Emerson Anderson Greenwood 81 Series Bedienungsanleitung

ANDERSON GREENWOOD SERIES 81 SPRING OPERATED PRESSURE RELIEF VALVES

INSTALLATION AND MAINTENANCE INSTRUCTIONS

Before installation these instructions must be fully read and understood

Emerson.com/FinalControl

Installation and Maintenance Instructions for

Series 81 Spring Operated Pressure Relief

Valves (SOPRV).

The intent of these instructions is to acquaint

the user with the storage, installation and

operation of this product. Please read these

instructions carefully before installation.

1 GENERAL

The Anderson Greenwood Series 81 Relief Valve

is a direct acting spring loaded valve for gas

service and uses a plastic seat and O-ring seals.

The intent of these instructions is to acquaint

the user with the maintenance of this product.

Please read these instructions carefully. This

product should only be used in accordance

with the applicable operating instructions and

within the application specifications of the

original purchase order. The Installation and

2 VALVE REPAIR (-4, -6, -8 ORIFICE)

Refer to Figure 1

2.1 Disassembly

2.1.1 Relieve spring tension and back

blowdown adjusting screw out two turns.

2.1.2 Remove inlet bushing, bushing seal and

valve internals.

2.1.3 Separate nozzle from guide by hitting top

of spindle on soft surface.

2.2 Repair

2.2.1 Hold spindle by skirt O.D. in soft jaw vise

and replace seat.

2.2.2 Examine nozzle and polish out any

scratches or nicks. Replace if necessary.

2.2.3 To obtain better seat seal with PTFE at

low set pressures, burnish seat against

nozzle by chucking spindle in lathe and

holding nozzle against spindle. Burnish

with small force and for short time as

PTFE readily deforms.

VCIOM-06062-EN 19/03

2.3 Assembly

Assemble in reverse order of disassembly.

Donot lubricate spindle or guide. Make sure

the nozzle is fully and evenly seated in guide.

This is a press fit joint. Lubricate threads and

pressure adjustment screw tip.

2.4 Soft goods repair kit

The part numbers for soft goods repair kits are

listed below. Each kit contains the seat and all

seals for the pressure ranges indicated.

Engineering Doc. #05.9040.071 Rev. N

TABLE OF CONTENTS

1. General........................................................... 1

2. Valve repair (-4, -6, -8 orifice)....................... 1

3. Valve repair (F, G, H and J orifice)................ 2

4. Valve adjustment........................................... 3

5. Seat leakage .................................................. 4

6. Set pressure change..................................... 4

Operational Safety Instructions (available at

Emerson.com/FinalControl) should be fully read

and understood before returning this product to

service after maintenance.

ANDERSON GREENWOOD SERIES 81 SPRING OPERATED PRESSURE RELIEF VALVES

INSTALLATION AND MAINTENANCE INSTRUCTIONS

FIGURE 2

Series 81 (F, G, H and J Orifices)

3 VALVE REPAIR (F, G, H AND J ORIFICE)

Refer to Figure 2

3.1 Disassembly

3.1.1 Relieve spring tension and back

blowdown screw out two turns.

3.1.2

Remove spring bonnet and valve internals.

Note: a pipe nipple can be attached to vent

holes in top of guide to facilitate removal.

(⅛”-NPT: F, G or ¼”-NPT: H, J)

3.1.3 Separate nozzle from guide by hitting top

of spindle on soft surface.

3.2 Repair

3.2.1 Hold spindle by skirt O.D. in soft jaw vise

and replace seat.

3.2.2 Examine nozzle and polish seating

surface as required. Replace if necessary.

3.3 Assembly

Assemble in reverse order of disassembly.

Do not lubricate spindle or guide. Make sure

the guide plugs, if used, are flush or below

the top guide surface. Refer to table for plug

requirements. Make sure nozzle is fully and

evenly seated in guide. This is a press fit joint.

Lubricate threads and pressure adjustment

screw tip.

