Elmdene GEN2-08 Series Bedienungsanleitung

13.8Vdc Switch Mode Power Supply

GEN2-08-y

for 8Ah attery and up to 1.0A* Continuous Load Current

GEN2-18-y

for 18Ah attery and up to 1.5A* Continuous Load Current

EATURES

High efficiency cost effective power supply suitable for use in systems designed to comply with

PD6662:2010 and EN50131-6:2008 Grade 2 and Environmental Class II requiring 8Ah or 18Ah standby

battery capacity. Two independent output signals are provided for loss of mains fault (EPS**), and

general fault (including APS** fault). Self-diagnostics can detect blown output and battery fuses and

low battery voltage (APS fault). The PSU incorporates a battery management system comprising low

battery voltage detection and deep discharge protection to ensure that the battery is not permanently

damaged through excessive discharge. A brownout filter ensures that short mains voltage dips do not

create a false loss of mains alarm. Two LEDs assist with quick and easy installation by showing

presence of mains, correct battery charging and a fault condition. Comprehensive protection is built-in

as standard including mains transient filtering, electronic output overload protection and fuses on the

load and battery outputs.

•PD6662:2010 and EN50131-6:2008

Type A, Security Grade 2

Environmental Class II Compliant

•Low quiescent battery monitoring current during standby operation

•Fault signals for loss of mains, power supply fault, and battery low voltage warning

•Battery Deep Discharge Protection

•Protection against reverse battery connection

•LED for comprehensive diagnostics

•Thermal protection of power circuitry

•Mains transient suppression and brown-out filter

•Fully enclosed lid tamper circuit

“y” Denotes enclosure size – see overleaf

* See table overleaf to determine continuous standby battery current available for given standby times

** EN50131 Definitions: EPS = External Power Source APS = Alternative Power Source

Elmdene International Ltd

Tel: +44(0)23 9269 6638

3 Keel Close, Interchange Park, Fax: +44(0)23 9266 0483

Portsmouth, Hampshire, PO3 5QD, UK 

Web: www.elmdene.co.uk

PECIFICATION

Mains Input

Rated Voltage / (Operational Voltage) 100-240Vac / (90 – 265Vac)

Frequency 50/60Hz

Input current GEN2-08 & GEN2-18 < 1.0A at full load

Fuse T2A 20mm HRC

Output

GEN

Voltage at full load

Mains power

Battery standby

12.8 –14.2Vdc (13.8Vdc nominal)

9.8 – 13.0Vdc

Ripple

400

–

pk max @ Rated Voltage

Load

Battery

F1.0A

F1.6A

Continuous Output Current

Mains

Battery for 12 hours

1.0 A

0.6A with 8Ah Battery

1.5A

1.5A with 18Ah Battery

*See below for quiescent current of PSU under battery when calculating total system standby current resources.

Mechanical

Product

Reference

GEN

GEN2-18-

GEN

GEN2-18-C

Enclosure Dimensions

w x h x d (mm)

230 x 200 x 80

355 x 330 x 80

330x 275 x 80

Weight (kg)

excluding battery

2.0

4.0

3.3

Material

1.2mm steel white powder

coated

Environmental

Temperature -10 to +40°C (operating) 75% RH non-condensing

-20 to +80°C (storage)

Standby attery Management

Warning: risk of explosion if incorrect battery type fitted

Maximum Battery Size GEN2-08: 8Ah 12V Valve Regulated Lead Acid

(Not supplied with unit) GEN2-18: 18Ah 12V Valve Regulated Lead Acid

Intelligent Battery Recharge Time: < 72 hours to 80% - A heavily discharged battery having a

terminal voltage > 9.0V will attempt to be charged.

Testing: Battery Not Present: <9.0V battery voltage

Low battery voltage: <11.5V (no mains present)

Protection: Reverse battery connection protection

Deep discharge protection - Battery disconnect at 10.6V battery

terminal voltage

Quiescent Current: 64 mA when running on battery - less than 1 mA after deep

discharge protection.

Battery Cold Start (BCS) Momentarily link BCS pins together to connect battery to load if

PSU commissioned without any mains

IGNALLING

UTPUTS

Rating: 0.10A @ 60Vdc 16Ω solid state relay contacts, volt free.

EPS Fault: Open if Loss of mains for >8s

GEN Fault: Open if Battery terminal voltage < 11.5v (when operating in standby with no

mains present), battery not present or Output and/or battery fuse blown

Tamper: 0.5A @ 30Vdc volt free contact. Open when lid is open.

ONNECTIONS

O/P +, - Connection to equipment to be powered (Observe polarity)

EPS Fault: Relay output for mains fail. Open if loss of mains.

GEN Fault: Relay output for General Fault. Open in fault condition

BATT +, - Connection to standby battery. Use cables provided (Observe polarity)

NSTALLATION AND

OMMISSIONING

This unit is only suitable for installation as permanently connected equipment. This PSU is NOT SUITABLE for

external installation. EQUIPMENT MUST BE EARTHED. Before installation, ensure that external disconnect

device is OFF.The PSU should be installed according to all relevant safety regulations applicable to the

application.

Fig 1 Mounting of Power Supply

L E N

Min 10cm clearance

Fasten cables

using cable tie

3A min

FUS

SPUR

Load output cable:

Current rating to

match maximum load

Mains Input cable rated:

3A, 300Vac minimum

Mounting

1) Mount securely in correct orientation allowing minimum clearance – see Fig. 1.0.

2) Ensure that the rear tamper is not in a position that will affect its operation, for example over a mortar

course, recess or raised area on the wall.

3) Route mains and low voltage output cables via different knockouts and/or cable entry holes.

4) Use bushes and cable glands rated to UL94 HB minimum.

Mains Power Up

5) Attach correctly rated mains cable (minimum 0.5mm

[3A], 300/500Vac). Fasten with cable ties.

6) Apply mains power.

Check for 13.8V on load outputs.

Check green Mains LED is ON.

7) Disconnect mains power.

Load Output

8) Loop correctly rated load cable through supplied ferrite (1 turn) and attach to terminal block, note

polarity. Fasten with cable ties.

Fig 2 Position of ferrite

9) Apply mains power.

Check Green Mains LED is ON.

NOTE: Red Fault LED may flash to indicate no battery has been connected, this is normal.

Verify load is operating correctly.

10) Disconnect mains power.

Signalling

11) Connect EPS and GEN fault outputs to appropriate inputs of control and indicating equipment (CIE).

Standby attery

12) Attach supplied battery cables to terminal block and batteries.

NOTE: ensure correct polarity of battery connections: +ve use Red lead, -ve use lack lead.

13) Position the battery as shown in Figures 2 - 6 below, avoiding the cover earth connection spades and

the cover retaining screws. Fold up ‘Tabs’ to locate battery and secure with the rubber band supplied.

Fig 2 GEN2-08-A

Battery

Fold up ‘Tabs’ to locate

battery and secure with the

rubber band supplied

Fold up ‘Tabs’ to locate

battery and secure with

the rubber band supplied

Fold up ‘Tabs’ to locate

battery and secure with the

rubber band supplied

Fig 3 GEN2-18-B Fig 4 GEN2-08-B

Fig 5 GEN2-18-C Fig 6 GEN2-08-C

14) Apply mains power.

Check that Green Mains LED is ON.

Check there is no fault indicated by the Red Fault LED, refer to diagnostic table on page 6.

15) Disconnect mains power.

Check that the batteries continue to supply voltage and current to the output load.

Check that Green Mains LED is OFF and the control panel displays a Loss of Mains (EPS) fault

NOTE: Batteries must have sufficient charge to supply the output load

16) Reconnect mains power.

Check that Green LED is ON.

17) Remove Output fuse.

Check that Red Fault LED is indicating a fault, refer to diagnostic table on page 6, and that the

control panel shows a General PSU fault.

18) Replace Output fuse.

Check that Red Fault LED is OFF and General PSU fault has cleared at control panel.

Battery

Batter

Battery

Fold up ‘Tabs’ to locate

battery and secure with

the rubber band supplied

Fold up ‘Tabs’ to locate

battery and secure with

the rubber band supplied

Battery

Tamper

19) Connect tamper switch to appropriate inputs of control and indicating equipment (CIE).

Fig 7 Position of tamper assembly on ‘hinged lid’ style enclosures

Fig 8 Position of tamper assembly on ‘clam shell’ style enclosures

20) Close the lid and fasten with screw supplied. Alternatively fit the cover in place, the correct orientation

is with the cover retaining feature engaging over the bottom lip of the base, fasten with screws

supplied.

21) Check that the tamper switch is:

CLOSED when the lid/cover is closed and the retaining screws are fitted.

OPEN when the retaining screws are removed the lid/cover is open.

Use fine adjustment screw if necessary to align set position indicator with set point.

22) Close the lid/cover and fasten.

23) Re-check tamper circuit is closed at control panel.

Tamper Switch Connections

Set position indicator

Fine adjustment screw

Lid Fixing Screw

(Sets tamper switch)

Lid Fixing Screw

(Sets tamper switch)

Tamper switch Connections

Fine adjustment screw

Set position indicator

PERATING

NSTRUCTIONS

In the event of loss of mains, a battery fault or a GEN fault, the corresponding Fault signal contacts will open.

If the output of the PSU fails, the cause of the failure should be investigated e.g. short circuit load,

connection of a deeply discharged battery. The fault should be rectified before restoring power to the PSU. If

any of the fuses require replacing, ensure the correct fuse rating and type is used.

AINTENANCE

Maintenance

This unit is intended for use by Service Personnel only. There are NO USER SERVICEABLE parts inside.

There is no regular maintenance required of the PSU other than periodic testing, and replacement of the

standby battery. Reference should be made to the battery manufacturer's documentation to determine

typical/expected battery life with a view to periodic replacement of the battery.

IAGNOSTICS

Local Diagnostics

Green LED On = Mains Present

Red LED Fault Diagnostics according to table:

Red LED

(fault)

Green LED

(mains) Status

OFF ON Normal: Battery fully charged

One short flash

every second ON Normal: Battery charging but not fully charged

Flashing:

1second On

1 second Off

Fault:

Output fuse or battery fuse blown, or

battery missing

OFF Fault: No mains, output fuse blown

One short flash

every 3 seconds OFF Fault: No mains, battery supplying load.

OFF OFF

Fault:

No mains

No output

Batteries

disconnected or completely discharged

OMPLIANCE

This power supply unit meets the essential requirements of the following EU Directives:

EMC: 2014/30/EU Low Voltage: 2014/35/EU WEEE: 2012/19/EU RoHS2: 2011/65/EU

This product is suitable for use in systems designed to comply with

PD6662:2010 at Grade 2 and Environmental Class II

EN50131-6:2008 Type A Security Grade 2

Environmental Class II

Certification Body: Telefication B.V.

Edisonstraat 12A

Zevenaar, 6902 PK

The Netherlands

+31 (0) 316 - 583 180

http://www.telefication.com

ISPOSAL OF

RODUCT AT

ND OF

IFE

This product falls within the scope of EU Directives 2012/19/EU Waste Electrical and Electronic Equipment

(WEEE) and 2013/56/EU (Battery). At the end of life, the product must be separated from the domestic

waste stream and disposed via an appropriate approved WEEE disposal route in accordance with all national

and local regulations.

Before disposal of the product, any batteries must be removed, and disposed separately via an appropriate

approved battery disposal route in accordance with all national and local regulations. Package used batteries

safely for onward transport to your supplier, collection point or disposal facility.

Caution: Risk of fire or explosion

if bare battery wires are allowed to touch.

See Specification for battery type information. The battery is marked with the crossed out wheelie bin

symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For more information see: www.re y lethis.info

The pa kaging supplied with this produ t may be re y led.Please dispose of pa kaging a ordingly

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elmdene Stromversorgung Handbücher

Elmdene

Elmdene G1380xN-y-s Series Bedienungsanleitung

Elmdene

Elmdene STX2402 Series Bedienungsanleitung

Elmdene

Elmdene 2405STE Bedienungsanleitung

Elmdene

Elmdene POE1230-C Bedienungsanleitung

Elmdene

Elmdene G1380 BMU Series Bedienungsanleitung

Elmdene

Elmdene STX2405-E Bedienungsanleitung

Elmdene

Elmdene LPS-ENC-T Bedienungsanleitung

Elmdene

Elmdene 2405ST Series Bedienungsanleitung

Elmdene

Elmdene UNIVERSAL-12V-5A-M Bedienungsanleitung

Elmdene

Elmdene G2410BMU Bedienungsanleitung

Elmdene

Elmdene 2405ST Series Bedienungsanleitung

Elmdene

Elmdene G240 BM Series Bedienungsanleitung

Elmdene

Elmdene STX2401-MOD Bedienungsanleitung

Elmdene

Elmdene STX2410-H Bedienungsanleitung

Elmdene

Elmdene G240 N Series Bedienungsanleitung

Elmdene

Elmdene 2401ST Bedienungsanleitung

Elmdene

Elmdene STX2402-MOD Bedienungsanleitung

Elmdene

Elmdene LPS-12-G2 Bedienungsanleitung

Elmdene

Elmdene STX2401-C Bedienungsanleitung

Elmdene

Elmdene G13804NU Bedienungsanleitung

Elmdene

Elmdene G2410BM-E Bedienungsanleitung

Elmdene

Elmdene STX2410-MOD Bedienungsanleitung

Elmdene

Elmdene VRS124000-P Series Bedienungsanleitung

Elmdene

Elmdene 2402STE Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung