EMC CelerraNS-120 Bedienungsanleitung

EMC®Celerra®NS-120 System

(Single Blade)

Installation Guide

P/N 300-007-880 Rev A04

EMC believes the information in this publication is accurate as of its publication date.

The information is subject to change without notice.

THE INFORMATION IN THIS PUBLICATION IS PROVIDED “AS IS.” EMC CORPORATION

MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WITH RESPECT TO THE

INFORMATION IN THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Use, copy, or distribution of any EMC software described in this publication requires an applicable

software license.

For the most up-to-date regulatory document for your product line, go to the Technical

Documentation and Advisories section on EMC Powerlink. For the most up-to-date listing of EMC

product names, see EMC Corporation Trademarks on EMC.com.

All other trademarks used herein are the property of their respective owners.

The label, settings, and system cabling information in this document are for your reference. Paste

the Control Station label in the provided space.

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

Before you begin

Welcome

The system you are about to install comes factory pre-loaded with EMC®Celerra®Network Server

software (DART) and CLARiiON®storage array software (FLARE®).

Software upgrade

If you bought a software maintenance contract, you are entitled to software upgrades only after the

installation, Celerra Startup Assistant (CSA), and registration have successfully completed.

Site preparation

Complete the site preparation by verifying the following activities before installation:

• Network connections

• Power requirements

• Rack space requirements

Default IP addresses

The system components communicate with each other using a private Internet Protocol (IP) network.

By default, this network uses the IP addresses listed in the following table.

If your existing IP network uses addresses on these subnets, you are required to change the private

network addresses of your Celerra Network Server to different subnets before the installation.

Primary internal network 128.221.252.100

Backup internal network 128.221.253.100

Netmask 255.255.255.0

IP address of storage processorA 128.221.252.200

IP address of storage processor B 128.221.253.201

Gateway IP address of storage processorA 128.221.252.104

Gateway IP address of storage processor B 128.221.253.104

Internal system addresses Factory values

Installation overview

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

This CD contains the intellectual property of

EMC Corporation or is licensed to EMC Corporation

from third parties. Use of this CD and the intellectual

property contained herein is expressly limited to the

terms and conditions of the License Agreement.

EMC® Celerra® NS20

Back Next Cancel

EMC® Celerra® NS20 System

Tutorial

CSA Installation

P/N nnn-nnn-nnn-A0n

EMC®

Tutorial

CSA Installation

P/N nnn-nnn-nnn-A0n

Step 4. Register with the

service provider.

Implementation

Step 3. Install using the

Celerra Startup Assistant.

Step 2. Assemble and cable

the Celerra NS-120 on site.

Step 1. Order the Celerra NS-120

and prepare the site.

Installation

Step 5. Configure for production. CNS-001465

Installation overview steps

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

Installation steps:

1. Review and complete the Celerra worksheet, pages 31-32,and verify that the site is properly

prepared for the installation of your Celerra NS-120.

About 20 minutes.

2. If your Celerra NS-120 is to be installed in a customer-supplied rack, use this document to unpack

the system from the mini-rack shipping container, remove the reusable rails, and install the system

in your available rack.

About 40 minutes.

Note: If your Celerra NS-120 system arrived at your site in a pre-installed cabinet and is

previously cabled, verify the cabling before you begin the use of your system.

Cable your system according to the instructions and illustrations contained in this document.

Ensure that all of your cables are seated securely.

About 45 minutes.

3. When you install your Celerra NS-120, use the Celerra Startup Assistant (CSA) to pre-conﬁgure

your system. The latest version of the CSA can be downloaded from the Celerra Tools section on

Powerlink®.. The CSAis also on the Celerra Applications & Tools CD.

About 15 minutes.

4. Register your system with the service provider. If you do not register your system now, using the

Celerra Startup Assistant, your request for support from your service provider will be delayed.

You can also register your Celerra NS-120 by downloading the Registration Wizard on Powerlink.

About 5 minutes.

Implementation step:

5. After you have registered your Celerra NS-120 system, you must conﬁgure the system for

production. You can use the Provisioning Wizard in the CSA, one of the several pre-packaged

implementation conﬁgurations based on common usages, or your own implementation using

Celerra Manager to conﬁgure your system. At the end of each one of these conﬁgurations,

your system will be ready for production.

Note: If your Celerra NS-120 system has the Fibre Channel-enabled option use

Navisphere®Manager to provision storage for use by other Hosts.

Unpacking the Celerra NS-120 system

If your Celerra NS-120 system was purchased and shipped in an EMC 40 Unit cabinet, (70 in.

where1 unit =1.75 in.), start on page 15 of this document and conﬁrm that the cables are installed

correctly and securely; otherwise start unpacking your Celerra NS-120 system from the disposable

mini-rack shipping container.

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

CNS-001471

Note: The table represents components that are shipped with Celerra’s disposable mini-rack.

If additional accessory boxes are necessary they will be shipped separately.

Front

Shrink-wrapped Installation Guide,

environmental information and notices

Disposable mini-rack

Accessory box

CNS-001463

Disk-array

enclosure (DAE)

Standby power

supply (SPS)

Control Station

(CS)

Blade enclosure

Storage processor

enclosure (SPE)

Ganged rails

Remove this label and

paste it on the back of

the front cover of this

installation guide.

Ganged rails

Contents of package

Disposable mini-rack Accessory box Document inventory list

Disk-array enclosure Standby power supply interconnect

cable kit

Installation guide with storage

processor options and cabling

diagrams

Ganged rails Fibre Channel cables

Environmental compliance

information and notices

Control Station Power cables

Standby power supply Serial cables

Storage processor enclosure

Crossover cables

Ethernet cables for internal network

Bezels

Hardware for non-factory installs

Blade enclosure

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

Remove components from shipping container

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

2. Carefully set aside each component as

it is removed from the mini-rack shipping

container.

Caution: Two people are required to remove the components. Only remove screws holding

the components in place at this time. Do not remove the screws holding the rails in place; this

may cause damage to the components. Only remove one component at a time.

3. The reusable ganged rails

remain in the mini-rack at this time.

1. Using a Phillips-head screwdriver, remove only 7 screws per side. Keep the removed screws

to install the components in the rack.

Front

Mini-rack

2 Control Station (CS)

4Storage processor

enclosure (SPE)

3 Standby power

supply (SPS)

1Disk-array

enclosure (DAE)

5Blade enclosure

Remove ONLY

7 screws

per side.

Remove ONLY

7 screws

per side.

CNS-001457

Disk-array

enclosure

Standby power supply

Control Station

Blade enclosure

Storage processor enclosure

Remove this label and

paste it on the back of

the front cover of this

installation guide.

TLASerial Number

ModelNumber

DARTVersion

FlareVersion

UnitTested

Pre-Configured

MACAddress

SPAIP:192.168.1.200

SPBIP: 192.168.2.201

Ganged rails

Remove ganged rails from shipping container

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

Remove the screws holding the component rails in place in the disposable mini-rack.

Keep the screws to install the ganged rails in your rack.

Rail slide with extensions

Remove 2 screws

each side.

Disposable mini-rack

Remove the ganged rails

from mini-rack.

Remove the ganged rails

from mini-rack.

CNS-001459MOD

Rail slide with extensions

Front of rack

Threaded

screw holes

Ganged rails

Note: The ganged rails must be aligned carefully. Two people are required to install the components.

1. Insert the rail slide and seat both rail extensions into the rear channel of your rack. We

recommend placing the top rail pin into the hole just above a National Electrical Manufactures

Association (NEMA) Unit (U) marker.

2. Align the front of the ganged rail as shown below. Insert two retention screws in the front and

back of each rail. See the following illustration.

3. Do not fully tighten the retention screws yet. Allow some adjustment space for the installation of

the components.

Install rails into site rack from the front

For more information, refer to Celerra Tools on http://Powerlink.EMC.com

Install the retaining screw in

hole 2 of the rail.

Rear of rack

Front of rack

Ganged rail slide

Install 2 retaining screws

on each side of your rack

to hold the rails in place.

2nd screw hole

from top

CNS-001455MOD

5th screw hole

from bottom

Detail

1 Unit = 1.75 in.

ganged rails

Ganged rails

extensions

After inserting the rail

extensions, install 2 screws

on each side of your rack

to hold the rails in place.

Rail extensions

2nd screw hole

from the top of the rail

5th screw hole

from the bottom

of the rail

Install the retaining screws

Threaded

screw holes

Threaded

screw holes

Inhaltsverzeichnis

Andere EMC Lagerung Handbücher

EMC

EMC Atmos Montageanleitung

EMC

EMC Data Domain DD990 Montageanleitung

EMC

EMC Celerra NS20FC Bedienungsanleitung

EMC

EMC CloudBoost 100 Montageanleitung

EMC

EMC VNXe3200 Bedienungsanleitung

EMC

EMC Data Domain DD860 Montageanleitung

EMC

EMC Celerra NS20 Bedienungsanleitung

EMC

EMC Celerra Bedienungsanleitung

EMC

EMC Celerra NS40 Gebrauchsanweisung

EMC

EMC DATA DOMAIN DD4500 Montageanleitung

EMC

EMC VNX Series Bedienungsanleitung

EMC

EMC DLm120 Technisches Handbuch

EMC

EMC VNX Series Betriebsanleitung

EMC

EMC VNX Series Betriebsanleitung

EMC

EMC AX4-5 Bedienungsanleitung

EMC

EMC CLARiiON AX150 Series Produkthandbuch

EMC

EMC CLARiiON CX4-120 Bedienungsanleitung

EMC

EMC D860 Archiver Montageanleitung

EMC

EMC CX500I - Insignia CLARiiON NAS Server Bedienungsanleitung

EMC

EMC Atmos Montageanleitung

EMC

EMC DL3D 1500 Service-Handbuch

EMC

EMC Iomega StorCenter ix2-dl Bedienungsanleitung

EMC

EMC DATA DOMAIN DD160 Montageanleitung

EMC

EMC Celerra NS20 Gebrauchsanweisung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

HP P9000 Bedienungsanleitung