Electrolux EQAXF01BXWT Bedienungsanleitung
EQAXF01BXWT
USER MANUAL 1EN
Thank you for choosing ELECTROLUX. This manual contains
Welcome
Environmental Notice
1
all the information you need to safely and correctly use your water
dispenser. Please read all the instructions prior to using the appliance,
and keep this manual in a secure place for future reference. Do not
remove the rating plate label which attached adhesive identification label
containing the code, model number, manufacturer and other information.
This label will be used by an ELECTROLUX authorized service
representative in the event that your water dispenser needs service.
The packaging material used is recyclable. We
recommend that you separate plastic, paper and
cardboard and give them to recycling agents.
To help preserve the environment, the refrigerant
used in this product is R134a (Hydrofluorocarbon -
HFC), which does not affect the ozone layer and
has little impact on the greenhouse effect.
According to WEEE (Waste of Electrical and
Electronic Equipment) guidelines, waste from
electrical and electronic devices should be
collected separately. If you need to remove of this
appliance in the future, do not throw it away with
the rest of your domestic garbage. Instead, please
take the appliance to the nearest WEEE collecting
agents, where available.
12
10
Do not try to install or turn on the unit without having read the indicated
safety precautions in this manual.
The dispenser heats water to a temperature of 90°C. It can cause severe
scalding. Please operate it carefully.
In case of damage, please contact an authorized technical service agent.
Do not disassemble the electrical parts of this appliance. Any repairs done
by an unauthorized person may cause serious injuries or properties incident.
The adult should supervise the children in order to make sure the children can
not play with the appliance.
The appliance is not intended for use by persons(including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
This appliance is intended to be household used only.
If the power cord is damaged, it must be replaced by a special cord or assembly
available from the manufacturer or its service agent.
To avoid danger of suffocation, keep plastic bag away from babies and children.
Keep ventilation openings, in the appliance enclosure or in the built-in
structure, clear of obstruction.
Do not use mechanical devices or other means to accelerate the
defrosting process, other than those recommended by the manufacturer.
Water dispenser information .........................................................
Precautions .................................................................................
Illustration ...................................................................................
Using your water dispenser ...........................................................
Cleaning and maintenance .................................................................
Trouble Shooting .............................................................................
Circuit diagram ...............................................................................
Technical Information .......................................................................
Customer Care ...............................................................................
Operation instructions .......................................................................
Contents
Attention
4
3
6
7
8
13
13
14
2
5. Do not store explosive substances such as aerosol cans with a
flammable propellant in this appliance.
1. This unit is designed for drinkable water only. Put bottles as specified inside
2. This unit should be used in an environment with temperatures ranging from
10°C to 43°C with a relative humidity not higher than 90%.
the cabinet before using.
3. The dispenser can satisfy the need for hot water, cold water, room
temperature water and water as a mixture of the cold water and room
temperature water.
4. With the adoption of distinctive thermal isolation technology, this unit can
minimize thermal exchange between hot, room temperature and cold water.
The heating method of machine can be only used in the lower than 1500m
elevations.
6. Regional restrictions
Water dispenser information
3
7. To avoid any malfunction and keep your health better, please make sure you
are using purified water and don’t fill the water bottles directly from the tap.
Do not use an extension cord or
plug adaptor.(Fig.2)
Fig. 1
Fig. 2
1. Plug the water dispenser directly into the
socket. The unit requires proper
grounding and the correct voltage (as
technical information specified on page 13
of this manual).(Fig. 1)
2. An appropriate length of power-supply cord
3. Connect the plug firmly.
4.
is provided to reduce the risks of becoming
entangled in, or tripping over a longer cord.
6. Do not place the water dispenser sitting over the
power cord.
3. Recommend to install the anti-tilt bracket at the
1. Destroy the carton, plastic bag and other
2. Children require supervision when using the
back side of this water dispenser to prevent
dispenser.
packing materials after the dispenser is
unpacked. Children might use them for
play.
the dispenser from falling down which could
cause injury.(Fig. 6)
5. Choose a place that is near a grounded
electrical socket. Keep the dispenser at least
20cm away from walls and other appliances
and furniture on all 4 sides.
Precautions
For children
For the user/installer
4
8. Use the switch when turning the heating/
9. Do not fasten, twist or tie the power cord. if
7. Do not pull out or insert the plug with wet
cooling On/Off. Locate on the left back
hands to avoid electric shock.(Fig. 3)
side of water dispenser.(page 6)
the power cord is damaged, it should be
replaced by the manufacturer, service
technician or a qualified person to prevent
any risk.
10. Keep the unit in a dry place and away from
11. To avoid damage to the unit, do not plug the
direct sunlight. Do not place the machine on
paper or foam. Do not place anything
flammable beside this machine.(Fig. 4)
12. Unplug the unit when the unit will not be
used for a long period for the reason of
saving electricity.
14. Never use organic liquids polishing chemical
13. Never turn the unit upside down or tilt it
more than 45°.(Fig. 5)
to clean the machine.
15. The thermostat to control temperature has
been set up by There is nomanufacturer.
need to adjust it yourself.
Fig. 3
Fig. 4
Fig. 5
power cord or turn on the heating switch
until the water can flow out from the hot water
spout when the hot water button be activated.
5
button of cold water
button of hot water
(FRONT) (REAR)
button of normal water
panel
spout
front carapace
indicator light
drip tray
11
12
9
13
10
4
6
5
7
condenser
power cord
cooling switch
heating switch
drain hole
Illustration
6
8
13
near a grounded socket. Do not plug in power cord yet.
Fig. 6
Installing the floor Bracket kit(Fig.6)
Water dispenser
Bracket
Head
Collar
The hole for
tighten screw
1. Place dispenser upright.
2. Locate dispenser on a hard and level surface in a cool shaded location
at least 20 cm of clearance on both sides.
3. Position dispenser so the back is at least 20 cm from wall and there are
1. Snap drip tray and grid assembly into front carapace.
1. Use 13 mm screw to fix the fixing bracket on the
side of base pan.
2. Drill out a screw hole(6 mm) on the floor.
3. Insert a screw anchor (wall plug) into the drilled hole.
4. Move water dispenser, Align fixing bracket hole
with screw hole of the floor.
5. Put the 25mm screw into the screw hole of fixing
bracket.
6. Tighten the screw.
1 1 1 2-3
4-5 6
Fig. 7
1. Open cabinet door.
2. Place fresh bottle outside of cabinet.
3. Remove the entire plastic cap from top
of bottle.
4. Clean outside of new bottle with a cloth.
5. Place probe assembly into bottle.
6. Slide collar with head down until it clicks
in place.
7. Slide bottle into cabinet and close door.
Using your water dispenser
Locate dispenser
Assemble
Machine Installation
Install water bottle
7
Fig. 8
Plug cord into a properly grounded
socket.
At this time the pump will begin to
move water from the bottle to the hot
and cold tanks. It will take up to
approximate 5 minutes to fill the tanks
for the first time. During this period the
pump will run continuously. This is normal.
Fig. 9
Provide electricity
Activate heating and cooling
Light indicators
Dispensing water
Operation Instructions
8
This unit has been tested and sanitized
prior to packing and shipping. During
transit dust and odors can accumulate in
the tank and lines. Dispense and dispose
at least one liter of water to prior to
drinking any water.
This unit will not dispense hot or cold
water until the switches are activated.
To activate, push top side of power
switches in to start heating and cooling
water.
- If you do not want to heat water, push
bottom side of red switch in.
- If you do not want to cool water, push
bottom side of green switch in;
Lights up when water shortage.
Indicates that the water is being heated.
Indicates that the water is being chilled.
The indicator lights show that the device is
working correctly. After connecting the
device, check if the indicators are on.
Fig.10
Fig.11
After setup, it will take up to approximate
1 hour get water to maximum cold
temperature. During this time the
compressor could run continuously.
This is normal.
1. Position bottle, glass, pitcher or
cooking pot below spout.
2. Press cold water button
downward to start cold water flow.
3. Release button once desired fill
level is achieved.
1. Position bottle, glass, pitcher or
cooking pot below spout.
2. Press normal water button
downward to start normal water
flow.
3. Release button once desired fill
level is achieved.
Dispensing cold water
Dispensing normal water
After setup, hot water will be available
in 15-20 minutes.
1. Position bottle, glass, pitcher or
cooking pot below spout.
2. Push the red child lock button from
right to left and press hot water button
downward to start hot water flow.
3. Release button once desired fill
level is achieved.
Dispensing hot water
9
Inhaltsverzeichnis
Andere Electrolux Wasserspender Handbücher
Electrolux
Electrolux ED30S Bedienungsanleitung
Electrolux
Electrolux EQALF01TXSP Bedienungsanleitung
Electrolux
Electrolux 864015 Bedienungsanleitung
Electrolux
Electrolux EA11S Bedienungsanleitung
Electrolux
Electrolux EQACF01TXWI Bedienungsanleitung
Electrolux
Electrolux ES11S Bedienungsanleitung
Electrolux
Electrolux EQAXF1BXWG Bedienungsanleitung
Electrolux
Electrolux EQB20C2MMS Bedienungsanleitung
Electrolux
Electrolux 864026 Bedienungsanleitung
Electrolux
Electrolux EQALF01TXST Bedienungsanleitung
