Elumen8 ELUM053 Bedienungsanleitung

ELUM053

User Manual

Please read the user manual before use

!!!

1!A!

!!!

2!A!

Table of Contents

1，Safety Information…………………………………………………. 3

2，Rear Panel…………………………………………………………. 5

3，Preparation for Use ………………………………………………...5

4，Main Functions ..………………………………………………….. 6

5，Remote Control…………………………………………………….10

6，Technical Specification…………………………………………….12

!!!

3!A!

1. Safety Information

Warning: This product is for professional use only! It is not for

household use.

The Plasma 1K White presents risks of lethal or severe injury due to fire

and heat, electric shock, ultraviolet radiation, and falls. Flashing light is

also known to trigger epileptic seizures in persons who are

photosensitive. Read this manual before powering or installing the fixture,

follow the safety precautions listed below and observe all warnings in this

manual and printed on the fixture.

Noted: high voltage in the LED board!

High power strobes, so please avoid extended periods of

continuous flashing

To guard against electric shock

!Do not remove the rear cover: there are no user-serviceable parts inside.

!Always ground (earth) the fixture.

!Use only a source of AC power that complies with local building and electrical

codes and has both overload and ground-fault protection.

!Do not expose the fixture to rain or moisture.

To guard against UV radiation, burns, and fire

!Never operate the fixture with the front glass open, missing or damaged.

!Do not stare directly into the light. Never look at an exposed LED while it is lit.

!Never attempt to bypass the fuse. Always replace defective fuses with ones of the

specified type and rating.

!Verify that the power feed cable is rated for the current draw of all connected

fixtures.

!Keep all combustible materials (for example fabric, wood, paper) at least 0.5 meters

away from the fixture.

!Keep flammable materials well away from the fixture.

!Minimum distance to illuminated surface is 10 meters.

!Provide a minimum clearance of 30cm around fixture air vents.

!Never place filters or other materials over the front glass cover.

!The exterior of the fixture can reach high temperatures. Allow the fixture to cool for

!!!

4!A!

at least 15 minutes before handling.

!Do not modify the fixture or install anything other than genuine parts.

!Do not operate if the ambient air temperature (Ta) exceeds 40° C (104° F).

To guard against falls

!When suspending the fixture above ground level, verify that the structure can hold

at least 10 times the weight of all installed devices.

!Verify that all external covers and rigging hardware are securely fastened and use

an approved means of secondary attachment such as a safety cable.

!Block access below the work area whenever installing or removing the fixture.

To guard against epileptic seizure

!Do not operate the fixture near stairways.

!Provide advance notice that strobe lighting is in use.

!Avoid extended periods of continuous flashing, particularly at frequencies of 10 to

20 flashes per second.

For AC 220-240V power supply, the maximum fixtures that can be connected on one

power cable is 6(including the first fixture) ;

For AC 100~120V power supply, the maximum fixtures that can be connected on one

power cable is 3 (including the first fixture).

!!!

5!A!

2. Rear Panel

1, POWER IN/OUT:

PowerCon connection from main power supply, and connection for main power

supply to the next unit.

2, Circuit Breaker: T6.3A

3. LED display

4, LED indicator:

Signal

Flash

Signal input present

Master

Slave

Sound

Flash

Sound activation

5, Menu /UP/DOWN/ Enter button

6, DMX input/output

7, Microphone: Receive music signal for sound active mode

8, CA-8 Connector: Connect with easy controller CA-8

3. Preparation for Use

INSTALLATION

The Plasma 1K White may be installed in any orientation. The mounting bracket

provides five 12 mm holes for direct fastening or attachment of rigging clamps.

!!!

6!A!

4. Main Function

Press MENU button to enter the function, then use the UP/DOWN or MENU

buttons to select the function you want. Press the ENTER button to confirm

your selection. Wait for 30 seconds to return to the main menu or hold the

MENU button for 1 second.

The main menu as follows:

DMX 512 address setting

Select ADDR option and the display will blink, press the ENTER button to

confirm your selection. You can check the current DMX address on the

display. The DMX address can be changed by pressing the UP/DOWN

buttons and then press the ENTER button to confirm your selection. Wait for

30 seconds to return to the main menu or hold the MENU button for 1

second.

!!!

7!A!

Channel mode setting

Select the CHND option and press the ENTER button to confirm your

selection. Change the channel mode from (1/2/3/4/) channels by pressing

the UP/DOWN buttons. Press the ENTER button to confirm your selection.

