EM AAA221 Handbuch
Break-out Systems
EM Break-out System
AAA221
Installation and Service Manual -
Original instructions
1003658-EMEI-2.0 –Issue 2014-03-20
© All rights in and to this material are the sole property of Entrematic Group AB. Copying, scanning, alterations or modifications are
expressly forbidden without the prior written consent of Entrematic Group AB. Rights reserved for changes without prior notice.
Backtrack information: folder:Workspace Main, version:a109, Date:2014-03-19 time:16:13:49, state: Frozen
CONTENTS
41 Revision .....................................................................................................................................................................................
52 Important information .........................................................................................................................................................
62.1 Intended use ....................................................................................................................................................................................
62.2 Safety precautions .........................................................................................................................................................................
62.3 Electronic equipment reception interference .....................................................................................................................
72.4 Environmental requirements .....................................................................................................................................................
83 Pre-installation ........................................................................................................................................................................
83.1 General tips/Safety concerns .....................................................................................................................................................
94 Installation ................................................................................................................................................................................
94.1 Checking ...........................................................................................................................................................................................
94.2 Installation on door leaves ..........................................................................................................................................................
94.2.1 Fitting the ball catch shoe .........................................................................................................................................
104.2.2 Attachment of the break-out fitting .......................................................................................................................
114.3 Fitting the floor guide ...................................................................................................................................................................
124.4 Fitting the break-out door adaptor .........................................................................................................................................
134.5 Installation of the ball catch .......................................................................................................................................................
144.6 Final adjustment of the ball catch shoe (see also page 9) ................................................................................................
144.7 Fixing the rubber end stops ........................................................................................................................................................
154.8 Fitting the floor guide track ........................................................................................................................................................
164.9 Installation on side screens ........................................................................................................................................................
164.9.1 Fitting the striking plate .............................................................................................................................................
174.10 Fitting the ball catch .....................................................................................................................................................................
184.11 Installation of the intermediate lock for side screens .......................................................................................................
3Issue 2014-03-201003658-EMEI-2.0
CONTENTS
1 Revision
Following pages have been revised:
Revision - →2.0Page
This manual, No. 1003658-EI-1.0, Issue 2014-01-30, replaces earlier version.
1003658-EMEI-2.0Issue 2014-03-204
1 Revision
2 Important information
Instructions for safe operation
•Failure to observe the information in this manual may result in
personal injury or damage to equipment.
•To reduce the risk of injury of persons - use this operator only with
pedestrian doors.
•Do not use the equipment if repair or adjustment is necessary.
•Disconnect supply when cleaning or other maintenance is to be
carried out.
•The operator can be used by children age 8 and above, and persons
with reduced physical, sensory or mental capabilities, or lack of ex-
perience and knowledge, if they have been given supervision or in-
struction by a person responsible for their safety concerning safe
operator use and the possible hazards involved.
This does not however prevent those persons to use the door where
the operator is installed.
•Cleaning and user maintenance shall not be made by children
without supervision.
•Do not let children climb on or play with the door or the fixed/re-
mote controls.
•In all instances, where work is being done, the area is to be secured
from pedestrian traffic, and the power removed to prevent injury.
•The doorset can be operated automatically by sensors or manually
by activators.
5Issue 2014-03-201003658-EMEI-2.0
2 Important information
2.1 Intended use
The EM Break-out System is an automatic sliding door operator developed to facilitate entrances
to buildings and within buildings through sliding doors.
The EM Break-out System is designed to be surface-mounted to the wall or a beam. It is easy to install
for both new construction and retrofit application, and it can be adapted to a wide range of door
requirements. It is to be installed indoors where it is suitable for almost all types of external and
internal sliding doors.
A EM Break-out System operator can be combined with the full range of Entrematic Group safety
units, such as presence and motion sensors.
The door is designed to offer continuous use, a high degree of safety and maximum lifetime. The
system is self-adjusting to the effects caused by normal variations in the weather conditions and
to minor friction changes caused by e.g. dust and dirt.
In emergency situations the doorset is opened and remains open automatically. It may also be
equipped with break-out function, in which case the door leaf is pushed manually open in the escape
direction.
This manual contains the necessary details and instructions for the installation, maintenance and
service of the Sliding Door Operator EM Break-out System.
Save these instructions for future reference.
2.2 Safety precautions
Be sure to complete a risk assessment and site acceptance test before taking the door into operation.
To avoid bodily injury, material damage and malfunction of the product, the instructions contained
in this manual must be strictly observed during installation, adjustment, repairs and service etc.
Training is needed to carry out these tasks safely. Only Entrematic Group-trained technicians should
be allowed to carry out these operations.
2.3 Electronic equipment reception interference
The equipment complies with the European EMC directive (US market FCC Part 15), provided in-
stalled according to Installation and Service manual.
The equipment may generate and use radio frequency energy and if not installed and used properly,
it may cause interference to radio, television reception or other radio frequency type systems.
If other equipment does not fully comply with immunity requirements interference may occur.
There is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•Re-orient the receiving antenna.
•Relocate the receiver with respect to the equipment.
•Move the receiver away from the equipment.
•Plug the receiver into a different outlet so that equipment and receiver are on different branch
circuits.
•Check that protective earth (PE) is connected.
If necessary, the user should consult the dealer or an experienced electronics technician for addi-
tional suggestions.
1003658-EMEI-2.0Issue 2014-03-206
2 Important information
2.4 Environmental requirements
Entrematic Group products are equipped with electronics and may also be equipped with batteries
containing materials which are hazardous to the environment. Disconnect power before removing
electronics and battery and make sure it is disposed of properly according to local regulations (how
and where) as was done with the packaging material.
7Issue 2014-03-201003658-EMEI-2.0
2 Important information
3 Pre-installation
3.1 General tips/Safety concerns
In all instances, where work is being done, the area is to be secured from ped-
estrian traffic, and the power removed to prevent injury.
•If there are sharp edges after drilling the cable outlets, chamfer the edges to avoid damage to
the cables.
•For enhanced security and vandalism protection, always mount the operator access in the in-
terior of a building whenever possible.
•Make sure the ambient temperature is in the range specified in section Technical specification.
•Make sure that the power is off before installing.
•Make sure that the door leaf and the wall are properly reinforced at the installation points.
•Unpack the operator and make sure that all parts are delivered in accordance with the packing
note and that the operator is in good mechanical condition.
•Ensure proper material is being used for the door leaves and that there are no sharp edges.
Projecting parts shall not create any potential hazards. If glass is used bare glass edges shall not
come in contact with other glass. Toughened or laminated glass are suitable glasses.
•Ensure that entrapment between the driven part and the surrounding fixed parts due to the
opening movement of the driven part is avoided. The following distances are considered sufficient
to avoid entrapments for the parts of the body identified;
- for fingers, a distance greater than 25 mm or less than 8 mm
- for heads, a distance greater than
- for feet, a distance greater than 50 mm
- and for the whole body, a distance greater than 500 mm
•The operator may be installed above or below 2.5 m from the floor level.
•The operator shall not be used with a doorset incorporating a wicket door.
1003658-EMEI-2.0Issue 2014-03-208
3 Pre-installation
4 Installation
4.1 Checking
Check that necessary recesses have been cut in the door leaf, side screen and door adaptor and
that the ball catch shoe and the floor guide fit into the door section.
In addition to this instruction, the following drawings are required for a proper installation:
832 273 - Installation drawing, PSB
832 452 - Door leaf for Break-out System, PSB
548 976 - Space required, UniSlide/PSB
832 275 - Ball catch for side screen, PSB
830 555 - Door locking
4.2 Installation on door leaves
4.2.1 Fitting the ball catch shoe
Mount the ball catch shoe into the top rail of the door with the rear head cap Allen screw (slotted
hole). The front screw is to be fitted after final adjustment of the ball catch shoe (see page 13).
1
AAA228
3
2
Ball catch shoe1
Rear head cap Allen screw (M6 x 14)2
Front head cap Allen screw (M6 x 14)3
9Issue 2014-03-201003658-EMEI-2.0
4 Installation
4.2.2 Attachment of the break-out fitting
a Drill attachment holes for the break-out fitting in the door's outer style, using the drill template
provided. Screw clamps assist this operation.
Note! The fixing must be as precise as possible.
b Push the break-out fitting down into the door section and fasten it with 8 countersunk Allen
screws (M6 x 8).
c Use the plastic spacers and longer screws (M6 x 12) if a 4 mm less gap is required between the
fixed screen and the door.
2
AAA227
4
31
Break-out fitting1
Drill template2
Plastic spacer (2 pcs)3
Countersunk Allen screw (8 pcs)4
1003658-EMEI-2.0Issue 2014-03-2010
4 Installation
Inhaltsverzeichnis
Andere EM Medienkonverter Handbücher