Orifice Set pressure (psig) Quantity

FAbove 354 2

GAbove 223 2

HAbove 227 3

JAbove 142 3

Pressure adjustment

screw

Pressure seal

Spring washer

Spindle

Drive pin

Blowdown

adjustment

screw

Guide

Seat

Bonnet seal

Bonnet

Seat

Blowdown seal

Nozzle seal

Nozzle

Body

Retainer screw

FIGURE 1

Series 81 (-4, -6, -8 Orifices)

• Parts contained in kit

Pressure

adjustment screw

Spring washer

Spindle

Drive pin

Blowdown

adjustment

screw

Guide

• Seat

• Blowdown seal

• Bushing seal

Nozzle

Body

Bushing

Retainer

screw

Orifice TFE/KEL-F

Set pressure range

Vespel

Set pressure range

psig kpag psig kpag

-4 04.4805.001 20-4000 138-27579 04.4805.002 4001 and up 27586 and up

-6 04.4805.003 20-1500 138-10342 04.4805.004 1501 and up 10349 and up

-8 04.4805.005 20-1500 138-10342 04.4805.006 1501 and up 10349 and up

ANDERSON GREENWOOD SERIES 81 SPRING OPERATED PRESSURE RELIEF VALVES

INSTALLATION AND MAINTENANCE INSTRUCTIONS

4 VALVE ADJUSTMENT

4.1 General

Two adjustments are provided on gas service

valves, one for adjusting the opening pressure

and one for adjusting the closing pressure.

4.2 Set pressure

Turn spring adjustment screw on bonnet in most

of the way. Increase pressure to desired level

and back out screw until valve pops. Lock screw

with jam nut and retest. Readjust as required.

4.3 Reseat pressure

To adjust blowdown, turn blowdown adjustment

screw IN to shorten blowdown; OUT to increase

blowdown.

Note: if volume of test set up is too small,

blowdown will be set too short even though

pressure gauge indicates it to be correct.

Referto Section 4.5.

4.4 Adjustments tolerances

Two adjustments are provided on gas service

valves, one for adjusting the opening pressure

and one for adjusting the closing pressure.

SET PRESSURE RANGE

psig kpag Valve operating characteristic Tolerance*

Above 70 Above 483 Set pressure ±3%

70 and below 483 and below Set pressure ±2 psi (±13.8 kpa)

100 and above 689 and above Cracking pressure 95%

50 to 99 345 to 683 Cracking pressure 90 %

Below 50 Below 345 Cracking pressure 85%

100 and above 689 and above Reseat pressure 93%

50 to 99 345 to 683 Reseat pressure 90%

Below 50 Below 345 Reseat pressure 80%

* Percent tolerance is of specified set pressure

3.4 Soft goods repair kit

The part numbers for soft goods repair kits are listed below. Each kit contains the seat and seals

for all pressure ranges indicated.

Orifice TFE/KEL-F

Set pressure range

Vespel

Set pressure range

psig kpag psig kpag

4.5 Adjusting equipment

Where practical, valves should be set using

an accumulator large enough to accurately

read and set blowdown. For a -4 orifice up

to 4000psig (27579 kpag), -6 orifice up to

1410psig (9722 kpag) and a -8 orifice up to

600psig (4137kpag), a four cubic foot (0.113m3)

accumulator is recommended. Thesupply pipe

to the valve should be the same size as the inlet

or larger and not more than 10” (254 mm) long.

For all other valves, or if an accumulator is

not available for the sizes listed above, the

blowdown may be set using the following

method.

Turn the blowdown adjusting bolt all the way in

until it just touches the guide, then turn it out

the number of turns listed in the table.

F04.4805.007 20-750 138-5171 04.4805.008 ≥ 751 ≥ 5178

G04.4805.009 20-750 138-5171 04.4805.010 ≥ 751 ≥ 5178

H04.4805.011 20-750 138-5171 04.4805.012 ≥ 751 ≥ 5178

J04.4805.013 20-750 138-5171 04.4805.014 ≥ 751 ≥ 5178

ANDERSON GREENWOOD SERIES 81 SPRING OPERATED PRESSURE RELIEF VALVES

INSTALLATION AND MAINTENANCE INSTRUCTIONS

5 SEAT LEAKAGE

5.1 General

If the valve leaks after repair check the following:

5.1.1 Full and even seating of nozzle and guide.

5.1.2 Foreign particles trapped between the

seat and nozzle. If any are found they

may have damaged the seat, making it

necessary to replace it.

