Elsner elektronik KNX DALI L4 bc 16 A Leitfaden

Installation and Adjustment

KNX DALI L4 bc 16 A

Actuator for DALI Light Control

Item number 70580

1 Contents

Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany

Actuator KNX DALI L4 bc 16 A • from application 1.0

Status: 18.05.2020 • Subject to technical changes. Errors excepted.

1. Description ........................................................................................... 3

1.1. Scope of delivery ...................................................................................................... 3

1.2. Technical data ........................................................................................................... 4

2. Installation and commissioning ........................................................... 4

2.1. Installation notes ...................................................................................................... 4

2.2. Device connection and design ................................................................................ 6

2.2.1. Insulation properties of the clamp groups ................................................. 7

2.2.2. Connection example ..................................................................................... 8

2.3. Notes on mounting and commissioning ................................................................ 8

2.4. Buttons and LEDs for the output channels ............................................................ 9

3. Addressing of the device at the bus .................................................... 9

4. Disposal ............................................................................................... 9

5. Transmission protocol ....................................................................... 10

5.1. List of all communication objects ......................................................................... 10

6. Setting the parameters ...................................................................... 19

6.1. Behaviour on power failure/ restoration of power .............................................. 19

6.2. General settings ..................................................................................................... 19

6.3. DALI Bus A / B / C / D .............................................................................................. 20

6.3.1. General ........................................................................................................ 20

6.3.2. Brightness control ....................................................................................... 21

6.3.3. Colour control ............................................................................................. 23

6.3.4. Scenes ......................................................................................................... 24

2 Clarification of signs

This manual is amended periodically and will be brought into line with new software

releases. The change status (software version and date) can be found in the contents footer.

If you have a device with a later software version, please check

www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to-

date version of the manual is available.

Clarification of signs used in this manual

Installation, inspection, commissioning and troubleshooting of the device

must only be carried out by a competent electrician.

Safety advice.

Safety advice for working on electrical connections, components,

etc.

DANGER! ... indicates an immediately hazardous situation which will lead to

death or severe injuries if it is not avoided.

WARNING! ... indicates a potentially hazardous situation which may lead to

death or severe injuries if it is not avoided.

CAUTION! ... indicates a potentially hazardous situation which may lead to

trivial or minor injuries if it is not avoided.

ATTENTION! ... indicates a situation which may lead to damage to property if it is

not avoided.

ETS In the ETS tables, the parameter default settings are marked by

underlining.

3 Description

Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted

1. Description

The Actuator KNX DALI L4 bc 16 A is an interface between KNX bus system and

DALI lighting system (Digital Addressable Lighting Interface). The interface has four

channels for DALI lighting control, each of which can control up to 64 DALI devices

(electronic ballasts). Control is via broadcast message, i.e. all participants on a channel

are switched/dimmed simultaneously. Each channel can be set separately.

Each channel has a switched relay contact through which the DALI devices can be

switched completely de-energised (no standby). The KNX DALI L4 bc 16 A supplies

the DALI bus voltage, no external DALI bus voltage supply is required.

With the KNX DALI L4 bc 16 A, the colour and colour temperature (Tunable White)

can be set for DALI EVGs with device type 8. Both colour settings can be controlled by

scenes, relative or absolute dimming.

In addition to normal operation, the KNX DALI L4 bc 16 A has a night mode and a

staircase lighting function with prewarning function (and both in combination).

Buttons on the device allow direct manual switching and dimming of the connected

DALI EVGs even without bus voltage. The LEDs indicate whether the relay is open or

closed (upper LEDs) and whether the lamp is on or off after a DALI command (lower

LEDs). The DALI EVGs can be controlled by the ETS with the buttons for commission-

ing on site without KNX power supply and without prior configuration.