Wait for 30 seconds to return to the main menu or hold the MENU button for

1 second.

Master/Slave Mode

Select the option and press the ENTER button to confirm your

selection. Select the (Master) 、-（Slave）（ Note: Each

4 units perform as one show group, slave will perform as master if

select ）by pressing the UP/DOWN buttons. Press the ENTER button to

confirm your selection. Wait for 30 seconds to return to the main menu or

hold the MENU button for 1 second.

Show Dimmer

Select the option and press the ENTER button to confirm your

selection. Select the dimmer value from …by pressing the

UP/DOWN buttons. Press the ENTER button to confirm your selection. Wait

for 30 seconds to return to the main menu or hold the MENU button for 1

second.

Show Mode

Select the option and press the ENTER button to confirm your

selection. Select the show from - by pressing the

UP/DOWN buttons. The shows are valid when the units are set to master or

under master/slave mode.Press the ENTER button to confirm your

selection. Wait for 30 seconds to return to the main menu or hold the MENU

!!!

8!A!

button for 1 second.

Blackout Mode

Select the option and press the ENTER button to confirm your

selection. Select (when no DMX signal is present the fixture will be

in blackout) or (when no DMX signal is present the fixture will run in

show mode). Press the ENTER button to confirm your selection. Wait for 30

seconds to return to the main menu or hold the MENU button for 1 second.

Sound Mode

Select the option and press the ENTER button to confirm your

selection. Select the / by pressing the UP/DOWN buttons.

Press the ENTER button to confirm your selection. Wait for 30 seconds to

return to the main menu or hold the MENU button for 1 second. Sound mode

will only be available once the fixture is set as a master unit.

Sound sense

Select the option and press the ENTER button to confirm your

selection. Select the sensitivity from 000-100 by pressing the UP/DOWN button.

Press the ENTER button to confirm your selection. Wait for 30 seconds to

return to the main menu or hold the MENU button for 1 second.

LED display setting

Select the LED option and press the ENTER button to confirm your selection.

You can view the current ON/OFF status of the LED display now. You can

change its status by pressing the UP/DOWN buttons and then press the

ENTER button to confirm your selection. If you choose OFF, the LED display

will blackout after I minute. Wait for 30 seconds to return to the main menu or

!!!

9!A!

hold the MENU button for 1 second.

LED display direction setting

Select the DISP option and press the ENTER button to confirm your

selection. Select the DISP / DSIP by pressing the UP/DOWN button. Press

the ENTER button to confirm your selection. Wait for 30 seconds to return to

the main menu or hold the MENU button for 1 second.

Test setting

Select the TEST option and press the ENTER button to confirm your

selection. The flash indicator will light up and the unit will run an automatic

test . Once the self-test has finished it will return to the test menu. Wait for

30 seconds to return to the main menu or hold the MENU button for 1

second.

Temperature

Select the TEMP option and press the ENTER buttons, the display will show

the temperature of unit. Wait for 30 seconds to return to the main menu or

hold the MENU button for 1 second.

Defaults

Select the DEF option and press the ENTER buttons. Select the

defaults or not by pressing the UP/DOWN button. Press the ENTER

button to confirm your selection. Wait for 30 seconds to return to the main

menu or hold the MENU button for 1 second.

Fixture Hours

Select the FHRS and press the ENTER button to confirm. The display will

Inhaltsverzeichnis

Andere Elumen8 Scheinwerfer Handbücher

Elumen8

Elumen8 Tri Pixel Panel 25 ELUM085 Bedienungsanleitung

Elumen8

Elumen8 Endura WW100 Bedienungsanleitung

Elumen8

Elumen8 Stage Par 220 Bedienungsanleitung

Elumen8

Elumen8 ZF LED Zoom Fresnel ELUM090 Bedienungsanleitung

Elumen8

Elumen8 ELUM062 Bedienungsanleitung

Elumen8

Elumen8 Beam 1RE Bedienungsanleitung

Elumen8

Elumen8 ELUM042 Bedienungsanleitung

Elumen8

Elumen8 Alu Quad Par 64 Bedienungsanleitung

Elumen8

Elumen8 ELUM121 Bedienungsanleitung

Elumen8

Elumen8 ELUM054A Plasma 3K RGB Bedienungsanleitung

Elumen8

Elumen8 Alu Quad Par 64 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung