EMC Celerra NX4 Bedienungsanleitung
EMC®Celerra®NX4 System
Dual Blade
Installation Guide
P/N 300-010-728 Rev A01Version 6.0
EMC believes the information in this publication is accurate as of its publication date. The information is
subject to change without notice.
THE INFORMATION IN THIS PUBLICATION IS PROVIDED “AS IS.” EMC CORPORATION MAKES
NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WITH RESPECT TO THE
INFORMATION IN THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE.
Use, copy, or distribution of any EMC software described in this publication requires an applicable
software license.
For the most up-to-date regulatory document for your product line, go to the Technical Documentation
and Advisories section on EMC Powerlink. For the most up-to-date listing of EMC product names, see
EMC Corporation Trademarks on EMC.com.
All other trademarks used herein are the property of their respective owners.
The label, settings, and system cabling information in this document are for your reference. Paste the
Control Station label in the provided space.
Copyright 2008-2010 EMC Corporation. All rights reserved. Published August, 2010
CNS 001365
3
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
!
Before you begin
Software upgrade
If you bought a software maintenance contract, you are entitled to a software upgrade
that is performed only after the installation, Celerra Startup Assistant (CSA), and
registration have successfully completed.
Site preparation
Complete the site preparation by verifying the following activities before installation:
• Network connections
• Power requirements
• Rack space requirements
Internal system addresses Factory values
Primary internal network 128.221.252.100
Backup internal network 128.221.253.100
Netmask 255.255.255.0
IP address of storage processor A 128.221.252.200
IP address of storage processor B 128.221.253.201
Gateway IP address of storage processor A 128.221.252.104
Gateway IP address of storage processor B 128.221.253.104
Default IP addresses
The system components communicate with each other using a private Internet Protocol
(IP) network. By default, this network uses the IP addresses listed in the “
Internal
system addresses
.”
If your existing IP network uses addresses on these subnets, you are required to
change the private network addresses of your Celerra Network Server to different
subnets before the installation.
Welcome
The system that you are about to install comes factory pre-loaded with EMC®Celerra®
Network Server software (DART) and CLARiiON®storage array software (FLARE®).
4
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Installation overview
Step 5. Configure for production.
Installation
Step 4. Register with the
service provider.
Implementation
Step 3. Install the
Celerra Startup Assistant.
This CD contains the intellectual property of
EMC Corporation or is licensed to EMC Corporation
from third parties. Use of this CD and the intellectual
property contained herein is expressly limited to the
terms and conditions of the License Agreement.
EMC® Celerra® NS20
Back Next Cancel
EMC® Celerra® NS20 System
Tutor ial
CSA Installation
P/N nnn-nnn-nnn-A0n
EMC®
Tutorial
CSA Installation
P/N nnn-nnn-nnn-A0n
Step 2. Assemble and cable
the Celerra NX4 on site.
Step 1. Order the Celerra NX4
and prepare the site.
CNS-001409
5
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Installation overview steps
Installation steps:
1. You should review and complete the worksheets included in this document,
pages 25-30, and verify that the site is properly prepared for the installation of your
Celerra NX4.
About 20 minutes.
2. If your Celerra NX4 is to be installed in a customer-supplied rack, use this document to
unpack the system from the disposable mini-rack shipping container, and install the system
in your available rack.
About 40 minutes.
Note: If your Celerra NX4 system arrives at your site in a pre-installed cabinet and is
previously cabled, verify the cabling before you begin the use of your system.
Cable your system according to the instructions and illustrations contained in this document.
Ensure that all of your cables are seated securely.
About 45 minutes.
3. When you install your Celerra NX4, use the Celerra Startup Assistant (CSA) to configure
your system. The CSAis on the Celerra Applications & Tools CD. The CSA will help you
to create CIFS shares, NFS exports, and iSCSI LUNs, and to register your Celerra NX4
system.
About 15 minutes.
4. Register your system with the service provider. If you do not register your system now, using
the Celerra Startup Assistant, your request for support from your service provider will be
delayed.
About 5 minutes
Implementation step:
5. After you have registered your Celerra NX4 system, you must configure the system for
production. You can use the Provisioning Wizard in the CSA, one of the several
pre-packaged implementation configurations based on common usages, or your own
implementation using Unisphere software to configure your system. At the end of each
one of these configurations, your system will be ready for production.
6
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
If your Celerra NX4 system was purchased and shipped in an EMC 40 unit cabinet of 70 in.,
where 1 unit =1.75 in., start on page 12 of this document and confirm that the cables are
installed correctly and securely.
Otherwise, start unpacking your Celerra NX4 system that is shipped in a disposable mini-rack.
Unpacking your Celerra NX4 system
CNS-001428
7
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Accessory box
Standby power supply interconnect
cable kit
Crossover cables
Fibre Channel cables Ethernet cables for internal network
Power cables Bezels
Serial cables Hardware for non-factory installs
Contents of the disposable mini-rack container
Note: If additional accessory boxes are necessary, they will be shipped separately.
Front
Disk processor
enclosure (DPE)
Standby power supply (SPS)
Control Station (CS)
Blade enclosure
Accessory box
CNS-001427
Shrink-wrapped
Installation Guide,
environmental information,
and notices.