5.1.3 Correct seat material for the valve

set pressure.If items 1 and 2 reveal

no evident seat leakage source, the

procedures described in Section 5.2 may

be used to eliminate seat leakage. Section

5.2 applies only to teflon seated -4, -6, or

-8 orifice Series 81’s with nameplate set

pressures that do not exceed 300 psig

(2068 kpag).

5.2 Seat sealing procedures

Heat the valve for 15 to 30 minutes in a

oven preheated to 250-300°F (121-149°C).

Aconcentrated heat source such as a heat

gun or open flame must not be used. After

the valve has air-cooled to room temperature,

retest per Section 4.0 to insure seat tightness.

If results have not improved, the valve should

be disassembled and the seat replaced.

6 SET PRESSURE CHANGE

If the set pressure is changed more than ±5%

from the nameplate set pressure, the spring,

spring washers, spring bonnet, guide plugs and

seat may also have to be changed. Consult the

factory or refer to the soft goods repair kit, the

table in Section 3.3 and spring chart 03.0079.

BLOWDOWN ADJUSTMENT

Set pressure range

Orifice Turns out of blowdown screw psig kpag

Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product.

Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.

Anderson Greenwood is a mark owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson Automation

Solutions, Emerson and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners.

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be

construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by

our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without

notice.

Emerson.com/FinalControl

-4 120-4000 138-27579

1½ > 4000 > 27579

-6 ¾20-1410 138-9722

1¼ > 1410 > 9722

-8 1½ 20-600 138-4137

2½ > 600 > 4137

-F 120-700 138-4826

1½ > 700 > 4826

-G 1¾ 20-700 138-4826

2¼ > 700 > 4826

-H, -J ¾20-700 138-4826

1½ > 700 > 4826

Andere Emerson Steuereinheit Handbücher

Emerson

Emerson Keystone EPI2 Bedienungsanleitung

Emerson

Emerson MVME7616E Kurzanleitung

Emerson

Emerson Enardo ES-800 Series Bedienungsanleitung

Emerson

Emerson Fisher Types N480 Bedienungsanleitung

Emerson

Emerson Fisher GX Bedienungsanleitung

Emerson

Emerson Fisher OSE Bedienungsanleitung

Emerson

Emerson VAREC 3600B Series Bedienungs- und Wartungshandbuch

Emerson

Emerson FISHER Enardo Rim Vent Bedienungsanleitung

Emerson

Emerson Alco Controls Thermo-TX7 Bedienungsanleitung

Emerson

Emerson Bettis Q series Bedienungsanleitung

Emerson

Emerson Alco Controls M36 Series Bedienungsanleitung

Emerson

Emerson ALCO CONTROLS BVE Series Bedienungsanleitung

Emerson

Emerson KTM RICHARDS FIGURE R382 Bedienungsanleitung

Emerson

Emerson Fisher V250 Bedienungsanleitung

Emerson

Emerson Fisher 8540 Bedienungsanleitung

Emerson

Emerson Fisher FLOBOSS 407 Bedienungsanleitung

Emerson

Emerson Anderson Greenwood M4TL Bedienungsanleitung

Emerson

Emerson ASCO 353 Series Bedienungsanleitung

Emerson

Emerson KEYSTONE F635 Montageanleitung

Emerson

Emerson Fisher 167DA Bedienungsanleitung

Emerson

Emerson FRM-2 Handbuch

Emerson

Emerson Daniel 700 Series Bedienungsanleitung

Emerson

Emerson Keystone Figure 969 Hopper Bedienungsanleitung

Emerson

Emerson VersaMax CPU001 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung