Elite Screens AEON series Bedienungsanleitung

Rev.04/17/2017 DR www.elitescreens.com 1

Aeon Series

EDGE FREE® Fixed Frame Projection Screen

User’s Guide

Applies to all available screen materials: CineGrey 3D® EDGE FREE®and CineWhite® EDGE FREE®

Product Description: The Aeon Series is a fixed frame projection screen that uses Elite’s EDGE FREE® technology.

The EDGE FREE®design resembles a giant size flat panel TV display. The Aeon includes an ultra-thin trim as an

installation option to further enhance the frame appearance and absorb projector overshoot.An optional LED

backlighting kit is available for added visual appearance.

Hardware and Parts List

Please make sure all parts listed below are included before installation.

A. Elbow joint x4 pcs B. Top/Bottom horizontal

fame x4 pcs

C. Left/Right vertical

frame x2 pcs

D. Center joints x2 pcs

E. Center Support bar x1-3 pcs F. Wall brackets x2-3 pcs G. M5x15 screw x24 pcs H. M5x50 screws and

anchor x6 pcs

(135”-150”x2pcs;

180”-200” x3pcs)

I. Rubber hammer x1 pc

. Screwdriver x1 pc K. Black Tape x1 bag L. Bezel trim x6 pcs

M. Corner Support Bar

(180”-200”) x4 pcs

N. Corner sleeve x4 pcs

Rev.04/17/2017 DR www.elitescreens.com 2

Frame Assembly

1. Insert the center joint into one of the ½ horizontal frames (B) and fasten it with the two M5x15 screws (G).

2. Insert the other ½ horizontal frame piece to the center joint and fasten also using two M5x15 screws.

3. Repeat steps 1 and 2 for assembling the second horizontal frame.

Push

4. Insert the elbow joint (A) into each end of the horizontal frames (B) as shown below.

5. Insert the two vertical short frames (C) into the elbow joint (A).

Horizontal long frame (B)

Vertical short frame (C)

Horizontal long frame (B)

Elbow Joint (A)

push

Elbow Joint (A)

Horizontal frame

Center Joints

Top right Frame Top left Frame

Push

Rev.04/17/2017 DR www.elitescreens.com 3

6. Join the remaining horizontal long frame (B) with the frame built in the previous steps as shown below.

7. Make sure all four corners are properly in place to form a perfect square. Then fasten the four angles with the

M5x15 Screws (G).

Horizontal Long frame (B)

Four corners join correctly to form a perfect

square. Use the included screwdriver (J)to

fasten the M5x15 screws (G)into each

corner by aligning the frame screw holes to

the holes in the elbow joint (A).

push

Rev.04/17/2017 DR www.elitescreens.com 4

Screen Material Installation

1. Lay the screen material completely flat with the front facing down on a clean surface in a horizontal position. The

back side of the screen material should be placed upwards.

Note: The back side of the material has the velcro borders all around the edges.

2. Carefully and gently place the assembled frame on top the screen material as shown below. Make sure to not allow

the angle edge of the frame to come in direct contact with the screen material to avoid puncturing it.

3. After all of the corners of the frame have been properly aligned, attach the material to the frame in the following

order A→B→C→D (see instructions below for details).

Screen material back facing up

C A

Screen material comer

Rev.04/17/2017 DR www.elitescreens.com 5

Attach the screen material to the corners as shown below.

4. After all four corners have been attached; please check whether the frame corners are wrapped by the screen

material. If not, please loosen the velcro connection and repeat the above steps so the frame is not exposed.

5. Proceed to attach the rest of the material to the frame as described in the illustrations below.

Note: The black shaded part represents the velcro on the frame. That Velcro

end will ultimately attach with the other velcro end on the screen material.

Note:

Represents the

screen material

Lay the Velcro end on the screen

material over the Velcro end of the

frame and keep it within the edge.

Proceed in the following sequence

below

①②

2) Fold over and attach

material to the velcro

strip of the frame.

3) Fold over second side

and attach to frame

4) Repeat until all four

sides are done in the

order A, B, C, D

1) Stretch the screen

material in the direction

of the arrowhead.

Grasp the middle of the screen

material and attach it to the velcro

strip on the frame

Rev.04/17/2017 DR www.elitescreens.com 6

6. If the material is too loose or tight after adjusting all four corner sides, then you will need to reattach the material.

Please follow the steps below to properly remove the screen material from the frame. This procedure will ensure

prolonging the life of the screen material.

Screen Material Removal

1. Detach the velcro from the frame.

2. Gently pull back the material to release it from the velcro connections on the corners

Pull back the screen material from

the velcro connection along the

edges of the frame to detach it.

The key is to attach within the

middle sections of 1 and 2. Then

continue attaching the remaining

unattached areas.

Repeat the same steps on

remaining three sides in the

sequence A, B, C, and then D as

show below.

Attach in the following sequence: a-b-c-d

Rev.04/17/2017 DR www.elitescreens.com 7

Support bar installation (for models under 135”):

1. Position the center support bar (E)in the middle of the frame and align the hole on each end of the support bar

with the M6 hex screws on the top and bottom frames. Then fasten with the M6x12 screws.

Support bar installation (for models 135”- 150"):

1. Position the center support bar (E) and M6 hex screws in the areas of the frame shown in fig 1. (Each about one

thirds the way in from the end of the frame.) Align the hole on each end of the support bar with the M6 hex screws

located at the top and bottom frame

sections. Then fasten with the M6x12

screws.

Move the

M6 hex screw

to the middle area of the frames.

Align the M6 screws

with the two holes.

Center Support bar

Center Support Bar

Move the M6 hex screw to these areas of the frame.

Rev.04/17/2017 DR www.elitescreens.com 8

Support bar installation (for models 180”- 200")

2. Position the center support bar (E) and M6 hex screws in the areas of the frame shown in fig 1. Align the hole on

each end of the support bar with the M6 hex screws located at the top and bottom frame sections. Then fasten with

the M6x12 screws.

1. Position the Corner support bars (M) and M6 Hex screws in the areas of the frame as shown below in fig

2. Align the holes on each end of the corner support bars with the M6 hex screws located on the vertical

and horizontal frame sections. Then fasten with the M6x12 screws.

Align the M6 Screws with

the two holes located on

the Center Support Bar.

Figure 1

Center Support Bar

Align the M6 Screws with

the two holes located on

the Center Support Bar.

Figure 1

Move the M6 hex screw to these areas of the frame.

Rev.04/17/2017 DR www.elitescreens.com 9

Notice to Installer:

Please use the following installation instructions to obtain superior optical performance from the CineGrey 3D®

Angular Reflective ALR (Ambient Light Rejecting) Screen.

Make sure to follow these instructions in order for the CineGrey 3D® to perform correctly.

•Angular-Reflective material is not compatible with ultra/short-throw projectors

•Minimum lens throw ratio 1.5x image width

•Ambient light must not come from the same direction as the projector

Since angular-reflective means that the projected image will reflect at the mirror-opposite angle, it

is important to position the projector so that the viewer will get the best possible image.

Step 1: Establish the general “eye level” of the viewers

Step 2: Set the appropriate projection level

Step 3: Adjust the screen height level and projection angle

Input Angle (A) = Output Angle (B) aligns with the viewer’s angle

Figure 2

Corner Support Bar

Align the M6

screws with

the two holes

on the Corner

Support Bars.

Rev.04/17/2017 DR www.elitescreens.com 10

Edge trim Installation

Included is an ultra-thin black edge trim that provides an elegant bezel finish

1. Place the assembled frame on a flat and clean surface. The projection screen surface should be facing up.

a. As an option, Black Tape is supplied to cover any possible gaps between the pieces of the bezel trim. Align

the tape with the edge of the screen, as shown in Figure 1. Once properly aligned, apply the black tape to

the center of the top and bottom of the screen material.

Figure 1

Edge trim x 6 PCS

Black tape x1pcs

Screen Material

The black tape

Plastic corner sleeve x4pcs

The black tape

Andere Handbücher für AEON series

Inhaltsverzeichnis

Andere Elite Screens Projektionsfläche Handbücher

Elite Screens

Elite Screens OMS90H2 Bedienungsanleitung

Elite Screens

Elite Screens VMAX2 (Plus) Series Bedienungsanleitung

Elite Screens

Elite Screens VMAX 2 Series Bedienungsanleitung

Elite Screens

Elite Screens QuickStand Series Kurzanleitung

Elite Screens

Elite Screens F100XWH1 Bedienungsanleitung

Elite Screens

Elite Screens SILVERMAX106H2 Bedienungsanleitung

Elite Screens

Elite Screens Evanesce B Series Bedienungsanleitung

Elite Screens

Elite Screens DIY Screen Series Bedienungsanleitung

Elite Screens

Elite Screens CineTension2 Series Kurzanleitung

Elite Screens

Elite Screens Manual SRM Pro Series Bedienungsanleitung

Elite Screens

Elite Screens GolfSim Portable Series Bedienungsanleitung

Elite Screens

Elite Screens Aeon CineGrey 3D AT Series Bedienungsanleitung

Elite Screens

Elite Screens Manual Series Bedienungsanleitung

Elite Screens

Elite Screens YARD MASTER MANUAL SERIES Bedienungsanleitung

Elite Screens

Elite Screens AR2 Series Bedienungsanleitung

Elite Screens

Elite Screens Kestrel Series Kurzanleitung

Elite Screens

Elite Screens C Bedienungsanleitung

Elite Screens

Elite Screens EDGE FREE Aeon CineWhite UHD 2 Series Bedienungsanleitung

Elite Screens

Elite Screens Home100IWH2-A Handbuch

Elite Screens

Elite Screens TE100HC2 Betriebsanleitung

Elite Screens

Elite Screens Reflexion Series Bedienungsanleitung

Elite Screens

Elite Screens TE100HC2 Bedienungsanleitung

Elite Screens

Elite Screens TE100HC2 Bedienungsanleitung

Elite Screens

Elite Screens AEON series Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch

SI Dynamic 2 XL Bedienungsanleitung

Draper

Draper Nocturne+ E Montageanleitung