TLASerial Number
ModelNumber
DARTVersion
FlareVersion
UnitTested
Pre-Configured
MACAddress
SPAIP: 192.168.1.200
SPBIP: 192.168.2.201
Disposable mini-rack
shipping container.
Ganged rails
Document inventory list
Installation Guide with cabling diagrams Environmental compliance information
and notices
Disposable mini-rack
Ganged rails Standby power supply
Disk processor enclosure Blade enclosure
Control Station
8
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Remove components from shipping container
Caution: Two people are required to remove the components. Only remove the
screws holding the components in place at this time. Do not remove the screws holding
the mini-rack rails in place; this may cause damage to the components. Only remove
one component at a time.
TLASerial Number
ModelNumber
DARTVersion
FlareVersion
UnitTested
Pre-Configured
MACAddress
SPAIP:192.168.1.200
SPBIP: 192.168.2.201
Control Station (CS)
Standby power supply (SPS)
Disk processor
enclosure (DPE)
Blade enclosure
Do not remove the mini-rack
from shipping container.
CNS-001429
2
3
4
1
Remove this label and
paste it on the back of
the front cover of this
installation guide.
Disk processor
enclosure
Standby power supply
Control Station
Blade enclosure
2
3
4
1
TLASerial Number
ModelNumber
DARTVers ion
FlareVersion
UnitTested
Pre-Configured
MACAddress
SPAIP:192.168.1.200
SPBIP: 192.168.2.201
2. Carefully set aside each component as
it is removed (1-4) from the disposable mini-rack
shipping container.
3. The ganged rails remain in the mini-rack
shipping container at this time.
1. Using a Phillips-head screwdriver, remove only
six
screws per side.
Keep the screws to install the components in your site rack.
!
9
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Ganged rail slide
Rail extensions
Remove rear screws.
CNS-001411MOD
Front of your rack
Rear of your rack
Rail slide
Rail slide
Install 2 screws
to hold the rail
in place.
Rail extensions
Install rear screws.
Only remove the screws
holding the ganged rails
in the mini-rack.
Protruding PEM screw holes
are located in 4 places on
the front of the rails.
Marked holes on both rails
indicate the place
for initial screws.
Threaded
screw holes
Remove the
ganged rails
Install 2 screws
on each side
of the rack to
hold the rail
in place.
Ganged rail slide
1. Remove the larger-headed screws holding the ganged rails in place. Keep the screws to install the
ganged rails in your rack.
2. Remove the ganged rails. Do not remove the metal mini-rack, it is part of the shipping container. The
components are to be installed into your rack with the smaller-headed screws
3. Insert the ganged rail slides and seat the
rail extensions into the rear channels. With
the larger-headed screws you have kept,
start installing the ganged rails into your
rack.
4. Do not fully tighten
the initial two front
screws that join the
rails to the rack.
This allows some
adjustment space
for the installation
of the components.
Remove rails from mini-rack
10
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Components, latches, and bezels
1. Install the bottom component first
( 1 2 3 4 ). Ensure that each component
is secure before you install the next
component above it.
2. Snap on the bezels.
Disk processor enclosure (DPE)
2U latch and 2 screws each side
2 screws each side
Right front side
2
3
4
1
CNS-001430
Rail catch
1 screw each side
Control Station (CS) and
standby power supply (SPS)
1U latch each and
1 screw each, each side
Right front side
Press
Snap on bezels
Press to install the bezel,
then release.
The indentation goes
toward the inside of
the rack.
Install the lower
screw first with 2 screws
on each side.
Right front side
Inside
Blade enclosure
1U latch, 2 screws each side
Inside
1. Install the bottom component first, and continue to individually install each component.
2. Ensure that each component and all screws are secure as the component is installed;
also install the latches as you install each component.
3. After all of the components and latches are in place, snap on the bezels.
Inhaltsverzeichnis
Andere EMC Lagerung Handbücher
EMC
EMC Celerra NS20 Gebrauchsanweisung
EMC
EMC Atmos Montageanleitung
EMC
EMC DATA DOMAIN DD160 Montageanleitung
EMC
EMC CLARiiON CX4-120 Bedienungsanleitung
EMC
EMC EMC2 DATA DOMAIN DD660 Montageanleitung
EMC
EMC AX4-5 Bedienungsanleitung
EMC
EMC Iomega StorCenter ix2-dl Bedienungsanleitung
EMC
EMC VNX Series Betriebsanleitung
EMC
EMC VNX5500 Bedienungsanleitung
EMC
EMC Data Domain DD990 Montageanleitung
EMC
EMC VNX Series Betriebsanleitung
EMC
EMC DL3D 1500 Service-Handbuch
EMC
EMC VNX Series Bedienungsanleitung
EMC
EMC VNX Series Betriebsanleitung
EMC
EMC VNX5300 Block Bedienungsanleitung
EMC
EMC Celerra NS20FC Bedienungsanleitung
EMC
EMC CX500I - Insignia CLARiiON NAS Server Bedienungsanleitung
EMC
EMC EMC Unity Family Bedienungsanleitung
EMC
EMC Disk Library DL4106 Bedienungsanleitung
EMC
EMC Celerra Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung