EMC Celerra NS20 Bedienungsanleitung
EMC®Celerra®NS20 System
(Dual Blade)
Installation Guide
P/N 300-007-635 Rev A01
2
Copyright © 2008 EMC Corporation. All rights reserved. Published November, 2008
EMC believes the information in this publication is accurate as of its publication date. The information is
subject to change without notice.
THE INFORMATION IN THIS PUBLICATION IS PROVIDED “AS IS.” EMC CORPORATION MAKES NO
REPRESENTATIONS OR WARRANTIES OF ANY KIND WITH RESPECT TO THE INFORMATION IN
THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE.
Use, copy or distribution of any EMC software described in this publication requires an applicable software
license.
All other trademarks used herein are the property of their respective owners.
For the most up-to-date regulatory document for your product line, go to the Technical Documentation
andAdvisories section on EMC Powerlink. For the most up-to-date listing of EMC product names, see EMC
Corporation Trademarks on EMC.com.
After reviewing this guide, go to Celerra Tools or Powerlink and download the client product guides to
complete your MPFS installation. Log on to Powerlink, open Support > Technical Documentation and
Advisories > Software ~C~ Documentation > Celerra MPFS over Fibre Channel or Celerra MPFS over
iSCSI.
The label, settings, and system cabling information in this document are for your reference. Paste the
Control Station label in this provided space, see page 7.
3
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Before you begin
!
Welcome
The system you are about to install comes factory pre-loaded with Celerra®Network Server software
(DART) and CLARiiON®storage array software (FLARE®).
Software upgrade
If you bought a software maintenance contract, you are entitled to a software upgrade that is
performed only after the installation, Celerra Startup Assistant (CSA), and registration have
successfully completed.
Site preparation
Complete the site preparation by verifying the following activities before installation:
Network connections•
Power requirements•
Rack space requirements•
Default IP addresses
The system components communicate with each other using a private Internet Protocol (IP) network.
By default, this network uses the IP addresses listed in the following table.
If your existing IP network uses addresses on these subnets, you are required to change the private
network addresses of your Celerra Network Server to different subnets before the installation.
Primary internal network 128.221.252.100
Backup internal network 128.221.253.100
Netmask 255.255.255.0
IP address of storage processorA 128.221.252.200
IP address of storage processor B 128.221.253.201
Gateway IP address of storage processorA 128.221.252.104
Gateway IP address of storage processor B 128.221.253.104
Internal system addresses Factory values
4
Installation overview
A
A
B
!!
!!
!
EXP
EXP
PRI
PRI
EXP
EXP
PRI
PRI
#
!
EXP
EXP
PRI
PRI
EXP
EXP
PRI
PRI
#
Step 5. Configure for production.
This CD contains the intellectual property of
EMC Corporation or is licensed to EMC Corporation
from third parties. Use of this CD and the intellectual
property contained herein is expressly limited to the
terms and conditions of the License Agreement.
EMC® Celerra® NS20 System
Tutorial CD
CSA Installation
P/N nnn-nnn-nnn-A0n
Copyright© 2nnn EMC Corporation
All Rights Reserved
C®
C®C
elerra® NS20
ele
Ce
Cel
el
Ce
C
C®
System
Tutorial CD
CSA Installation
P/Nnnn-nnn-nnn-A
C
Copyright©2nnn EM
C
C
C
C
AllRights R
E
EM
EM
MC
MC
MC
MC®
EM
E
M
M
EMC® Celerra® NS20
Back Next Cancel
EMC® Celerra® NS20 System
Tutori al
CSA Installation
P/N nnn-nnn-nnn-A0n
EMC®
Tutorial
CSA Installation
P/N nnn-nnn-nnn-A0n
Installation
Step 1. Order the product
and prepare the site.
Step 4. Register with the
service provider.
Step 3. Install the Celerra
Startup Assistant.
Implementation
Step 2. Assemble and cable
the product on site.
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
5
Installation steps:
Review and complete the Celerra worksheets (see pages 19 and 20), and verify that the site is1.
properly prepared for the installation of your Celerra NS20. About 20 minutes.
If your Celerra NS20 is to be installed in a customer-supplied rack, use this document to unpack2.
the system from the disposable mini-rack shipping container, and install the system in your available
rack. About 40 minutes.
Note: If your Celerra NS20 system arrives at your site in a pre-installed cabinet and is previously
cabled, verify the cabling before you begin the use of your system.
Cable your system according to the instructions and illustrations contained in this document.
Ensure that all of your cables are seated securely. About 45 minutes.
When you install your Celerra NS20, use the Celerra Startup Assistant (CSA) to configure your3.
system. The CSAis on the Celerra Applications & Tools CD. The CSA will help create CIFS shares,
NFS exports, or iSCSI LUNs and to register your Celerra system. About 15 minutes.
Register your system with the service provider. If you do not register your system now, using the4.
Celerra Startup Assistant, your request for support from EMC®Customer Service will be delayed.
About 5 minutes.
Implementation step:
5. After you have registered your Celerra NS20 system, you must configure the system for
production. There are several documented implementation procedures based on common
usages. You can configure your system manually using Celerra Manager, or follow the common
implementations listed below.
Common implementations:
Create CIFS shares• Create iSCSI LUNs• Create NFS exports• Perform Common Post-CSA tasks•
At the end of each implementation, your system will be usable and ready for production.
Note: Configure your system using these procedures to create basic implementations.
To configure additional implementations, follow the Celerra user documentation on Powerlink®.
Installation steps
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
6
Unpacking the Celerra NS20 system
If your Celerra NS20 system was purchased and shipped in an EMC 40 Unit cabinet, (70 in. tall,
where1 unit =1.75 in.), start on page 11 of this document and confirm that the cables are
installed correctly and securely; otherwise start unpacking your Celerra NS20 system from the
disposable mini-rack shipping container.
CNS-000855
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
7
Disposable mini-rack Document kit inventory list
Disk-array enclosure Doc kit: Installation guide
Control Station Read Me First
Standby power supply Cabling diagrams
Storage processor enclosure Environmental compliance information
Blade enclosure Notices
Accessory box 1 Media kit inventory list
Accessory kit docs and bezels Applications and Tools CD
Power cables Software CD
Standby power supply interconnect cable kit User documentation CD
Crossover cable Getting Started with Celerra
Serial cable
Note: The shaded areas in the table represent separate containers, packages, and boxes.
If additional accessory boxes are necessary, they will be shipped separately.
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
LAN1
LAN2
Disk-array
enclosure
Standby power
supply
Control Station
Blade enclosure
Document kit inventory list
and Media kit inventory list
Storage processor
Disposable
mini-rack
IMPORTANT
User Documentation
Accessory box
CIP-1038MOD
Remove this label and
paste it on page 2
of this guide.
Contents of the disposable mini-rack
8
Remove components from shipping container
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
2. Carefully set aside each
component as it is removed from
the mini-rack shipping container.
Caution: Two people are required to remove the components. Only remove screws
holding the components in place at this time. Do not remove the screws holding
the rails in place; this may cause damage to the components. Only remove one
component at a time.
3. The rails remain in the mini-
rack shipping container at this
time.
Front
Mini-rack
Control Station
Storage processor
enclosure
Standby power
supply
Disk-array
enclosure
Blade enclosure
Remove ONLY
8 screws
per side.
Remove ONLY
8 screws
per side.
CIP-001034MOD
Disk array
Standby power supply
Control Station
Blade enclosure
Storage processor
Using a #21. Phillips-head screwdriver,
remove only 8 screws per side. Keep the
removed screws to install the components
in the rack.
!
9
Remove rails and install into the site rack
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
1. Remove the screws holding the
rails in place. Keep the screws
to install the rails in your rack.
The mini-rack is part of the
shipping container and is not to be
removed.
2. Insert the rail slide and seat
the rail extensions into the rear
channel of your rack.
3. Do not fully tighten the two initial
screws that join the rails to the rack.
Allow some adjustment space for
the installation of the components.
Rail slide
Rail slide
Rail extensions
Remove rear screws.
CNS
-
000854
Front of your rack
Rear of your rack
Rail slide
Rail slide
T
he initial 2 screws on
each side of the rack hold
the rails in place.
Rail extensions
Install rear screws.
Only remove the screws
holding the rails in the mini-rack.
There are 8screws that hold the rails
into the mini-rack.
Protruding PEM screw holes
are located in 4 places on
the front of the rails.
Conserve rack space
when installing rails.
Marked holes on both
rails indicate the place
for initial screws.
Threaded
screw holes
Remove the rails.
10
Components, latches, and bezels
Screws (2 per side)
Front
A and B
bezel bracket
Snap on bezels
Rail catch
Screw (1 per side)
Control Station and standby
power supply shelf
Disk-array enclosure
2 bracket screws each side
Front
Indentation
to center of
the rack
Install the lower
screw rst
screws (2 per side).
Storage processor enclosure
and blade enclosure
Front
2 screws
each side
Install screws through rack
into the rail, 1a through 4a.
Install the bottom component rst.
Ensure that each component
is secure before you install the
component above it.
1a
2a
2b
3a
3b
4a
1
2
3
4
5
CIP-001033MOD
Install the rack and rails with the provided screws.1.
Starting with the bottom component first, install each component.2.
Ensure that each component is installed securely.3.
Install the latches as you install the components.4.
After all the components and latches are in place, snap on the bezels.5.
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Andere Handbücher für Celerra NS20
1
Inhaltsverzeichnis
Andere EMC Lagerung Handbücher
EMC
EMC CloudBoost 100 Montageanleitung
EMC
EMC CX700 Technisches Handbuch
EMC
EMC VNX Series Bedienungsanleitung
EMC
EMC Celerra NS40 Gebrauchsanweisung
EMC
EMC CLARiiON AX150 Series Produkthandbuch
EMC
EMC VNXe3200 Bedienungsanleitung
EMC
EMC Symmetrix DMX-3 Bedienungsanleitung
EMC
EMC Connectrix EC-1200 Technisches Handbuch
EMC
EMC DATA DOMAIN DD4500 Montageanleitung
EMC
EMC VNX Series Bedienungsanleitung
EMC
EMC VNX Series Bedienungsanleitung
EMC
EMC EMC Unity Family Bedienungsanleitung
EMC
EMC CelerraNS-120 Bedienungsanleitung
EMC
EMC FC4700 Technisches Handbuch
EMC
EMC Celerra NS20 Gebrauchsanweisung
EMC
EMC VPLEX Montageanleitung
EMC
EMC Atmos Montageanleitung
EMC
EMC VNX Series Betriebsanleitung
EMC
EMC DATA DOMAIN DD7200 Montageanleitung
EMC
EMC AX4-5 Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung