Electrolux EGT 9425K Bedienungsanleitung

SERVICE MANUAL

C O N T E N T S

1. GENERAL NOTES 2

2. HOW DOES GAS BURNER OPERATE 3

3. COMPONENTS SPECIFICATION 4

4. TOOLS 6

5. REPAIR PROCESS 6

Remove he dir y oil from nozzle

Remove he gas valve

6. WIRING DIAGRAM 8

7. CONVERSION DETAILS 9

8. SPARE PARTS 11

9. TROUBLE SHOOTING 17

1. GENERAL NOTES

2. WARNING: For models which connect to mains electrical power, before exposing any of the

internal electrical wiring the appliance must be disconnected from electrical power by

unplugging the service cord from the electrical outlet. For models which connect to battery

power, before exposing any of the internal electrical wiring the appliance must be remove the

battery also.

3. Any servicing carried out on gas containing components where seals are broken including

manifold, regulator, valves and burner supply pipes should be followed by a leak test. Gross

leaks can be detected by connecting a manometer to the regulator test point, pressurising the

manifold and then shutting off the gas with a ball valve. A falling manometer reading indicates

a leak. mall leaks can be located with soap and water applied at the connection.

4. Burner supply pipes leading from the burner control to the burner should have their

compression fittings tightened firmly bu no over igh ened (If a torque spanner is used set

this to 10  12Nm). If the tubes are damaged they should be replaced. The soundness of the

connections on the burner supply tubes can be tested by blocking the injector orifice

temporarily, eg. by fitting an injector that has been blocked and leak testing the fittings.

5. When reassembling the appliance any ear h leads which have been disconnec ed mus be

re-connec ed.

6. Reassembly procedures are a reversal of removal procedures.

7. Replace the spare part with original spare parts. The modify part must not be used.

8. All the screws in this appliance have been designed for difference purpose. They must be use

in the right position and must be the right dimension. If there are any differences from the

original design they may have the serious accident.

2. HOW DOES GAS BURNER OPERATE

1. Gas tank

2. Low pressure regulator (Safe y warning: Do no use high pressure regulator)

3. Flexible rubber hose or copper tube

4. Elbow coupling gas with fibre washer (Warning: Do no use regular rubber washer)

5. 2 steps safety valve

6. Burner

7. Ignition switch

8. Battery 1.5V size D

9. park generator

10. park plug

Gas from the tank (1) is released from the low pressure regulator (2) into the hose or tube (3),

travelling pass the elbow coupling to the valve (4). To ignite the burner, press down and turn the

safety valve (5) counter-clockwise simultaneously. This opens up the valve, letting the gas to the

nozzle of the burner (6), and turns the ignition switch to on (7) at the same time. The electrical

current is automatically supplied from the battery to spark plug generator (8), and then to the pin

heads (9), causing the ignition (10). The burner is ignited and bursts into flame (11).

3. COMPONENTS SPECIFICATION

- Glass 3B = Float glass 8.0x460x760 mm

- Bottom plate forming=Zinc coat

- Knob= heat + flame resistance

- Washer= fiber

- Hose end=Brass (size1/2)

- Rubber grommet (glass model)

= ilicone heat resistance

- park generator 4p=1.5Vdc+90C+electrode10KV

Citi Gas Accessories

- hutter Aeration ( emi Papid)

(TH-0003/ZA)

- hutter Altration ( Triple Crown)

(TH-0003/ZB)

- Injector 2.1 ( emi Rapid)

(TH-0003/CD)

- Injector 4.0 (Triple Crown)

(TH-0003/ZA)

- crew, M4x0.7x10 IP

- crew, M4x0.7x18 H

- crew, M3x12T + B stainless

- crew, #6/32 x 9 PPZF

- crew, #8 x ½ T+ Z

4. TOOLS

- Nut spinner No. 7

- Philip / Flat screw driver

- panner No. 15

- Nozzle cleaner

- Gas leak detector

5. REPAIR PROCESS

5.1 Remove out the dirty oil from nozzle

1. Clean the head of nozzle with the cloth

2. Use the nozzle cleaner or the needle insert into the hole of nozzle.

3. Do repeat the step 1 and 2 for a few time until the nozzle is clean.

5.2 Removal of Hob & Access to Internal Components

1. Isolate the appliance from battery power.

2. Remove trivets and burners from hob.

3. Remove the control knobs from the valve shafts.

4. Remove burner mount retaining screws, 2 screws per burner and 4 on the wok burner (2.5mm

Torque crewdriver required).

5. For models with a separate button ignition system, remove the switch button and ignition pack

retaining nut. Alternatively, lift the hob sufficiently to access and release the ignition leads and

battery supply cable from the ignition pack.

6. The hob may now be lifted away from the appliance.

By removing the hob the following parts are accessible for service or replacement.

•Burner mounting cups.

•Burner supply tubes. Note: When fitting the burner tubes to the valves and burner

mounting cups the nuts should be fastened with a torque of 10-12Nm.

•Manifold & Valves. Note: To remove the manifold or valves it will be necessary

to isolate and disconnect the appliance from gas supply.

•witch harness assembly and low voltage wiring.

•Ignition spark plug and lead assemblies. These are fastened to the burner bases by retaining

clips, located on the underside of the burner base.

•Ignition pack. For models without a separate ignition switch this is clipped to the base or

attached with double sided adhesive. For models with a separate ignition switch this is

fastened to the hob with a retaining nut. Observe the active & neutral are correctly connected

in accordance with the markings on the ignition pack when replacing this unit.

6. WIRING DIAGRAM

7. CONVERSION DETAILS

The appliance is conver ible be ween Na ural Gas & LP.

Procedure

1. Turn off gas supply to appliance.

2. Disconnect appliance from electrical power.

3. Remove the trivets and the burner caps & distributors.

4. Remove the existing injectors and replace with the injectors shown in the table below.

5. Remove the control knobs to access the by-pass screw in the valve bodies.

6. Remove the regulator and replace with appropriate regulator or test point adapter as stated in

table below, and reconnect the appliance.

7. Turn on gas & check for leaks. Replace the Burner crowns & caps.

8. Check and adjust the test point pressure according to the procedure in the installation

instructions.

9. Manually light all burners with a hand held ignition source and operate burners at maximum.

Note: Do not reconnect the appliance to electrical power until this procedure is complete.

10. For each hotplate burner adjust the burner to minimum and screw in the bypass screw until a

small stable flame results. Adjust the burner to maximum and back to minimum to ensure

correct adjustment.

11. Re-connect to electrical power and check ignition.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Electrolux Kochfeld Handbücher

Electrolux

Electrolux GAS COOKTOP Bedienungsanleitung

Electrolux

Electrolux EW36EC55GB - 36" Smoothtop Electric Cooktop Kurzanleitung

Electrolux

Electrolux CHI643BA Betriebsanleitung

Electrolux

Electrolux EW30GC60IS Bedienungsanleitung

Electrolux

Electrolux E36EC75DSS1 Bedienungsanleitung

Electrolux

Electrolux ECCI3668AS Benutzerhandbuch

Electrolux

Electrolux EW36IC60LB1 Bedienungsanleitung

Electrolux

Electrolux E46GC67ESS - 46" Sealed Burner Gas Cooktop Bedienungsanleitung

Electrolux

Electrolux EW36IC60I S Bedienungsanleitung

Electrolux

Electrolux E30EC65ESS - 30 Inch Smoothtop Electric... Bedienungsanleitung

Electrolux

Electrolux EW30GC55GS - 30 Inch Gas Cooktop Bedienungsanleitung

Electrolux

Electrolux GAS COOKTOP Bedienungsanleitung

Electrolux

Electrolux E36EC75DSS Bedienungsanleitung

Electrolux

Electrolux RC36DE60PB Betriebsanleitung

Electrolux

Electrolux ECCG3668AS Bedienungsanleitung

Electrolux

Electrolux EW36IC60IB - 36" Induction Cooktop Handbuch

Electrolux

Electrolux FPIC3695MS Bedienungsanleitung

Electrolux

Electrolux EHC30001X Bedienungsanleitung

Electrolux

Electrolux Libero Line 601619 Bedienungsanleitung

Electrolux

Electrolux 5995447090E36GC76EPS Bedienungsanleitung

Electrolux

Electrolux EHGC93CI Bedienungsanleitung

Electrolux

Electrolux Induction/2 - EW30CC55GW 30" Hybrid Cooktop Bedienungsanleitung

Electrolux

Electrolux Electric cooktops Montageanleitung

Electrolux

Electrolux EW30IC60LS Bedienungsanleitung

Beliebte Kochfeld Handbücher anderer Marken

Bonnet

Bonnet OPTIMUM 700 Betriebsanleitung

Jenn-Air

Jenn-Air JGCP430 Bedienungsanleitung

Frigidaire

Frigidaire FES367FCC Kurzanleitung

Ztove

Ztove EZ2 DUO Bedienungsanleitung

Kleenmaid

Kleenmaid cooking GCTK9011 Installationsanleitung

Jenn-Air

Jenn-Air JGC2536EB00 Bedienungsanleitung

Waldorf

Waldorf RN8603E-B Bedienungsanleitung

Whirlpool

Whirlpool SMP658CNEIXL Bedienungsanleitung

Wolf

Wolf CI243C/B Bedienungsanleitung

Fulgor Milano

Fulgor Milano F5PGK305S1 Bedienungsanleitung

GE JP389 Bedienungsanleitung

Wells

Wells WV-2HFG Bedienungsanleitung

IKEA

IKEA Lagan HGA4K Bedienungsanleitung

Samsung

Samsung NA36N9755 Bedienungsanleitung

Miele

Miele KM 404 Bedienungsanleitung

Lacor

Lacor 69562 Technisches Datenblatt

Keating Of Chicago

Keating Of Chicago MG-2 Bedienungsanleitung

Jenn-Air

Jenn-Air CCE1400 Bedienungsanleitung