Elite Screens TE200HR2 Bedienungsanleitung

Rev.053117 DR 1 www.elitescreens.com

Electric Motorized Tab-Tensioned Rear Projection Screen

CineTension Plus Series

User’s Guide

Important Safety & Warning Precautions

Make sure to read this user’s guide and follow the procedures below.

Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra

Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.

Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this

unit are prohibited and will void your warranty. For more information, please contact our Technical Support

Department at (877) 511-1211 Ext. 604.

•Please retain this user’s guide for future reference.

•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the

manufacturer.

•Handle the unit carefully during transportation to avoid any damages.

•To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

•The power outlet supplying power to the unit should be close to the unit and easily accessible.

•Do not install the unit on uneven or inclined surfaces.

•Do not put heavy objects on the power cord and position it properly to avoid creating a trip

obstacle.

•Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short

circuit.

•There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself.

No one except authorized technicians can open and make repairs to this unit.

•Make sure the power source this unit is connected to has a continuous power flow.

•If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to

avoid overheat.

•Do not handle the power plug when your hands are wet or your feet are in contact with water.

Do not use this unit under the following circumstances.

•Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.

•Avoid direct Sunshine, rain shower and moisture.

•Keep away from fire sources and high temperature to prevent this device from overheating.

•Cut off the power supply first before transportation or maintenance.

•Fully disconnect from the power supply when the unit is not in use for a long period of time, as

should be done with any other electric household appliance.

•To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is

obvious damage or if there are any evident broken parts.

Rev.053117 DR 2 www.elitescreens.com

WARNING

The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black

drop in the roller. Please be aware of this as it will void the limitation of your warranty.

Individual modifications to this product are prohibited and will void the warranty with the manufacturer.

Please contact Elite Screens Customer Service for any questions.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur on a particular installation. If this

equipment causes harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures.

Reorient or relocate the receiving antenna of the device which may be causing the

interference.

Increase the separation between the screen and the device’s receiver.

Connect the equipment into a different power outlet other than the device.

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign

particles such as dust, sawdust, and/or liquids.

NOTE

Regardless of the mounting method, the screen should be securely supported so that the vibration or

pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure

that the fasteners used are of adequate strength and suitable for the installation location.

Hardware Parts List

Please make sure all parts listed below are included before proceeding with the installation.

A.M10*Suspended Hook x 4 pcs

B. 20cm*Bubble leveler x1pc

Rev.053117 DR 3 www.elitescreens.com

Clockwise

rotation

Installation Instructions

Recessed Installation

1. Select the installation location for your screen. Measure the distances between each eye bolt (Shown as

measurements L and A in Fig.1). Mark the installation area on the ceiling based on the measurements

taken. Using the marks as a guideline, drill a hole in the ceiling for each suspension bolt. The distance

between the installation hole (M) and the wall should be no longer than the measurement A. Insert one

eye bolt of the M10 Suspended hooks into the predrilled holes.

2. Connect the center component of the M10 Suspended hooks to the eye bolts installed above the ceiling.

Once properly secure, connect the third component of the M10 Suspended hooks. Attach the suspended

hooks(4xM10) individually to each of the 4 eye bolts located on the top of the screen (A/B/C/D) .

3. After the installation is complete, if the screen is not leveled, you can adjust the height of the suspended

hooks to level the screen. Below are the adjustment methods for the suspended hooks.The maximum

and minimum adjustable lengths are shown in Fig 3.

①②③④

Hole

（

Fig.3

）

（

Fig.1

）

Ceiling

Wall

Suspended hook

Counter-

clockwise

rotation

（

Fig.2

）

The Screen

Rev.053117 DR 4 www.elitescreens.com

CineTension Plus Series | Controls and Accessories

A. IR Remote

B. RF Remote

C. Wall switch control box

D. 5-12 volt trigger cable

E. IR extended “eye” receiver

F. Wireless 5-12v trigger cable

G. AAA batteries

Screen operation

Electric Current: Depending upon region, your Elite Screen will operate on 110v, or 220v voltage.

1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.

2. Once the screen’s has power, you’ll be able to control it using any of the 6 methods described below.

6 ways to control your CineTension Plus

1. IR remote control (Item A, Fig 1) and IR “Eye” Receiver (Item E, Fig 2):

The Infrared functions by direct line of sight contact with a beam range of 30

feet. The IR “Eye” receiver plugs directly into the screen’s RJ-45 input to

present a low profile line-of-sight control option for your IR remote control

even in a recessed ceiling installation. Once connected, simply aim the IR

remote at the IR “Eye” receiver to control the screen.

2. RF Remote Control (Item B): The radio waves eliminate the need for a

direct line of sight with a range of 100 feet.

Fig.2

STOP

DOWN

IR “eye” receiver

Fig.1

IR/RF remote

3. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch

is a wall mount control box with an up/stop/down button and

plugs directly into the screen’s RJ-45 input.

Fig.3

3 Way Wall Switch

(does not have IR sensor)

Rev.053117 DR 5 www.elitescreens.com

Stop

Down

4. 5-12 volt trigger (Item D, Fig 4):The built-in 5-

12V trigger input allows your screen to synchronize

its drop & rise with the projector’s power cycle.

The screen deploys when the projector powers on

and will retract when the projector powers off. The

5-12 volt RJ45 cable connects to your projector’s

trigger output via a separate cable that may or may

not be provided by the manufacturer of the

projector. The trigger feature will not work without

an output cable from the projector, but it can be

tested by connecting the Red (+) and Green (-)

cable to a 9-volt battery.

5. Wireless 5-12 volt trigger (Item F, Fig 5): The RF remote control serves as a dual purpose, independently as a

handheld remote control, or in conjunction with the Wireless 5-12 volt trigger cable. The radio frequency

technology can be programmed to send a wireless signal to synchronize its drop & rise with the projector’s power

cycle.

Here’s how to set up your Wireless 5-12 volt trigger | Synchronization Instructions

Step1: Connect the wireless 5-12 volt trigger cable to the RF remote (3.5mm)

Step 2: Connect the 12 v adaptor end of the wireless 5-12 volt trigger cable to your projector

Step 3: Make sure to unplug your screen from the power outlet

Step 4: Hold the UP button on your RF remote

Step 5: While holding the UP button, plug the screen back to the power outlet

Step 6: Wait 5 seconds and then release the UP button

Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and able to

control your screen with your projector’s power cycle

Repeat the steps again if not successful.

(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-30

seconds for full off and on cycle each time)

DC 5-12V out

Wireless 5-12V

trigger cable

The back of the

projector

Fig 5

3 prong power cord

RJ45 Input

5-12 volt trigger cable

Fig.4

Rev.053117 DR 6 www.elitescreens.com

Dimensions Table

Model

Number A A1 A2 A3 A4 A5 B B1 B2 B3 B4 B5 C C1 C2 C3 C4

Unit: Inches

TE200HR2 204.0 197.2 192.0 174.3 8.9 196.0 112.3 6.7 4.0 98.1 3.5 105.6 6.7

8.7-

11.2 1.0 0.8 2.6

Unit: mm

TE200HR2 5182 5009 4878 4428 225 4978 2853 170 102 2491 90 2683 170 220-

285 25 20 67

For local EliteProAV contact or Technical Support, please visit

www.eliteproav.com

Note: Data Error: ±1"

Inhaltsverzeichnis

Andere Elite Screens Projektionsfläche Handbücher

Elite Screens

Elite Screens YardMaster 2 Series Bedienungsanleitung

Elite Screens

Elite Screens Sable Frame CineGrey 3D Bedienungsanleitung

Elite Screens

Elite Screens C Bedienungsanleitung

Elite Screens

Elite Screens Starling Tab-Tension Series Bedienungsanleitung

Elite Screens

Elite Screens Insta-RP Screen Series Bedienungsanleitung

Elite Screens

Elite Screens WhiteBoardScreen Universal Series Bedienungsanleitung

Elite Screens

Elite Screens Kestrel Stage Series Bedienungsanleitung

Elite Screens

Elite Screens TE100HC2 Bedienungsanleitung

Elite Screens

Elite Screens Evanesce B Series Bedienungsanleitung

Elite Screens

Elite Screens AEON series Bedienungsanleitung

Elite Screens

Elite Screens F100NWH Bedienungsanleitung

Elite Screens

Elite Screens TE100HC2 Bedienungsanleitung

Elite Screens

Elite Screens Manual SRM Pro Series Bedienungsanleitung

Elite Screens

Elite Screens WhiteBoardScreen Series Bedienungsanleitung

Elite Screens

Elite Screens Manual Series Bedienungsanleitung

Elite Screens

Elite Screens Saker Tab-Tension Series Bedienungsanleitung

Elite Screens

Elite Screens VMAX PLUS 4 SERIES Bedienungsanleitung

Elite Screens

Elite Screens CineTension 2 Series Bedienungsanleitung

Elite Screens

Elite Screens Pop-Up Cinema Series Bedienungsanleitung

Elite Screens

Elite Screens TE100HC2 Handbuch

Elite Screens

Elite Screens Kestrel Series Kurzanleitung

Elite Screens

Elite Screens WhiteBoardScreen Series Bedienungsanleitung

Elite Screens

Elite Screens Aeon CineGrey 3D AT Series Bedienungsanleitung

Elite Screens

Elite Screens CineTension2 Series Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch

SI Dynamic 2 XL Bedienungsanleitung

Draper

Draper Nocturne+ E Montageanleitung