Elmdene G1380 BMU Series Bedienungsanleitung

13.8V

WITCH

ODE

OWER

UPPLY

ODULE

ITH

ATTERY

ONITORING AND

E OTE

AULT

IGNALLING

Models:

G1380xBMU

Where ‘x’ is max load current: 1A or 2A

EATURES

High efficiency cost effective power supply range ideal for use in Intruder, Access Control and General

Security applications. Featuring a regulated 13.8V dc output supplying continuous full rated current to load

and a universal mains voltage input. aximum battery life is assured using deep discharge protection to

prevent premature battery failure when operating in standby mode for extended periods. Two sets of volt

free contacts are provided to signal (i) loss of mains and (ii) battery and loss of output faults.

•Continuous full rated current to load

•Universal mains input voltage 90-264V ac

•High efficiency electronics for reduced

running costs and lower operating

temperatures

•Installer safe design with all high voltage

electronics fully shrouded

•ains transient protection circuit

•Lid and removal from wall tamper detection

•Green ains present LED

•Available in unboxed (module only) format

•Red Fault diagnostic LED

•Volt free contact signalling mains failure (EPS)

•Volt free contact signalling output and battery

faults (GEN)

•Full electronic short circuit and overload

protection on load output under mains

operation

•Individual battery and output fuse protection

PECI ICATION

Input Specification

Voltage (rated) 100-240V ac

Voltage (operating) 90-264V ac

Frequency 50-60Hz

ax Current See odel Specification Table

ains Input Fuse See odel Specification Table

Output Specification

Voltage 12.8 – 14.2V dc (13.8V dc nominal) on mains power

9.8 – 13.0V dc on battery standby

ax load current See odel Specification Table

Ripple < 400 mV pk-pk max

Load output Fuse See odel Specification Table below

Overload Electronic shutdown until overload or short circuit removed

(under mains power only)

Elmdene International Ltd

Tel: +44 (0)23 9269 6638

3 Keel Close, Interchange Park, Fax: +44 (0)23 9266 0483

Portsmouth,

Hampshire

PO3 5QD

, UK



Web:

www.elmdene.co.uk

Mechanical

Product Reference G13801BMU G13802BMU

Dimensions w x h x d (mm) 106 x 52 x 152

Environmental

Temperature -10 to +40°C (operating) 75% RH non-condensing

-20 to +80°C (storage)

Standby Battery

Battery Type 12V Valve Regulated Lead Acid

Battery Charging Fuse protection F1.0A 20mm Glass (G13801B U)

F2.0A 20mm Glass (G13802B U)

Model Specification Table

G13801BM G13802BM

Max Output Current to load 1A 2A

Output use (20mm glass) F1.0A F2.0A

Max Mains Input Current < 1.0A @ Full load < 1.0A @ Full load

Mains Input use (20mm 250Vac HBC) T2.0A T2.0A

Battery use Protection F1.0A F2.0 A

IGNALLING

UTPUTS

Rating: 0.10A @ 60Vdc 16Ω solid state relay contacts, volt free.

EPS Fault: Open if Loss of mains for >8s

GEN Fault: Open if Battery terminal voltage < 11.5Vdc (when operating in standby

with no mains present), battery not present or Output and/or battery

fuse blown

ault Diagnostic Table:

Red LED

( ault)

Green LED

(Mains) PSU Status

OFF ON Normal: Battery fully charged

One short flash

every second ON Normal: Battery charging but not fully charged

Flashing:

1second On

1 second Off

ON Fault: Output fuse or battery fuse blown, or battery missing

OFF Fault: No mains, output fuse blown

One short flash

every 3 seconds OFF Fault: No mains, battery supplying load.

OFF OFF Fault: No mains, No output, Batteries disconnected or completely

discharged

ONNECTIONS

O/P +, - Connection to equipment to be powered (Observe polarity)

EPS Fault: Relay output for mains fail. Open if loss of mains.

GEN Fault: Relay output for General Fault. Open in fault condition

BATT +, - Connection to standby battery. Use cables provided (Observe polarity)

L E N

0m m

20mm

NSTALLATION

NSTRUCTIONS

This unit is only suitable for installation as permanently connected equipment. This PSU is NOT SUITABLE for external

installation. This unit must be fed from a mains power source having a separate (approved) disconnect device and fitted

with a fuse or other over-current protection device rated at 3A maximum. Ensure that the disconnect device used has

appropriate earth fault protection to the applicable standard. EQUIPMENT MUST BE EARTHED. Before installation,

ensure that external disconnect device is OFF.The PSU should be installed according to all relevant safety regulations

applicable to the application

Mounting

1) ount securely in correct orientation allowing minimum clearance – see

Fig. 1.0

2) Route mains and low voltage output cables via different knockouts

and/or cable entry holes.

Use bushes and cable glands rated to UL94 HB minimum.

Mains Power Up

4) Attach correctly rated mains cable (minimum 0.5mm

[3A], 300/500Vac). Fasten with cable ties.

5) Apply mains power.

Check for 13.8Vdc on load outputs.

Check Green ains LED is ON.

6) Disconnect mains power.

Load Output

7) Attach correctly rated load cable and fasten using cable ties. Note polarity.

8) Apply mains power.

Check Green ains LED is ON.

NOTE: Red Fault LED may flash to indicate no battery has been connected, this is normal.

Verify load is operating correctly.

9) Disconnect mains power.

Signalling

10) Connect EPS and GEN fault outputs to appropriate inputs of Control and Indicating Equipment (CIE).

Standby Battery

11) Attach battery cables to terminal block and batteries.

NOTE: ensure correct polarity of battery connections: +ve use Red lead, -ve use Black lead.

Fig 1.0 Mounting of Module

PERATING

NSTRUCTIONS

In the event of loss of mains, a battery fault or a GEN fault, the corresponding Fault signal contacts will open (see Fault

diagnostic table for LED indicator status).

If the output of the PSU fails, the cause of the failure should be investigated e.g. short circuit load, connection of a

deeply discharged battery. The fault should be rectified before restoring power to the PSU. If any of the fuses require

replacing, ensure the correct fuse rating and type is used.

AINTENANCE

This unit is intended for use by Service Personnel only. There are NO USER SERVICEABLE parts inside.

There is no regular maintenance required of the PSU other than periodic testing, and replacement of the standby

battery. Reference should be made to the battery manufacturer's documentation to determine typical/expected

battery life with a iew to periodic replacement of the battery.

OMPLIANCE

This power supply unit meets the essential requirements of the following European Directives:

Low Voltage: 2014/35/EU E C: 2014/30/EU

WEEE: 2012/19/EU RoHs2: 2011/65/EU

ISPOSAL O

RODUCT AT

ND O

I E

This product falls within the scope of EU Directives 2012/19/EU Waste Electrical and Electronic Equipment (WEEE) and

2013/56/EU (Battery). At the end of life, the product must be separated from the domestic waste stream and disposed

via an appropriate approved WEEE disposal route in accordance with all national and local regulations.

Before disposal of the product, any batteries must be removed, and disposed separately via an appropriate approved

battery disposal route in accordance with all national and local regulations. Package used batteries safely for onward

transport to your supplier, collection point or disposal facility.

Caution: Risk of fire or explosion

if bare battery wires are allowed to touch.

See Specification for battery type information. The battery is marked with the crossed out wheelie bin

symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For more information ee: www.recyclethi .info

The packaging upplied with thi product may be recycled.

Plea e di po e of packaging accordingly.

Dieses Handbuch passt für folgende Modelle

Andere Elmdene Stromversorgung Handbücher

Elmdene

Elmdene STX2401-MOD Bedienungsanleitung

Elmdene

Elmdene STX2402-MOD Bedienungsanleitung

Elmdene

Elmdene STX2401-C Bedienungsanleitung

Elmdene

Elmdene VRS124000-P Series Bedienungsanleitung

Elmdene

Elmdene STX2410-MOD Bedienungsanleitung

Elmdene

Elmdene LPS-ENC-T Bedienungsanleitung

Elmdene

Elmdene LPS-12-G2 Bedienungsanleitung

Elmdene

Elmdene STX2410-H Bedienungsanleitung

Elmdene

Elmdene G1380xBM Series Bedienungsanleitung

Elmdene

Elmdene 20182423N Bedienungsanleitung

Elmdene

Elmdene TR2 Bedienungsanleitung

Elmdene

Elmdene GEN2-08 Series Bedienungsanleitung

Elmdene

Elmdene G240 BM Series Bedienungsanleitung

Elmdene

Elmdene 2405ST Series Bedienungsanleitung

Elmdene

Elmdene STX2405-MOD Bedienungsanleitung

Elmdene

Elmdene 2401ST Bedienungsanleitung

Elmdene

Elmdene STX2402 Series Bedienungsanleitung

Elmdene

Elmdene GEN3-08-y Bedienungsanleitung

Elmdene

Elmdene 2405ST Series Bedienungsanleitung

Elmdene

Elmdene G1380 BMU-y Series Bedienungsanleitung

Elmdene

Elmdene STX2405-E Bedienungsanleitung

Elmdene

Elmdene G2410BMU Bedienungsanleitung

Elmdene

Elmdene G240 N Series Bedienungsanleitung

Elmdene

Elmdene G1380xN-y-s Series Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung