Do not use abrasive scourers or steel wool.

When removing these stains be sure to follow the polish or brushing lines.

Trivets, Burner-caps and Crowns

These can all be lifted off and removed for separate cleaning.

NOTE: When refitting the burner caps and crowns, ensure that they are correctly seated.

Ensure burner-caps and crowns are thoroughly dried after cleaning or spillage. When cleaning the

burner crowns, ensure that all the flame ports are free of any blockage. f necessary, use a

toothpick or brush to clear ports. The outer surface of the burner crowns have a polished finish

and extra care needs to be taken to avoid scratching this surface during cleaning. n instances of

heavy soiling, it may be necessary to apply a non-abrasive cleaning compound and rub with a cloth

until the soiling is removed and then finish with a soft, dry cloth.

NOTE: DO NOT place burner-caps and crowns in the dishwasher.

Ignition Electrode

GENTLY clean the electrode with a damp cloth to avoid lighting difficulties. Ensure the electrode is

dry before use.

Injector

Ensure the injector remains free of any foreign material. f necessary, use a thin piece of wire to

clear the orifice.

Benchtop or knobs

overheating.

Fault Possible Cause Remedy

6. TROUBLESHOOTING

f you have a problem with the cooktop, check the table below. You may be able to solve the

problem and this will save you from paying for a service call. You will have to pay for a service call

even in the warranty period if the problem is one listed below.

Table 1

Burner will not light even

though the sparker

is working.

No spark is obtained

when control knob is

activated.

Flames uneven or

tending to lift.

Turn on gas supply to appliance.

Turn knob on. (Refer page 3)

Ensure the knob you are turning

corresponds to the burner you

want to light.

Ensure that ports in ignition area

are clean and dry.

Dry or clean ignition electrode.

Ensure that crown is seated

properly so that the spark fires to

the receiving point in the burner

crown. (Refer Figure 1, page 1)

Ensure injector is clear of foreign

material

Gas supply valve turned off.

Control knob not on.

Wrong knob turned.

Port blockage in ignition area.

gnition electrode wet or dirty.

Sparking at wrong point because

of incorrectly fitted burner crown.

njector is blocked

Switch on electricity or check fuses.

Replace battery. (Refer page 11)

Reorient battery to correct

position. (Refer page 11)

Dry or clean ignition electrode.

Electricity supply is disconnected

or switched off.

Battery is flat.

Polarity wrong on battery.

gnition electrode wet or dirty.

Flame ports blocked or wet.

Burner cap/crown incorrectly fitted.

Clean or dry flame ports.

Ensure these components are

fitted correctly.

Flames not staying on

when knob released.

Knob not set between

ʻH GHʼ and ʻLOWʼ.

Knob MUST be set between

these positions.

Low heat, slow cooking. ncorrect cooking pot or pan

being used.

Refer to Figure 3. (page 4)

ncorrect cooking pot or pan used.

Pot or pan not located on burner

properly.

Check Figure 3 for correct pot or

pan to be used.

Ensure pot or pan is centrally

located on burner.

f the above points have been checked and there is still a problem with the cooktop, please call

the Service Centre.

Installation Instructions

This appliance must be installed by an

authorised person and in compliance with :

1. AS 5601 ʻGas Installationsʼ (Australia) or NZS

5261 ʻInstallation of Gas Burning Appliances

and Equipmentʼ (New Zealand) or the relevant

installation code for gas appliances of your

country.

2. The local gas fitting regulations, municipal

building codes, electrical wiring regulations and

any other relevant statutory regulations.

3. The particular instructions as given below. Before

commencing installation, check to ensure that the

appliance gas type given on the data plate on the

appliance corresponds with the type of gas to which

it is intended the appliance be connected.

4. A certificate of compliance MUST be given to the

customer after the appliance is successfully

installed.

Installation Procedure

1. The bench cutout should be made as per ʻBENCH

CUTOUT S ZEʼ table (Figure 4).

2. Adjacent walls, cupboards and protection for

combustible materials.

Refer to the Requirements of AS 5601 Section 5.12.1

regarding the necessary clearances.

3. Optional Barrier. A barrier can be installed to prevent

accidental contact with the cooktop base, where the base of

the cooktop is accessible from below (ie inside a cupboard,

etc). mpressions have been incorporated into the base to

ensure a minimum clearance of 10mm is maintained

between the base and the barrier. This barrier may be

made of any rigid material.

Ensure that the appliance is installed with Section 5.12.1 of

AS 5601 (Australia) or section 14.1 of NZS 5261 (New

Zealand), regarding clearances to combustible surfaces

and materials, and clearances to rangehoods and exhaust

fans.

To ensure clearances of 200mm from burners to vertical

combustible surfaces observe the dimensions shown in

Figure 5.

Clearances to combustible materials may be reduced if

combustible surfaces are protected in accordance with

clause 5.12.1.2 of AS 5601 (Australia) or section 14.1.2 of

NZS 5261 (New Zealand).

4. Fitting the cooktop into the bench. Carry out as follows:

• Place the seals supplied around the bench cut-out as

shown in Figure 6. Position them 6mm from the side

edges and 14mm from the front and rear edge, taking

care that the seals meet without overlapping.

7. INSTALLATION

130

min

490

570

135

min 120

min

470

830

Gas supply connection

Figure 5

Figure 4

Gas supply connection

14mm

6mm

seal

14mm

6mm

bench cut-out

Figure 6

INSTALLATION

•

• Position the cooktop so it is centred, then swing the

clamps under the benchtop and tighten (Figure 7).

• Remove excess seal.

Operation on N.G./S.N.G.

Regulator

An appliance regulator is provided. The regulator must be positioned so that the pressure test nipple is

accessible when the appliance is installed. Connect the gas supply to the ½” B.S.P. internal thread

inlet of the regulator. Refer to ʻbench cutoutʼ (Figure 4) for connection point position.

Regulators are supplied pre-adjusted and configured by the component maker for use with Natural

Gas. The appliance installer is not required to make an adjustment to obtain the correct outlet

pressure setting.

An arrow on the base of the regulator indicates the direction of gas flow when the inlet and outlet of

the regulator is orientated correctly. When the regulator has been fitted check for leaks from the

connections with soapy water.

Gas connection

This appliance is supplied for use with Natural Gas. However, it can e converted for use with

LPG. Refer to LP conversion on page 9 & 10.

Supply pipe sizing

The total hourly gas consumption for the appliance is shown on the data label. The required supply

pressure (i.e. at inlet to appliance regulator) for each gas type is shown on the data label, and given in

Table 2. Use this information in conjunction with the length of run, number of elbows, tees and bends,

the available service pressure and the supply requirements of other installed appliances to determine

a suitable pipe size. For assistance in this matter refer to the appropriate section of the nstallation

Code AS5601.

An AGA certified class B or D flexible connection may be used to connect the cooktop in accordance

with the AS5601 and in particular section 4.8. Where a hose assembly is used and the cooktop is in

the installed position, the hose assembly shall be suitable for connection to a fixed consumer piping

outlet located at a point 800 – 850mm above the floor and in the region outside the width of the

appliance to a distance of 250mm. The point of connection to consumer piping must be accessible

with appliance installed.

hob

seal

trivet

burner box

clamp

benchtop

screw

Figure 7

Fit the pull-down clamps supplied to ensure that the cooktop

cannot move after installation. Failure to fix the cooktop to the

bench could result in loosening of the gas connection through

movement of the cooktop and a gas leak may result.

Use the 4 clamps and 4 screws supplied in the parts bag.

•To assemble, attach the 4 clamps to each corner of the

burner box via the screws provided.

•When placing the cooktop in the cut-out, swing the clamps

parallel with the box to avoid interference with the cut-out.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Electrolux Kochfeld Handbücher

Electrolux

Electrolux E46GC67ESS - 46" Sealed Burner Gas Cooktop Bedienungsanleitung

Electrolux

Electrolux EI24EC15KS Bedienungsanleitung

Electrolux

Electrolux E30IC75FSS5 Bedienungsanleitung

Electrolux

Electrolux E36IC80ISS - 36" Induction Cooktop Bedienungsanleitung

Electrolux

Electrolux EW30EC55G - 30" Electric Cooktop Bedienungsanleitung

Electrolux

Electrolux E36EC75HSS1 Bedienungsanleitung

Electrolux

Electrolux E30IC75FSS - 30 Inch Drop-In Induction... Bedienungsanleitung

Electrolux

Electrolux 318 203 667 Bedienungsanleitung

Electrolux

Electrolux E36EC75DSS2 Bedienungsanleitung

Electrolux

Electrolux EW30EC55GS - 30" Electric Cooktop Bedienungsanleitung

Electrolux

Electrolux 584146 Bedienungsanleitung

Electrolux

Electrolux 36" Ceramic Bedienungsanleitung

Electrolux

Electrolux EW36CC55GW - 36in Electric Cooktop Bedienungsanleitung

Electrolux

Electrolux E30IC80QSS Bedienungsanleitung

Electrolux

Electrolux E30IC75FSS5 Benutzerhandbuch

Electrolux

Electrolux ICON E36IC75FSS Bedienungsanleitung

Electrolux

Electrolux Induction/2 - EW30CC55GW 30" Hybrid Cooktop Bedienungsanleitung

Electrolux

Electrolux E36GC65ESS - 30"""" Drop-in Gas Cooktop Bedienungsanleitung

Electrolux

Electrolux E30EC65ESS - 30 Inch Smoothtop Electric... Bedienungsanleitung

Electrolux

Electrolux EHT6047X Bedienungsanleitung

Electrolux

Electrolux EI30GS55L Merkblatt

Electrolux

Electrolux E36EC70FSS2 Bedienungsanleitung

Electrolux

Electrolux EW30IC60I S Bedienungsanleitung

Electrolux

Electrolux GAS COOKTOP Bedienungsanleitung

Beliebte Kochfeld Handbücher anderer Marken

Bonnet

Bonnet OPTIMUM 700 Betriebsanleitung

Jenn-Air

Jenn-Air JGCP430 Bedienungsanleitung

Frigidaire

Frigidaire FES367FCC Kurzanleitung

Ztove

Ztove EZ2 DUO Bedienungsanleitung

Kleenmaid

Kleenmaid cooking GCTK9011 Installationsanleitung

Jenn-Air

Jenn-Air JGC2536EB00 Bedienungsanleitung

Waldorf

Waldorf RN8603E-B Bedienungsanleitung

Whirlpool

Whirlpool SMP658CNEIXL Bedienungsanleitung

Wolf

Wolf CI243C/B Bedienungsanleitung

Fulgor Milano

Fulgor Milano F5PGK305S1 Bedienungsanleitung

GE JP389 Bedienungsanleitung

Wells

Wells WV-2HFG Bedienungsanleitung

IKEA

IKEA Lagan HGA4K Bedienungsanleitung

Samsung

Samsung NA36N9755 Bedienungsanleitung

Miele

Miele KM 404 Bedienungsanleitung

Lacor

Lacor 69562 Technisches Datenblatt

Keating Of Chicago

Keating Of Chicago MG-2 Bedienungsanleitung

Jenn-Air

Jenn-Air CCE1400 Bedienungsanleitung