Elid EL2305D Bedienungsanleitung
EL2305D Access Control Panel
User Guide
Revision 1.1.20 0
EL2305D
DOOR ACCESS CONTROLLER
USER GUIDE
(Revision 1.1.20)
ELID SDN BHD
EL2305D Access Control Panel
User Guide
Revision 1.1.20
1
EL2305D DOOR ACCESS CONTOLLER
USER GUIDE
1. SYSTEM INITIALIZATION 4
1.1 TOCOLDSTART 4
1.2 TO PROGRAMTHE MASTER CARD 5
1.3 TOPROGRAMTHEENGINEERINGCARD 5
1.4 SETTING CARDTYPE 6
1.5 SETTINGDISPLAYTYPE 7
1.6 SETTINGEL2000MODE 8
1.7 SETTINGCONTINUOUS SWIPING 8
1.8 SETTINGCARD SIZE 9
1.9 SETTING CLEARSECURITY 10
1.10 BEFORE OPERATION 11
2. ENGINEERINGMENU 12
2.1 TOENTERENGINEERINGMENU 14
2.2 DOOR MENU 14
2.3 SENSOR MENU 22
2.4 OUTPUTMENU 26
2.5 COMMUNICATION MENU 29
EL2305D Access Control Panel
User Guide
Revision 1.1.20
2
2.6 TESTMENU 31
2.7 SAVE PARAMETER 36
2.8 CLEARMEMORY 36
3. USER MENU 37
3.1 TESTMENU 39
3.2 CARDMENU 43
3.3 TRANSACTIONMENU 49
3.4 DOORMENU 51
3.5 SENSORMENU 54
3.6 OUTPUTMENU 56
3.7 PINENTRY MENU 59
3.8 CLEARMEMORY 59
EL2305D Access Control Panel
User Guide
Revision 1.1.20
3
EL2305D DOOR ACCESS CONTROLLER
Programming Keypad Layout
EL2305D Access Control Panel
User Guide
Revision 1.1.20
4
CHAPTER 1
1. SYSTEM INITIALIZATION
1.1 TO COLD START
Hold down keys "A” on the keypad and simultaneously switch off and then switch back on the
power supply. (Alternatively, hold down keys "A” on the keypad and press the reset switch while
power is on.)
Release the keys 3 seconds after the power supply is switched back on. If the cold start has been
properly performed, the display will be shown as below:-
If you press <#> , the screen changes to :-
Mas Eng Crd Disp
Crd Crd Typ Typ
EL2305D Access Control Panel
User Guide
Revision 1.1.20
5
1.2 TO PROGRAM THE MASTER CARD
Press <A> key, in order to set the master card number.
You should key in 6-digit master card number followed by the <#> key.
1.3 TO PROGRAM THE ENGINEERING CARD
Press <B> key, in order to set the Engineering card number.
EL2k Con Crd clr
Mod Swip Siz sec
EL2305D SET-UP
Mast card 000000
EL2305D Access Control Panel
User Guide
Revision 1.1.20
6
You should key in 6-digit Engineering card number followed by the <#> key.
1.4 SETTING CARD TYPE
Press <C> key to choose the type of reader and card format you wish to use.
You can change the card type by pressing <D> key repeatedly.
EL2305D SET-UP
Eng card 000000
EL2305D SET-UP
Card Type WIEG
EL2305D Access Control Panel
User Guide
Revision 1.1.20
7
1.5 SETTING DISPLAY TYPE
Press <D> key to select “DISPLAY TYPE” command.
Code
Details
WIEG
Wiegand Reader, with 26-bit Wiegand format
PROX
Proximity Reader, with ELID format
EPRX
Diester Reader, with 48 bit Diester format
FWIE
Free Wiegand Reader, with 32bit format
PIN
MatrixPIN Keypad Reader only
EL2305D SET-UP
Disp Type ER5S
EL2305D Access Control Panel
User Guide
Revision 1.1.20
8
1.6 SETTING EL2000 MODE
Press <#> key from main screen and on the second screen of main menu press <A> to select
“EL2000 MODE” command.
YES 6 outputs will emulate EL2000, being used for duress alarm, door open alarm, door
shunt, sensor alarm and sensor armed.
NO These output are General purpose Outputs that can be programmed to operate when
certain input conditions occur.
1.7 SETTING CONTINUOUS SWIPING
Press <B> to select “CONTINUOUS SWIPING” command.
EL2000 Alrm Outp
Emulate NO
EL2305D Access Control Panel
User Guide
Revision 1.1.20
9
YES User are allowed to swipe even when the door is open.
NO The reading is disable until the door is closed.
1.8 SETTING CARD SIZE
Press <C> to select “CARD SIZE” command. This command is for setting the data capture
window of a Free Format. It is not applicable to Wiegand Format.
Card Swiping
Continuous NO
SET CARD SIZE
Ofs00 Ln06 Max 17
Andere Handbücher für EL2305D
1
Inhaltsverzeichnis
Andere Elid IP-Zugriffskontrollsysteme Handbücher
