Elinx EIR410-2SFP-T Bedienungsanleitung
Manual Documentation Number EIR410-2SFP-T– 0109m
www.bb-elec.com
www.bb-europe.com
E
EI
IR
R4
41
10
0-
-2
2S
SF
FP
P-
-T
T
U
Us
se
er
r
M
Ma
an
nu
ua
al
l
i Manual Documentation Number EIR410-2SFP-T – 0109m
www.bb-elec.com
www.bb-europe.com
E
EI
IR
R4
41
10
0-
-2
2S
SF
FP
P-
-T
T
D
Do
oc
cu
um
me
en
nt
ta
at
ti
io
on
n
N
Nu
um
mb
be
er
r:
:
E
EI
IR
R4
41
10
0-
-2
2S
SF
FP
P-
-T
T-
-
0
01
10
09
9m
m
U
Us
si
in
ng
g
d
do
om
me
es
st
ti
ic
c
a
an
nd
d
i
im
mp
po
or
rt
te
ed
d
p
pa
ar
rt
ts
s
b
by
y
International
Headquarters
International Headquarters
B&B Electronics Mfg. Co. Inc.
707 Dayton Road
Ottawa, IL 61350 USA
Phone (815) 433-5100 -- General Fax (815) 433-5105
Website: www.bb-elec.com
European Headquarters
B&B Electronics Ltd.
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone +353 91-792444 -- Fax +353 91-792445
Website: www.bb-europe.com
©2008 B& B Electronics Mfg. Co. Inc. No part of this publication may be reproduced or transmitted in any
form or by any means, electronic or mechanical, including photography, recording, or any information
storage and retrieval system without written consent. Information in this manual is subject to change
without notice, and does not represent a commitment on the part of B&B Electronics Mfg. Co. Inc.
B&B Electronics Mfg. Co. Inc. shall not be liable for incidental or consequential damages resulting from
the furnishing, performance, or use of this manual.
All Brand names used in this manual are the registered trademarks of their respective owners. The use of trademarks or other
designations in this publication is for reference purposes only and does not constitute an endorsement by the trademark holder
Table of Contents
Table of Contents
1. Introduction................................................................................................................................1
Features.........................................................................................................................1
Package List..................................................................................................................2
2. Hardware Description................................................................................................................3
Physical Dimension.......................................................................................................3
Front Panel....................................................................................................................3
Top View........................................................................................................................4
LED Indicators...............................................................................................................5
Ports ..............................................................................................................................6
Cabling.........................................................................................................................10
Wiring the Power Inputs ..............................................................................................11
Wiring the Fault Alarm Contact....................................................................................12
3. Mounting Installation...............................................................................................................13
DIN-Rail Mounting .......................................................................................................13
Wall or Panel Mount Plate Mounting...........................................................................15
4. Hardware Installation ..............................................................................................................16
Installation Steps.........................................................................................................16
5. Network Application................................................................................................................17
6. Troubleshooting.......................................................................................................................18
7. Technical Specification...........................................................................................................19
ii Manual Documentation Number EIR410-2SFP-T – 0109m
www.bb-elec.com
www.bb-europe.com
Introduction
Introduction
The EIR410-2SFP-T is an industrial DIN mount, unmanaged 10 port Ethernet switch with
Gigabit capability. It has (8) 10/100 copper Ethernet ports and (2) Gigabit Combo ports
that support copper or SFP module connections.
Features
•System Interface/Performance
oRJ-45 port support Auto MDI/MDI-X Function
oSFP (Mini-GBIC) supports 100/1000 Dual Mode
oStore-and-Forward Switching Architecture
oBack-plane (Switching Fabric): 5.6Gbps
o1Mbits Packet Buffer
o8K MAC Address Table
oSupports Wide Operating Temperature of -40 to 75oC
•Power Supply
oWide-range Redundant Power Design
oPower Reverse Polarity Protected
oOverload Current Removable Fuse Present
•Case/Installation
oIP-30 Protection
oDIN Rail and Wall Mount Design
•Provides surge protection 3,000 VDC for power line
•Supports 6,000 VDC Ethernet ESD protection
1Manual Documentation Number EIR410-2SFP-T – 0109m
www.bb-elec.com
www.bb-europe.com
Introduction
2 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
Package List
•(1) EIR410-2SFP-T, 10 Port Gigabit Industrial Ethernet Switch
•(1) Quick Start Guide
•(1) CD ROM with User Manual
•(2) Wall Mounting Bracket and Screws
Hardware Description
Hardware Description
Physical Dimension
(W x D x H) is 72mm x 105mm x 152mm (2.8 x 4.1 x 6.0 inches)
Front Panel
The Front Panel of the EIR410-2SFP-T is shown below.
3Manual Documentation Number EIR410-2SFP-T – 0109m
www.bb-elec.com
www.bb-europe.com
Hardware Description
4 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
Top View
The top panel view of the EIR410-2SFP-T is equipped with one terminal block connector
that consists of two 12 to 48 VDC power inputs and the fault alarm output.
T
Hardware Description
5 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
LED Indicators
LED Status Meaning
Green Power 1 is active
PWR1 Off No power at input 1
Green Power 2 is active
PWR2 Off No power at input 2
Red Power 1 or Power 2 is
inactive
Fault
Off
Power 1 and 2 are both
functional, or no power is
applied
Green Connected to network
Blinks Networking is active
P9, P10
(10/100/1000T,Upper LED)
Off Not connected to network
Green The port is operating at
speed of 1000M
P9, P10
(10/100/1000T, Lower LED) Off
The port is disconnected or
operating at speed of
10/100M
Green SFP port is linking
Blinks Data is transmitting or
receiving
Link/Active
(P9, P10 SFP)
Off Not connected to network
P1 to P8 On Connected to network
Hardware Description
6 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
Blinks Networking is active
(Green LED)
Off Not connected to network
On Full duplex operation
Blinks Collision of packets occurs
P1 to P8
(Yellow LED) Off Half duplex operation or not
connected to network
Ports
•RJ-45 ports
•RJ-45 ports: Eight RJ-45 ports auto-sense for 10, 100 Mbps while two ports auto-sense
for 10, 100 or 1000 Mbps device connections. The auto MDI/MDIX feature allows
connections to switches, workstation and other equipment without changing straight
through or crossover cabling. The charts below show the cable pin assignments for
straight through and crossover cables.
•RJ-45 Pin Assignments
Pin Number Assignment
1 Tx+
2 Tx-
3 Rx+
6 Rx-
Note “+” and “-” signs represent the polarity of each wire pair.
All copper ports on the EIR410-2SFP-T support automatic MDI/MDI-X operation, you can
use straight-through cables (See Figure below) for all network connections to PCs or servers,
Hardware Description
7 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
or to other switches or hubs. In straight-through cables, pins 1, 2, 3, and 6, at one end of the
cable, are connected straight through to pins 1, 2, 3 and 6 at the other end of the cable. The
table below shows the 10BASE-T / 100BASE-TX MDI and MDI-X port pin outs.
Pin MDI-X Signal Name MDI Signal Name
1 Receive Data plus (RD+) Transmit Data plus (TD+)
2 Receive Data minus (RD-) Transmit Data minus (TD-)
3 Transmit Data plus (TD+) Receive Data plus (RD+)
6 Transmit Data minus (TD-) Receive Data minus (RD-)
Straight Through Cable Schematic
Cross Over Cable Schematic
•2 Gigabit Copper/SFP (mini-GBIC) combo ports:
The EIR410-2SFP-T has two auto-detect Giga ports—copper/Fiber combo ports. The
Gigabit Copper (10/100/1000T) ports should use Category 5e or above UTP/STP cable for
connection. The SFP slots support dual mode which can switch the connection speed
between 100 and 1000Mbps. These SFP slots can be used to connect the network segment
with single or multi-mode fiber. You must choose appropriate mini-GBIC module to plug
into the slots. Make sure the module is aligned correctly and then slide the module into the
Inhaltsverzeichnis
Andere Elinx Netzwerk-Router Handbücher
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise