Elvid OCM-7P-HDR Bedienungsanleitung
QUICKSTART
GUIDE
FIELDVISION
OCM-7P-HDR
7" Professional Field Monitor
2
• Exposure to high sound levels
can cause permanent hearing
loss. Avoid listening at high
volumes for extended periods
of time.
• Keep this product away from
water and any ammable
gases or liquids.
• Do not expose this product
to humidity or extreme heat
or cold.
• Make sure this product is
powered off when plugging it
into a power source.
• Use only the correct,
recommended voltage.
• Do not attempt to disassemble
or repair this product.
• Do not place or store the
monitor facedown, since this
can damage the screen.
• Handle this product with care.
Avoid any impacts to this
product.
• Do not block the vents in this
product.
• Disconnect this product from
its power source before storage
and during electrical storms.
• Do not use chemical solutions
to clean this product. Clean it
with only a soft, dry cloth.
• Keep this product away from
children.
• Make sure that this product
is intact and that there are no
missing parts.
• To avoid damage to this
product, be careful not to
overtighten or improperly
thread any of the threaded
ttings.
• All images are for illustrative
purposes only.
PRECAUTIONS
3
BOX
CONTENTS
• Monitor
• Sun hood
• Sun-hood frame
• Mini HDMI to HDMI cable
(C to A)
• Shoe-mount ball head
• Battery adapter and
mounting screws
• NP-F battery plate
• LP-E6 battery plate
• V-mount battery adapter
and mounting screws
• 1/4-20 screw and hex key
• 12 V DC power supply
4
OVERVIEW
FIELDVISION OCM-7P-HDR
Heat vents
1/4-20 threaded
mounting sockets
5
IN
MENU EXIT F1 F2 INPUT
SDI OUT USB OUT HDMI IN DC 12V
Scroll wheel
Exit button /
mute button
F1 and F2 buttons
Input selector
Speaker
HDMI input
connector
HDMI output
connector
Headphone
jack
USB port
SDI output
connector
SDI input
connector
Power input
Battery plate
mounting holes
6
OFF
ON
Power switch
1/4-20 threaded
mounting socket
7
GETTING
STARTED
ATTACHING A BATTERY PLATE
1. Align the battery adapter
with the four mounting
holes on the back of the
monitor, and screw it in
with the included screws.
2. Attach the power cord to
the power input.
3. Place the NP-F or LP-E6
battery plate into the
adapter, making sure
to align the plate’s and
adapter’s contacts. Slide
the battery plate into the
adapter until it locks in place.
INSTALLING THE BATTERY
1. Place an NP-F or LP-E6 type battery into the battery plate,
making sure the plate’s contacts align with the battery
terminals.
8
2. Slide the battery toward the contacts until it’s rmly in
place.
ATTACHING THE SUN HOOD
Attach the sun hood to the monitor by following these steps:
1. Attach the sun hood to
the sun-hood frame by
pressing the touch-
connect strips together.
2. Attach the frame and the
sun hood to the monitor
by hooking the short
clips to the bottom of the
monitor.
3. Gently push up on the
long clips, and slide
them over the top of the
monitor until they click
into place.
9
MOUNTING THE MONITOR ONTO A CAMERA
1. Determine the monitor orientation you prefer, and screw
the ballhead into the bottom or side 1/4-20 threaded socket
until it’s tight.
2. Loosen the mounting foot by turning the locking wheel
clockwise. Make sure the side tilt adjustment knob is tight,
and the ballhead is locked in place.
3. Fully insert the foot into the camera’s shoe, and tighten the
locking wheel by turning it counterclockwise until secure.
4. Adjust the monitor angle by holding onto it while loosening
the adjustment knob. Change the monitor’s position, and
tighten the tilt adjustment knob until the monitor does not
slip.
MOUNTING THE MONITOR TO A CAMERA RIG
To mount the ballhead directly to an accessory with 1/4-20
mounting sockets, like a shoulder rig or slider, follow these
steps:
1. Tighten the ballhead’s tilt
adjustment knob, and then
remove the mounting foot
by unscrewing it.
10
2. Screw the 1/4-20 screw
into the socket, and
tighten it with the hex key.
3. Screw the ballhead into
a 1/4-20 socket until it’s
snug.
4. Screw the monitor onto the ballhead, and secure it by
tightening the locking wheel.
CONNECTING TO A CAMERA
HDMI: Connect the monitor’s HDMI input to a camera with an
HDMI output.
SDI: Connect the monitor’s SDI input to a camcorder or camera
with an SDI output.
OUTPUTTING THE SIGNAL
Use the HDMI and SDI output to send the signal to a monitor
or recorder.
POWERING ON
1. Connect a battery or DC power source.
2. Switch the power switch to the on position.
Inhaltsverzeichnis
Andere Elvid Monitor Handbücher
Elvid
Elvid OCM-7B-4KV2 Bedienungsanleitung
Elvid
Elvid RigVision CM-7L Bedienungsanleitung
Elvid
Elvid RVM-7B-ALT Bedienungsanleitung
Elvid
Elvid WCM-758G SkyVision Bedienungsanleitung
Elvid
Elvid Studiovision STV-150-4KH Bedienungsanleitung
Elvid
Elvid FIELDVISION OCM-89-4KH Bedienungsanleitung
Elvid
Elvid OCM-7B-D FieldVision Bedienungsanleitung
Elvid
Elvid STUDIOVISION SRM-7X2-4KH Bedienungsanleitung
Elvid
Elvid OCM-7PWV Bedienungsanleitung
Elvid
Elvid SKYVISION WCM-55-HD Bedienungsanleitung