Functions:

•Interface between KNX bus system and DALI lighting system

•4 channels, each of which can control up to 64 DALI participants. Each channel

can be set separately and has one switching output (230 V AC) and two DALI

bus terminals

•Broadcastoperation: all DALI participants of a channel are controlled with a

common signal, whereby individual addressing is not possible

• Switch panel with 8 buttons and status LEDs

• Minimum switch-on delay from relay to relay: When several channels are

switched on simultaneously, this ensures that the switch-on current of the

EVGs is distributed over time (and thus limited)

• Colour temperature control (Tunable White), RGB/RGBW colour control, HSV

colour control

• Scene recalls

• Status feedback

• Timer function

Configuration is made using the KNX software ETS. The product file can be down-

loaded from the Elsner Elektronik website on www.elsner-elektronik.de in the “Ser-

vice” menu.

1.1. Scope of delivery

•Actuator

4 Installation and commissioning

Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted

1.2. Technical data

The product is compliant with the provisions of EU Directives.

2. Installation and commissioning

2.1. Installation notes

Installation, testing, operational start-up and troubleshooting should

only be performed by an electrician.

DANGER!

Risk to life from live voltage (mains voltage)!

There are unprotected live components within the device.

• VDE regulations and national regulations are to be followed.

• Ensure that all lines to be assembled are free of voltage and take

precautions against accidental switching on.

Casing Plastic

Colour White

Assembly Series installation on mounting rail

IP rating IP 20

Dimensions approx. 107 x 88 x 60 (W x H x D, mm), 6 modules

Weight approx. 270 g

Ambient temperature Operation -20…+45°C, storage -55…+90°C

Ambient humidity max. 95% RH, avoid condensation

Operating voltage 230V AC, 50 Hz

Power consumption Standby: below 1.5 W

all 4 relays closed and all 4 DALI buses consume 128 mA

each: max. 15 W

Power on bus: 10 mA

Outputs 4x switching output 230 V AC, 16 A, 165 A/20 ms, 490 A/1.5

ms (electronic ballast)

4x DALI for max. 64 participants (18 V typical, max. 128 mA

each)

Maximum load Each terminal contact may be loaded with a maximum of

16 A.

Data output KNX +/- Bus plug-in terminal

BCU type own microcontroller

PEI type 0

Group addresses max. 254

Assignments max. 254

Communication objects 165

5 Installation and commissioning

Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted

• Do not use the device if it is damaged.

• Take the device or system out of service and secure it against

unintentional use, if it can be assumed, that risk-free operation is no

longer guaranteed.

The device is only to be used for the intended purpose described in this manual. Any

improper modification or failure to follow the operating instructions voids any and all

warranty and guarantee claims.

After unpacking the device, check it immediately for possible mechanical damage. If it

has been damaged in transport, inform the supplier immediately.

The device may only be used as a fixed-site installation; that means only when assem-

bled and after conclusion of all installation and operational start-up tasks and only in

the surroundings designated for it.

Elsner Elektronik is not liable for any changes in norms and standards which may occur

after publication of these operating instructions.

6 Installation and commissioning

Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted

2.2. Device connection and design

Fig. 1

1 Label field

2 Programmable LED (BUS) and programmable buttons (PRG)

3 Bus terminal socket (KNX +/-)

4 Network LED (power)

Channel A (corresponding to B, C, D):

5 LED "relay" Channel A:

LED on: Relay closed

LED off: Relay open

6 "Switch on/brighter" button Channel A

7 "Switch off/darker" button Channel A

8 LED "lamp" Channel A:

LED on: Switched on (DALI)

LED off: Switched off (DALI)

9 Connections switching output Channel A

10 Connections DALI Bus A

1 2

9 10

7 Installation and commissioning

Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted

The Actuator KNX DALI L4 bc 16 A is installed on a DIN rail (in-line installation on

top-hat rail). The connection to the KNX data bus is made via a KNX connection termi-

nal and is insulated according to the requirements of SELV circuits. In addition, the de-

vice is connected to the mains voltage, which is also used to switch the DALI devices.

The KNX DALI L4 bc 16 A supplies the DALI bus voltage via the DALI bus terminals

(DA) at the same potential.

When installing and laying the cables for the KNX connection,

the regulations and standards governing SELV current circuits

must be observed!

The physical address is assigned by the ETS. There is a button with a control LED for

this on the actuator.

2.2.1. Insulation properties of the clamp groups

The Actuator KNX DALI L4 bc 16 A is assigned to Overvoltage category III and Pol-

lution degree 2 or 3 according to EN60664-1. According to this classification,

between 250 V power cables and FELV 4 kV surge voltage resistance and

between 250 V power cables and FELV 6 kV surge voltage resistance

must be provided. This provision must be observed during the installation.

With single insulation, there may be

a voltage of 400 V AC at pollution degree 2 and

a voltage of 250 V AC at pollution degree 3 between two channels.

Neighbouring clamp groups must not be assigned mixed voltag-

es, as they are only single insulated against each other.

Fig. 2 Insulation properties of the clamp groups

Insulation 6 kV (increased insulation)

Insulation 4 kV (single insulation)

Note: all 4 DALI buses have the same potential

8 Installation and commissioning

Actuator KNX DALI L4 bc 16 A • Version: 18.05.2020 • Technical changes and errors excepted

2.2.2. Connection example

2.3. Notes on mounting and commissioning

Device must not be exposed to water (rain). This could result in the electronic being

damaged. A relative air humidity of 95% must not be exceeded. Avoid bedewing.

After the operating voltage has been applied, the device will enter an initialisation

phase lasting a few seconds. During this phase no information can be received or sent

via the bus.

Nr. 70580

KNX DALI L4 bc 16A

KNX-Lichtregler

Netz

L‘BL‘AL‘CL‘D

L‘

L‘‘

EVG

Mains

(230 V AC)

Fig. 3:

Connection example for electronic enhanced voltage generators for output D (out-

puts A, B and C correspondingly).

The connection of the switching output L'' is only required if the DALI devices on the

corresponding channel are to be completely de-energised.

Each terminal contact may be loaded with a maximum of 16 A.

internally bridged

Cables

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere elsner elektronik Controller Handbücher

elsner elektronik

elsner elektronik KNX S4-B12 DES Bedienungsanleitung

elsner elektronik

elsner elektronik KNX RF S1R-B2 compact Leitfaden

elsner elektronik

elsner elektronik KNX R1-B4 compact 16 A Leitfaden

elsner elektronik

elsner elektronik Cala Touch KNX Bedienungsanleitung

elsner elektronik

elsner elektronik KNX K8 Leitfaden

elsner elektronik

elsner elektronik KNX S1R-B4-UP DES Bedienungsanleitung

elsner elektronik

elsner elektronik RF-MSG2-DST Bedienungsanleitung

elsner elektronik

elsner elektronik Nunio KNX M-T Leitfaden

elsner elektronik

elsner elektronik KNX S-B4T-UP 230 V Gebrauchsanweisung

elsner elektronik

elsner elektronik KNX S1R-BA4-UP Leitfaden

elsner elektronik

elsner elektronik KNX S-B2-UP 230 V Gebrauchsanweisung

elsner elektronik

elsner elektronik KNX R4 16 A Leitfaden

elsner elektronik

elsner elektronik KNX S2 Bedienungsanleitung

elsner elektronik

elsner elektronik KNX RF-MSG-DST Leitfaden

elsner elektronik

elsner elektronik KNX RF-MSG-ST Bedienungsanleitung

elsner elektronik

elsner elektronik 70711 Bedienungsanleitung

elsner elektronik

elsner elektronik KNX eTR MultiTouch Bedienungsanleitung

elsner elektronik

elsner elektronik KNX Touch One Style Bedienungsanleitung

elsner elektronik

elsner elektronik KNX K4 Bedienungsanleitung

elsner elektronik

elsner elektronik KNX S4-B10 230 V Bedienungsanleitung

elsner elektronik

elsner elektronik KNX eTR 205 Light Leitfaden

elsner elektronik

elsner elektronik KNX RF-MSG2-DST Bedienungsanleitung

elsner elektronik

elsner elektronik KNX S1R-B4-UP DES Leitfaden

elsner elektronik

elsner elektronik KNX S1R-B4 compact Leitfaden

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

elsner elektronik KNX DALI L4 bc 16 A Leitfaden

Beliebte Controller Handbücher anderer Marken