Elid EL1335 Bedienungsanleitung
EL1335
ACCESS CONTROL PANEL
USER GUIDE
(Revision 1.1.11)
ELID SDN BHD
EL1335 Access Control Panel
User Guide
Revision 1.1.11
1
EL1335 ACCESS CONTROL PANEL
USER GUIDE
1.
SYSTEM INITIALIZATION……………………………………………………….
4
1.1 TO COLD START……………………………………………………………
4
1.2 TO PROGRAM THE MASTER CARD…………………………………….
5
1.3 SETTING CARD FORMAT …………………………………………………
5
1.4 TO USE USER CARDS’ PRESET OR USER-DEFINED PIN…………..
6
1.5 BEFORE OPERATION……………………………………………………..
7
2.
MAIN COMMANDS……………………………………………………………….
8
3.
SPECIAL CARD………………………………………………………………….
27
3.1 INTRODUCTION……………………………………………………………
27
3.2 REGISTERING SPECIAL CARDS………………………………………..
28
3.3 APPLY A SPECIAL CARD……………………………………………….
29
EL1335 Access Control Panel
User Guide
Revision 1.1.11
2
4.
PROGRAMMABLE PIN…………………………………………….……………
35
5.
SELF-TEST COMMANDS.………………………………………………………
38
6.
FIRMWARE UPDATE…………………………………………………………....
44
7.
DATA STORAGE CAPACITY………………………………………………..…
45
EL1335 Access Control Panel
User Guide
Revision 1.1.11
3
EL1335 ACCESS CONTROL PANEL
Keypad Layout
EL1335 Access Control Panel
User Guide
Revision 1.1.11
4
CHAPTER 1
1. SYSTEM INITIALIZATION
1.1 TO COLD START
Hold down keys "1" and "3" on the keypad and simultaneously switch off and then switch back
on the power supply. (Alternatively, hold down keys "1" and "3" on the keypad and press the reset
switch while power is on.)
Release the two keys 3 seconds after the power supply is switched back on. If the cold start has
been properly performed, the display will show "PIN". When the display shows "PIN", key in the
6-digit Cold Start PIN code (packed in an envelope in your EL1335 package, otherwise
‘123456’).
EL1335 Access Control Panel
User Guide
Revision 1.1.11
5
1.2 TO PROGRAM THE MASTER CARD
If the PIN code has been correctly entered, the display will change to "MAST". Now, key-in the 6-
digit card number of your Master Card.
1.3 SETTING CARD FORMAT
The display will now show "CT". Key in the card type according to following code:
Code
Meaning
Details
0
Reserved
1
Reserved
2
Wiegand 26 format
-
3
Wiegand HID format
-
4
Wiegand Free Format
For this format, you need to set offset, number of bits &
Max bits:
Co.<00> Set offset bit
ML.<00> Set No. of bit as card No./Card Size
CL.<00> Max No. of bit to take/length of card number for
reading
EL1335 Access Control Panel
User Guide
Revision 1.1.11
6
Limits of bit settings for Card Type 4 (Free Wiegand)
Limits
Symbol
No. of Bits
Max no. of bits to make up a card number
ML
40 (000000~999999)
Max bits to be taken for reading a card number
CL
20
Max offset bits to read a card number
Co
20
1.4 TO USE USER CARDS’ PRESET OR USER-DEFINED PIN
Display
What to do
PT.<N>
Key in the code according to your application
0 = To use preset PIN
1 = To use user-programmable PIN
The display will then immediately change to "db 1".
After a few seconds, the display will then show the current system time, in hours and minutes.
The controller has now been initialized.
EL1335 Access Control Panel
User Guide
Revision 1.1.11
7
1.5 BEFORE OPERATION
A "burn-in" operation should be performed on the new PCB for EL1335 (Revision 1.0) to ensure
the functionality of the backup battery.
EL1335 Access Control Panel
User Guide
Revision 1.1.11
8
CHAPTER 2
2. MAIN COMMANDS
Note: To access the programming menu, badge your Master Card at the EL1335 card reader.
Key Command
1 DATE/TIME/Daylight Saving Time
2 Timer
3 Category
4 Door Parameters (PLR/PIN MODE/NO ENTRY MODE)
5 Time Zones (ALR TZ/PIN DISABLE TZ/GP-TZ)
6 Holidays
7 ADD Cards by reader
8 Remove Cards by reader
9 Clear Memory
EL1335 Access Control Panel
User Guide
Revision 1.1.11
9
Shift + Key Command
0 SELF-TEST
1 PRINT
2 Unit Number/Baud Rate
3 Door/Contact Type/Lock Release Time/Keypad buzzer alarm
4 Select Output type / Sensor type / Set Anti pass back
5 Customer Code
6 Pin Only mode ( 20 sets )
7 ADD Cards by Keys
8 Remove Cards by keys
9 Setting Special Card Range
Note:
Shift Key Commands require you to press 0 (shift) first, follows by the command key. Eg.
Press 0 followed by 0 again to activate a self-test command, which is another digit (See Section
5).
Inhaltsverzeichnis
Andere Elid Bedienfeld Handbücher
