Emerio BH-216560.1 Bedienungsanleitung

BH-216560.1

Bathroom Heater (EN)

Badheizung (DE)

Radiateur pour salles de bains (FR)

Termoventilatore da bagno (IT)

- 1 -

Content –Inhalt –Teneur –Contenuto

Instruction manual –English......................................................................................- 2 -

Bedienungsanleitung –Deutsch...............................................................................- 15 -

Mode d‘emploi – Français ........................................................................................- 29 -

Manuale d'istruzioni –Italiano.................................................................................- 43 -

- 2 -

Instruction manual –English

FOR YOUR OWN SAFETY

1. Read and save these instructions. Attention: pictures in the

IM are for reference only.

2. This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction

concerning use of the appliance in a safe way and

understand the hazards involved.

3. Children shall not play with the appliance.

4. Cleaning and user maintenance shall not be made by

children without supervision.

5. Children of less than 3 years should be kept away unless

continuously supervised.

6. Children aged from 3 years and less than 8 years shall only

switch on/off the appliance provided that it has been

placed or installed in its intended normal operating

position and they have been given supervision or

instruction concerning use of the appliance in a safe way

and understand the hazards involved. Children aged from

3 years and less than 8 years shall not plug in, regulate and

clean the appliance or perform user maintenance.

7. CAUTION —Some parts of this product can become very

hot and cause burns. Particular attention has to be given

where children and vulnerable people are present.

8. WARNING: This heater is not equipped with a device to

control the room temperature. Do not use this heater in

small rooms when they are occupied by persons not

capable of leaving the room on their own, unless constant

supervision is provided.

9. If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

- 3 -

10. This appliance is intended to be used in household and

similar applications.

11. Do not leave your home while the appliance is in use.

Ensure that the switch is in OFF (0) position. Always unplug

the appliance when not in use. Do not pull the cord to

unplug the heater.

12. Keep combustible material such as furniture, cushions,

bedding, paper, clothes, curtains etc. at least 100 cm away

from the fan heater.

13. WARNING: In order to avoid overheating, do not cover the

heater.

14. The heater must not be located immediately below a

socket outlet.

15. Do not allow any objects to enter any ventilation opening

as this may cause electric shock, fire or damage to the

heater.

16. Store in a cool dry place when not in use.

17. Do not insert or pull out the plug with wet hands as this

may cause electrical shock.

18. The appliance should not be operated by means of an

external timer-switch or by means of a separate system

with remote control not originally belonging to this

appliance.

19. This heating device is not suitable for assembling in

vehicles and machines.

20. WARNING: In order to avoid a hazard for very young

children, this heater should be installed so that the lowest

heated rail is at least 600 mm above the floor.

21. WARNING: The heater must not be used if the glass panel

is damaged.

22. means “DO NOT COVER”.

- 4 -

23. Caution, hot surface.

WARNING!! Please do not touch surface while in use. The

temperature of accessible surfaces may be high when the

appliance is operating.

24. Regarding the information pertaining to the installation,

please refer to the below paragraph of the manual.

- 5 -

BH-216560.1 EN

PARTS DESCRIPTION

1. Heating panel

2. Power switch

3. Body sensor

4. LED display and control panel

5. Towel racks

6. Air outlet of PTC heating

7. Temperature sensor

LED display and control panel

1. Value increase

2. Value decrease

3. Timer button

4. Panel heating / window open detection button

5. Mode button

6. Power button of PTC heating

7. Program button for UP mode

8. On/standby button

9. High power / low power icon of PTC heating

10. Defrost icon

11. Panel heating icon

12. Time icon

13. Window open detection icon

14. Body sensor icon

15. Week day icons

16. Room temperature

- 6 -

WALL MOUNTING

1. Choose a wall where has enough space and is suitable to install the appliance.

2. Use the enclosed template to mark the holes to be drilled on the wall. Then drill 4 holes Φ6 each into the

wall. Insert the plastic expansion bolts into the holes.

3. Fix the wall bracket to the two upper holes using two ST4X35 screws

- 7 -

4. Fasten the two Z-brackets to the back of the heater with two M4X8screws.

5. Insert the smaller towel rack into the provided brackets (higher position) and screw it tight with four

M4X16screws. Follow the same way to fix the larger towel rack to the brackets in lower position with four

M4X16 screws. Both tower racks can be slided up and down. (Skip this step when towel racks are not

needed.)

6. Two person are required for the following assembly steps：Place the appliance on the wall bracket and

fasten it on the left and right side with two M4X10 screws to the wall bracket.

- 8 -

7. Fix the Z-brackets to the wall with two ST4X35 screws. The screws should fit into the two previously drilled

lower holes. Wipe the surface of the appliance with a soft cloth. The appliance is ready for operation.

OPERATION

Plug the appliance into an appropriate electrical outlet. Power on the appliance by pressing the power switch

to position “I”. Display and control panel will light up for 10s. Now, the appliance is standby.

To power off the appliance, push the power switch to position “O”and disconnect the plug.

Touch once to turn on the appliance.

Note: Button light will go out in 10s when no operation is conducted. Touch any button could reactivate the

button light.

Touch once again to turn off the appliance, and it will stay at standby mode.

Note: Motor will continue working for extra 15s to drive away the residue heat inside unit before turning off.

1. Set local day and time

When first use, icon will keep flashing to remind user to set local day and time before further operation.

Long touch button for 3 seconds to activate timer setting, figure 1 of will

flash, touch button “+”or “–” to select the day, the selected figure will flash accordingly. Touch button

to confirm day setting. Then come to hour-setting, flashes, touch button “+”or “–” to select the hour

among 0-23, touch button to confirm hour setting. Then come to minute-setting, flashes, touch

button “+”or “–” to select the minute among 0- 59. Touch button to confirm minute setting.

Note: program will automatically return to initial display in 10s if no operation is conducted during setting.

How to check the current time: touch button once, the display will show the currenct time, first the hour

then the minute; then it will show the current temperature again.

- 9 -

2. Power setting

1) PTC heating (1800W): Touch button to turn on the appliance. Both icons light up, PTC

heating is working at high power 1800W. Touch once to switch it to low power 1100W, only one

icon lights up.

2) Panel Heating (200W): Touch button once to start panel heating. Touch the button again to stop the

panel heating.

3) Full power heating (2000W): When panel heating works, touch button to switch PTC heating at high

power 1800W. Then total power is 2000W.

Note: at this stage, touch button will switch PTC heating from high power –low power –no power

(1800W- 1100W- 0W).

WARNING: The glass surface and air outlet bottom will become very hot. Be careful and avoid touching

it.

3. Temperature setting

After the power is set, touch button “+”or “–” to set the temperature among 5-40℃. Display will

change accordingly. Once the temperature is set, the setting will be confirmed in 5s automatically.

When the ambient temperature reaches the set temperature, appliance will stop heating.

When the ambient temperature drops 1 ℃lower than the setting, appliance will resume heating to keep the

ambient temperature at the set level.

Note: the set temperature must be higher than the ambient temperature. Or appliance will not start heating.

4. Mode setting of week timer

Touch button to switch working mode among P1-P2-P3-P4-P5-UP. After choosing your desired mode,

just leave it for 3 seconds for confirmation.

1) P1, P2, P3, P4, P5 modes are default program for quick setting

Mode

Week

day

Working mode

Anti-frost

Comfort

Anti-frost

comfort

Anti-frost

comfort

Anti-frost

1-7

00:00-